My Bank 2 Sensor 2 oxygen sensor is faulty and I need to replace it. The guys at the parts store were pretty certain it is downstream driver's side, but I just want to make sure before I PB Blasted and removed it. 2008 F250 SD v10 ....
View 1 RepliesLong time follower, first time user. 99 F250 V10 180,000 miles: About a month ago I replaced both upstream oxygen sensors. I know have the following codes:
0135 and 0155 for Upstream Heated Oxygen Sensor Heater HTR 21 and 11
Circuit Malfunction Bank 1 and 2
1409 for Exhaust Gas Recirculation Vacuum Regulator Solenoid Circuit
I checked fuses and PCM relay and all are good. I have 12 volts to both oxygen sensors and no noticeable wire burns. One of the possible causes given on code printout for 0135/0155 is to check for a disconnected hose to the EGR. All hoses are good. One of the possible reported fixes for EGR code 1409 is to repair oxygen sensor wiring. So my question is: Are these codes related. If I replace the EGR vacuum regulator solenoid, will this clear my codes from the oxygen sensors?
So I just replace my Cat. Converter with all new sensors in them. I just replaced my spark plugs. (I'm knocking out these check engine light problems) and I think I'm getting close to the root as to why these other parts went bad. Why my o2 sensor would be stuck on "lean" ....
View 5 RepliesI keep getting a lean bank code. I have cleaned tb and replaced one of the rubber lines. It only comes on when I take a good ride with the truck. Not sure what else it could be. I'm thinking O2 sensor maybe.
2008 F-350 5.4 3V. 65k miles
I own a 1998 Mitsubishi Mirage with about 190,000 miles on it. The engine light has started coming on and I get three codes:
P0170 Fuel Trim Bank 1P0136 Oxygen Sensor Bank 1 Sensor 2P0301 Cylinder 1 misfire
Read more: [URL] ....
The service truck threw a CEL, and i pulled oxygen sensor performance bank one sensor one code. That would be driver side sensor between the manifold and cat, rite? Don't want to change the wrong one...
View 11 RepliesI have a 2010 Toyota Corolla 1.8L, the base model.
I recently had a check engine light, VSC off light (blinking) and traction control light come on. I took it to Autozone and had a p0037 code ring up for a new Bank 1 Sensor 2 oxygen sensor (downstream). I believe I have found the correct sensor (located under car, approximately near drivers seat) and it looks simple to replace, aside from the fact that the wires go through the car body.
Can confirm that I have located the correct sensor? And if so, what is the best way to get to where the wires connect?
Is it located under the drivers seat? What should I do about the rubber grommet located under the car where the wires appear to pass through?
I am running a 2008 Ford F-250 with the DPF Delete and the Mini Maxx Tunner. I have replaced the ECT (Engine Coolant Temp Sensor) as well as the EGR Valve and housing troubleshooting this issue. Both the Engine light and the coolant icon come on when I turn on the vehicle. I am getting a P0117 Engine Coolant Temperature Circuit Low code on the Mini Maxx.
From a cold start with codes cleared if I turn the engine to ON even without starting the engine the Engine codes will come on and the the Mini Maxx will read engine coolant temp 302 and will go into Defueling Mode. I have repeatedly tried removing and reattaching the connector to the ECT thinking it could be loose connection. I can't drive the truck because there is no power and i know the engine is not hot because I have let it sit all night before doing these tests. I do not have a scanner to test other than the Mini Maxx. Other notes: I have checked Coolant I have checked Oil
I recently bought a 2008 F250 with the 6.4 diesel indirectly from a dealership. The truck itself has 220,000ish kilometers, but the engine (as well as the turbos) are Ford reman that had about 12,000km when I bought it and I have only put about 6500km on it. It is already leaking oil but that is for another thread.
The reverse sensors, steering wheel controls and part of the stock 6cd radio have never worked. The towing system has errors as well. The fuel level sensor often has problems reading the new level after I put in fuel, but that is always fixed by disconnecting the batteries and forcing a hard reset.
I figured the steering wheel/cruise control problem was due to either a broken clock spring and/or the brake pressure switch. I replaced both those as well as the airbag because the horn relay failed closed when I put it back in the wheel. It did not fix the problem. The steering wheel buttons still intermittently illuminate, but the radio controls and cruise control buttons do not function regardless. The truck isn't giving any codes either.
The towing system will activate lights and brakes on a trailer as well as set the gain, but it will not detect that it is actually hooked to a trailer. I cleaned the pins, but I haven't looked any further into it. No codes for this as well.
The reverse sensors/system does not work. It will lock itself in "off". I am guessing this is because one or more of the sensors have failed, but I am skeptical that it would be just that given the trucks other problems.
The radio does work, but the auxiliary input/mode will not work. I ran the diagnostics on the radio and on 'Test 1' I got "SELF FAIL B1342 ECU" and "B2477 CONFIG". I tried to clear the codes, but I can't. I think this means the radio is kill.
We took our 2008 Prius in for a check engine light. The dealership said oxygen sensor was faulty. Changed that and had them change the serpentine belt while there due to cracks in the belt. My wife filled up the car the next day ( it took 13 gallons) but gas gauge was not registering a full tank. We drove 67 miles and I decided to pull into a gas station and see how much it would take since the gas gauge was not working properly. It took over 7 gallons.
View 8 RepliesI have a hyndai Sonata v6. It is 2006 model and has done 86K miles. It recently failed the inspection and I was told it has faulty oxygen sensors. I have replaced the sensors. But now I am advised by the mechanic that I need to drive abut 200 miles before I can take it for the inspection again because it takes some time for the sensors to get adjusted. Is that true ?
View 7 RepliesI thought this strange occurrence I am about to describe was maybe happening because of a faulty air-fuel oxygen sensor, that I knew was bad do to a code test that was done, when my check engine light came on. However, after changing the air-fuel oxygen sensor, doing a reset on my check engine light over the weekend, this same occurrence is happening, to spite the check engine light remaining off. Here is what is happening.
When I start and drive it to normal driving temperature then put the car in "Park" with nothing turned on, the car will shake the idle speed will move up and down until it will eventually kill.
Special Note: It does not always have a idle drop and kill the engine every time. If I turn the A/C on in "Park" it idles up higher and does not ever kill. Could it be a bad Idle Air Control Motor?
99 5.4 F250
Well, this truck i have had many many codes before. I cleared them and all went away except for p0155. I fixed my manifold leaks and cleared the codes. It came back on and i changed the o2 sensor, twice. Still on.
Ive checked the heater and input wires to the pcm and have .6 ohms each, so they are good with what appears to be no shorts. I dont know how to check the other 2 o2 sensor wires.
I have a ford f250 super duty and it wont start I have checked obvious reasons and I think it might be a crank shaft sensor. Just curious, is there two of them one for right bank and left bank or just one on drivers side?
View 2 RepliesI have noticed my trans temp gauge needle is dead center of the gauge even on a cold start. I thought my sensor was under the pan so I pulled it and did not see any sensor at all. Is there a external sensor?
View 5 RepliesI have the 2012 XL F-250 6.2 v8 , I have an ambient (outside air) temperature sensor that needs replacing, I ordered it and was told it is located in the passenger side mirror from the parts guy, there is a tap in the bottom of the mirror to access it, looking for a replacement type video link of how to do this, as I am not finding one via youtube, pulling the tab off on the bottom of the mirror I am not really seeing the part I have as a replacement in the mirror.. This is the XL version/work truck so ALL manual mirrors....
View 1 RepliesI have a 2004 Corolla with a Check Engine light on. The Toyota dealer diagnosed this as: "Oxygen Sensor Bank 1 Sensor 1 - slow to respond".
The diagnostic code is PO133. Elsewhere, I find that this code indicates:
The oxygen sensor is faulty.
The wiring to the sensor is broken / frayed.
There is an exhaust leak
Haven't noticed exhaust leakage, and I doubt the wiring is faulty.
1) Where is sensor 1?
2) Do I really need a new sensor, or can I clean the old one?
My engine light just went on and the fault codes are:
P0138 -PowerTrain (O2 Sensor Circuit High Voltage Bank 1 Sensor 2)
P0607 - PowerTrain Control Module Performance
I have just bought Denso 234-4305 Rear Sensor but I was wondering if there are any guides to show where it's located?
The only guides I found is for the 9th Gen Corolla.
The Car has 88k miles on it so I guess it's outside the emissions warranty. Thus what is the price of a new ECU just in case that's the problem?
What exactly does the sensor on the rear axle do? 08' f350. I know it's a speed sensor of some sort, but what does it do or control exactly.
View 3 Replies1999 Ranger 4x4 4.0 - P0135 O2 Sensor Heater Circuit (Bank 1 Sensor 1)
I have replaced the 02 Sensor, Passenger Side (Pre-Cat), with a Motorcraft DY831...
I reset the Check Engine fault codes, and took it out for a 50 mile journey... Check Engine light is back on, with the same exact code... What next?
I understand that it may be a fuse, and/or it may be a short in the wiring... Exactly how to test the wiring from the connector at the 02 Sensor all the way back to wherever I need to test?
I really need detailed directions, like wire colors, voltage required, or ohms, or whatever is included in this process...
I recently picked up a 2005 f250 SD 5.4 4x4... I was having issues with sporadic shifting and wandering shifts while cruising around 100kph, scanned it and came up with p0721 OSS sensor circuit performance fault.
I checked the harness and all looks fine, now I attempted to remove the OSS at the rear of the tranny, got the 8mm bolt out however could not, for the life of me get the sensor out. I tried not to use pliers to twist the sensor or anything for fear of breaking the sensor off and having bits go into the transmission.