Ford Super Duty (1999-2016) :: 2008 F250 - Throwing Code - No Power - Misfiring?
Jul 20, 2013
My 2008 f250 6.4l just got out of the shop a week a go new small block and new pistons, throwing #1 constrabution code,map sensor and #1 cil misfire you can hear air come out of the intake, I am guessing valve train or lifter..... other problem two days after the truck throwing the codes i went to take it to the shop and would barely drive floored struggle to go 10mph put it in park rev up normal will go in reverse normal just no power in drive, no transmission codes, had it towed to the diesel shop, mech said might be a fail safe on transmission from the engine codes? it has egr/dfp h&s mini maxx tuner, the truck has 170k on body 11k on new engine before the new block that was put in last week.
View 6 Replies
Advertisement
2008, 5.4 liter, F250, with 6-speed manual transmission
My truck was running fine until I decided to clean my engine. I just wanted to remove the extra dust covering it, so I used a low pressure garden hose to wash away the dirt that had accumulated last winter and spring.
It started throwing codes like Fuel Rail pressure sensors, P0191, P0192. I had no power, and I could hardly drive the truck.
I figured I had some water in some connectors, so I checked around, but could not detect any moisture.
I kept driving it, and the problem got less severe. One warm summer day, I drove my truck for about an hour trip, and everything looked fine after this. Problem never came back.
I was even noticing that it was better on gas that ever before, I was doing 11liters/100km, in city driving.
Until one day (2 months later), I had to disconnect the battery to do some servicing on my truck (more that 30 minutes), and it started to run crappy again, having some piston misfire, throwing codes P2198 and P2196, (O2 sensors). No power, if I am very gentle on the gas pedal, I can manage it, but as soon as i try to accelerate, runs like crap, black smoke coming out of the exhaust.
The problem comes and goes, sometimes, the problem stops, and I can get going, no issues. Air filter is clean, even tried with no air filter, no differences., but it really sounds like bad air/fuel mixture.
View 2 Replies
I've had the truck for almost a year. It had 2900mi when I bought it. It's got 18k on it now. A few weeks ago I stopped to get the mail and the dash started going crazy throwing every warning you could think of. I got back in and all the codes were gone. I figured it was a fluke until last week. It did it again. I let it run for a few minutes and decided to turn it off. It wouldn't start back up right away. After about 20min, it started and I drove straight to the dealer.
They had it for 2 days, cleared all the codes and couldn't replicate it. They said the codes were U codes and not real codes?? The next morning it did the same thing again. I took it back and after 3 days, they said they could only think that my AMP Powersteps were the cause. They disconnected the steps and wanted to keep it for a few more days. I said no and picked it back up. It made it 2 days and I got the codes again.
[URL]
View 6 Replies
I recently bought a h&s tuner and installed a dpf delete kit. Everything works great when the truck is not plugged in to the tuner although when I do plug it in, the truck keeps throwing a communications code and goes into a limp mode until I delete the code. I believe it was p0073 but i maye be mistaken. Regardless it has to do with communicating through the obd2 port. I sent the tuner in to get checked out and it turns out its something to do with the truck. I've checked all the fuses and tried to check for broken wires. Where to look next?
View 4 Replies
I've got a 2006 F350 5.4L.
The ABS light came on and it was throwing a 'rear speed sensor' code. I searched around and it seemed to be a common issue that the sensor goes bad and needs to be replaced.
I bought a sensor and replaced it, but in doing so, I saw that while the sensor was indeed bad (cracked) the wire right at the connector was corroded.
I replaced the sensor but the ABS light is still on the dash. Is it possible that they code simply needs to be cleared? I was able to read it with my OBD2 dongle and Dash Command App, but maybe I'm not able to clear it?
Or is it more likely that the corroded wire on the connector is the issue? (it wasn't fully corroded and I cleaned it up and sealed it.). It didn't look like I could pull the wires out of the connector, so I assume I'll need a new connector. What is the part number?
View 2 Replies
I just bought a 99 F250 Super Duty with the V10. When I bought it, I knew it had 2 misfiring cylinders (4 and 10) because it was throwing P0304 and P0310 (only 2 codes), but wasn't concerned as I've had to take care of my wife's Escape with it's misfiring cylinders. I replaced the 2 coils and replaced the plugs with Motorcraft plugs from O'Reilly's, cleared the codes and she ran fine for a couple of days. Now I'm getting an intermittent misfire, it's only occasionally throwing a pending code of P0300 which is "Multiple Random Misfire".
I'm fairly certain it's an issue on the electrical side because if it were an issue with the injector or injectors it would be constant regardless of RPM... right? As it is now, it basically does it between 55-65 while in overdrive trying to pull a hill or slightly accelerate. Once it's shifted out and the RPMs go up to 2k+ it runs like a champ... and it kills my fuel economy. The way it's behaving is just like when a coil is bad, but it's saying it's not identifying a specific cylinder (saying it's multiple) and it doesn't always do it (about 60% of the time).
I checked the MAF and it's very clean (looks almost new), checked the vacuum lines (those I found without a manual) and couldn't find any leaks and when I changed the plugs all the plug wells were dry.
View 6 Replies
I am running a 2008 Ford F-250 with the DPF Delete and the Mini Maxx Tunner. I have replaced the ECT (Engine Coolant Temp Sensor) as well as the EGR Valve and housing troubleshooting this issue. Both the Engine light and the coolant icon come on when I turn on the vehicle. I am getting a P0117 Engine Coolant Temperature Circuit Low code on the Mini Maxx.
From a cold start with codes cleared if I turn the engine to ON even without starting the engine the Engine codes will come on and the the Mini Maxx will read engine coolant temp 302 and will go into Defueling Mode. I have repeatedly tried removing and reattaching the connector to the ECT thinking it could be loose connection. I can't drive the truck because there is no power and i know the engine is not hot because I have let it sit all night before doing these tests. I do not have a scanner to test other than the Mini Maxx. Other notes: I have checked Coolant I have checked Oil
View 3 Replies
I have a 2009 f250 with 5.4l 3v. have had the truck only about 6 months. it started missing about a month after I got it. I replaced all 8 cops and all 8 sp. The truck ran excellent until 11/29, then I got a cel and the truck started running really bad. Found 3 misfiring cylinders. Changed all 3 cops again and that did nothing. Pulled the injectors and found 2 of them were clogged, replaced those also. Still no change was told by someone that the ecm/cpu may need to be reset, did that also. Still no change. There are no codes present but still has the multiple misfires.
View 9 Replies
I have a 2012 F250, 6.2L, Crew Cab, FX4 with a little over 77,000 miles on it. I bought it used from a Ford dealership last summer. Prior to now, I've only had one issue with it and that was squirrel/rodent induced. Something chewed through the wiring harness right before the connection to the #7 cylinder. There was enough left over wire to solder it back together and put heat shrink around each wire.
It ran fine up until last weekend. The wife and I went to a store, she was driving and parked like a total jerk right in the front area of the parking lot. When we got back in the truck, she started it up and it was just running rough with hardly any power. My first thought was someone dumped something into the gas due to her amazing parking, but there were no smells or residue of anything near the gas cap when we got home only a couple miles away.
When I got home I ran my code scanner and found 300, 301, 305, 307, and 308. I dumped a bottle of ISO-Heet in it, let it sit for a bit then cranked her up and ran it for a few miles to the gas station and filled up...about 25/26 gallons, I don't remember...I was a little above 1/4 tank when this all started. No change in performance and the codes were all still the same. I pulled the MAF, it looked clean, but I wiped it down anyways and threw it back in. No change. I then changed all the plugs. This took care of 301 and 305 but 300, 307, and 308 were still coming up. I then picked up two new coil packs for cylinders 7 and 8, threw them on and still no change.
I sat with it running on a flat surface for a little while revving the engine randomly for about 15 minutes, during this I noticed a fast tapping noise at about 3400 RPM, it went away quickly with no changes in the gauges on the dash. I cant really tell where it's coming from, but kinda sounds like its under the middle of the truck. While sitting there I ran the codes again, and now its back to 300, 301, 307, and 308. I'm now at a loss of what to even look at...
I've also checked the voltage coming off the harness at the connector to the coil packs...just under 11 volts. I've searched all over for what that voltage is supposed to be, but have failed miserably in my searches.
View 6 Replies
6.4 diesel 2008 F250.... I have been having lots of trouble with low power and sputtering of this diesel truck . It almost seems like a fuel filter but I changed them out 2 times now and the same thing keeps happening . It has been a very cold winter here and if there was any water - it would freeze.
If I am going down the highway and it starts to sputter. I put transmission into neutral and shut motor off with key. Start it up and it's good for less than a minute or two and it's back to sputtering.
View 5 Replies
I have a 2010 F250 with the V10 and 42000 miles. Lost*power*while pulling a trailer. Couldn't get over 30 mph. Tried turning back home and lost all*power*and would barely idle. Fuel filter good air filter good. Code P0300 came up. Towed it back to the house and then couldn't even get it to idle. Wouldn't throttle up past about 2800 rpm. Cleaned MAF sensor and nothing. Somewhere during all that P0174 code came up and misfire cylinder 10. Cleared codes and they haven't come back. Now when trying to crank, it barely turns over, yet battery is good. Opened air filter cover after getting it to start one time and there was some light smoke coming out. Also while barely keeping it running for a little bit, the catalytic converter on the driver side was fire hot and the other side I could grab with my hand.
View 6 Replies
My '05 F250 (5.4) started misfiring and threw codes for p0300, p0305, p0307, p0308,and p2198. I used an inline spark checker to check cops, which all had spark. Replaced 5, 6, 7, and 8 plugs and cleared codes. Ran truck for a few minutes and codes came back. Switched #5 and #6 cops and cleared codes. 5,7,and 8 cylinders still misfiring (same codes). Truck only has 36,000 miles and spent alot of time just sitting. Plugs were original plugs.
Replaced 5-8 with Autolite OEM replacements. I haven't checked cops for resistance yet. Weather was pretty cold when problem started. Threw in about 10oz. of Lucas to no avail. I had this problem last winter with the same cylinders throwing codes. Threw some Lucas in the tank and idled truck for approx. 1/2 hour and problem went away except for stumbling most every time truck came to a stop. I'm starting to wonder if it's a coil or a fuel issue.
View 10 Replies
So basically I thought it would be a great idea to degrease my motor from the top down.... After washing I start it up and drive down the road to head abunch of misfiring under heavy load or high rpm's.
My problem is that the misfiring won't throw a code. I then proceeded to buy a new ignition coil (thinking this was the problem) but with no code to go off which cylinder was bad I just switched the good ignition coil into each cylinder and starting it.
Up each time. None of them seemed to make it better. Also the injectors all seemed to be good. So what to do ?
2002 Ford F-250 5.4l
View 3 Replies
On the highway doing 100 mph. during af take over, my Ford F-250 6,4 Super Duty 2008, lost nearly all power. (now it is like driving my old hummer h1)
Engine and car runs/starts great, only 10 minutes uptil 60 mph. now.
My mechanic has given up. He checked following:
EGR = OK
HOSES = OK
ERROR CODES = NONE
INTER COOLER = OK
PARTICLE FILTER CLEAN = OK
TEST WITHOUT EXHAUST = NO DIFFERENCE
FLUIDS = OK
Hopefully something I can fix with my hammer. The car has 85.000 miles on the clock.
View 14 Replies
CEL came on last night, OBD code PO420, truck is an 06 f250,5.4? Btw, truck running rough, no power on acceleration, in gear at idle, runs rough....
View 4 Replies
I've got a 08 f250 ext cab long box with the 5.4 gas. I know I know 3/4 ton gas. Trucks got NO power at all loaded and unloaded and really bad fuel mileage. Driving like a grandpa in town I'm getting 7mpg on the hwy unloaded I get 9 or 10mpg loaded on the hwy the trucks working way harder than it should and getting 6mpg.... I'm wanting to swap the 5 4 for a 6.0. Reason I saw 6.0 is my buddy's done egr delete. Bulletproof oil cooler head studs and a edge with attitude chip and has great power and reasonable fuel mileage. How hard is it going to be swapping the motors.
View 10 Replies
I have a 2008 f250 superduty with the v10. Just today I was driving and engine picked up.slight miss it's rainy. I thought coil pack, but it left me on side of road. Got fired limped home won't go more than 40mph. Runs rough, no power, checked codes and get P0340, p0357, p1336, and P2195.. Where to start.. My daily driver and have to get back on road.
View 1 Replies
While driving up hill at 60mph the truck lost power. Rpm jumped up as to change gears as it hit 55mph. Still losing power until it shut off. I tried to restart and just got a click from the solenoid. No engine codes whatsoever. Battery had 12.1 volts but when turning the key to start in getting 8 volts. Had it towed home. Today I swapped batteries with my other truck and same click noise from solenoid. All lights, radio, ect still work. Where should I start? Alternator, fuses...?? 2008 f250 5.4 ...
View 12 Replies
Seems recently my 2008 f250 diesel wants to go into 4wd all by itself. It's the electric switch on dash with the auto/lock front hubs. I'm thinking either the dash switch or the accuator motor. Where to start though... Also I can turn the switch to 4 wheel high and it doesn't go in.
View 1 Replies
Ok says injector pressure sensor low first guess was the upgrade to the blue spring. Did that code clear for a day then comes back on looking at the hfcm but kinda unsure? Came on after we got the real cold snap and i had to buy a block heater I don't see one on here i also added diesel 911 to the tank this is a 05 f250 w 6.0l....
View 2 Replies
My 99 F250 with a V10 had an abs light come on and then it would go off. Now the ABS light stays on and it drove fine for a little while but the other night the Service Engine light came on along with the ABS light. Tranny was shifting harsh, winding out and I scanned the codes and got P0500. Is it the sensor on top of the rear differential or is it the ABS light causing the problem?
View 2 Replies
