Ford Super Duty (1999-2016) :: 2008 F250 - Squeak And Clunk / Bearings Are Loose
Jun 22, 2013
My rear wheel bearing are a little loose. This afternoon while diagnosing a squeak in the back I found this. While pushing the truck side to side there is a clunk and when you lay your hand on the tire you can feel it, bearings are loose. Nothing during the operation of the truck to give this away, truck runs and drives as it should but I need to check it our before something does go wrong. What I'm looking for is a torque / preload that the rear wheel bearings need to be set at.
View 2 Replies
Advertisement
I have a 2008 F250 XLT. When i am driving and turn the wheel a squeak is noticeable while the tire is spinning. as i speed up the squeak gets faster and slower when i slow down. I have it narrowed down to the right front tire but cant figure out what is causing it.
View 5 Replies
While I was trying to park, I heard a clunk, wheels stayed in the same position. The steering wheel is loose as hell, it literally feels like its buttered up and wont turn the wheels at all, what to buy to fix it? I am thinking I just need a new gearbox....
View 6 Replies
I have a 2002 f250 super duty v10 with the manual transmission... It has aloud squeak from under the truck when Im slowing down or maintaining a certain speed. The squeak goes away when I accelerate or if I push the clutch in. It does have a vibration to it when im speeding up. And shakes bad sometimes when I let off the clutch from a stop..
View 1 Replies
My steering is "loose", All front end parts are in good shape but I can move the steering wheel 4 or 5 inches back and forth without the wheels moving. Ball joints and tie rod ends are good. Truck only has 185000 miles on it.
View 2 Replies
1999 5.4L F250 ... When I turn my ignition all my lights come on and I have power to dash and etc, battery is strong, but when I turn the key I get nothing even when I do the shifter trick for the slip we get on most fords nothing took ignition lock cylinder out and blasted it with electronic connection cleaner, when key is turn i loose all power to everything and there is no "click" or i gage from anything under the hood or the starter rally confused!
View 13 Replies
My 2010 6.4 F250 seems has a loose steering wheel. The steering of the truck hasn't changed nor has there been uneven wear on the tires. It doesn't drift if I let the steering wheel go. Had the front end inspected and was told it's all good under there.
YET, my actual steering wheel is loose. I can grab the wheel and wiggle it front to back and side to side. It FEELS like the bolts that hold the steering wheel to the column are loose. What was the cause/repair? Is this something I can repair myself or a local shop? Or is this a dealer fix?
View 2 Replies
I have a F250 SD with a 6.0 diesel. My steering wheel is loose. I tested and know for sure is not a problem inside the cabin. Fallow the line thru the linkage to the steering box by the left front wheel. I found an adjustable switch there. Just on top of the steering box. It has a lock nut that must be loosen to adjust what it looks like a hex. Very hard to reach. I have watch some Youtube videos but on different vehicles.
View 1 Replies
Just moved into the 250 from years of 150's. Now have 98 miles and read that the tran would have noise but normal while breaking in.
whats normal, not used to this much Clunk while changing from P to D ect. More noise than used too I guess.
3.73 gears
2014 F250, 6.2 gas 2wd....
View 8 Replies
I have a 2004 f250 with some front end troubles. When turning right once in a while it will make a hard CLUNK noise and then trying to drive down the street it drifts over to the left and I pull the wheel back to the right and when I turn the wheel it feels like I like theres something hitting somthing else in the front end. I have checked ball joints and tie rods and they are all nice and tight. Some stuff I have done that probably isn't related to my problem is shocks and sway bar end links. What this could be? Hopefully not the steering box!
View 7 Replies
I have a 2014 4WD Super Duty. It has a squeak that is coming from the drive shaft area. I had someone listen to it as I drove slowly next to them. It is a repetitive: squeak squeak squeak squeak squeak. Not loud. The frequency increases as speed increases. I could believe it may be a U joint based on the frequency, but seems hard to believe with a new truck. I heard this sound when I first got it, but the sound was so slight that I thought it was just some sound associated with a newer engine. But now it is becoming a bit louder.
View 4 Replies
I have a 2003 F250 Ext Cab 158" wheel base, 5.4, auto. 2wd
Last week I noticed a squeak squeak squeak while driving through town, sounded like the u-joint. I got home, jacked it up and pulled the rear shaft. Unfortunately I, bone-headedly, did not mark it when I pulled it. I took it into town and had a shop put in two new U-joints from autozone.
I got home and, forgetting to mark it, put the driveshaft in 180 degrees out. This caused the whole assembly to get out of balance and tear up the carrier bearing.
I replaced everything, pulled the complete shaft and disassembled it to put the new carrier on it...again, for some reason I didn't mark it. I knew I was supposed to.
It destroyed the carrier bearing again. So I limped it to my mechanic the next morning. He went through and replaced the front u-joint and carrier and called it good. I picked it up that afternoon and it was vibrating again.
I took it back and they kept it overnight and fixed it again. The problem they had was the driveshaft was coming back on the 'flex' and rubbing into the carrier instead of sliding back and forth, it was sticking.
They got that all fixed up and the wife picked up the truck while I was at work Friday. I called her at lunch and she said it was still squeaking like before I took it to the shop. I get home that evening and drive it and, sure enough, it's squeaking like it has a bad u-joint.
But the squeak didn't start right away, I had to drive it about 5 miles for it to start, and then I didn't hear it until I slowed down enough to get rid of the wind noise.
I took it back to the mechanic this morning. He called me around 4 and said they drove it about 25 miles around town and on the highway and couldn't duplicate the noise.
He said they went ahead and hit the grease zirks on all 3 u joints(even the ones they didn't install on the rear shaft) and they couldn't hear any squeaks. So I pick it up, drive through town a bit and start heading home. No squeaks.
I get about 20 miles out of town and slow down going over a bridge with the windows down, and there is the squeak again. Still sounds like a bad u-joint. But I didn't hear it until I drove it about 25 or 30 miles. What this noise is or what I need to be looking for?
View 1 Replies
My 2002 F250 is knocking loose the front end assembly--the gasket is worn out. So I was shopping around and was considering a beefed-up front end assembly.
View 3 Replies
Have an 06 F250. When I slow down to make a turn then accelerate it's like the drive shaft spins half a turn before it catches. Been doing it for awhile now. Now I'm get a clunk when I come to a complete stop. When you stop then truck settles there is a little clunk. Does this sound like the slip yoke problem?
View 1 Replies
I have a 2005 f250 that has a wander and a clunk what feels like under the drivers seat. The driver side bushing in the radius arm has no dirt and looks like wear on it compared to the passenger side which is completely covered in dirt. My question is, bushing wear out will cause wander and a clunk. Is it hard to replace?
View 3 Replies
When I go over good size bumps, I hear a clunk in the front tire area when my driver's window is down. It's a metal noise, like something loose.
2011 F-250 with 203K miles. Replaced shocks last year. Did this with stock wheels/tires. Something in the front suspension or axles. What should I be looking at?
View 8 Replies
I've got a 2008 Ford F250 Superduty Crew Cab. My problem is that the center console of the front bench seat is loose. I keep it folded down nearly all the time and any pressure on the front left corner causes the rear right corner to pivot up.
View 3 Replies
My 11 cc lb 4x4 6.2 has a clunking/loose sound coming from the front end. It is prominent when going over small/medium bumps but not so much large bumps. I have had my local dealer and a couple local shops look at it and they all say everything checks out. It definitely seems like something is loose in the front suspension. I just put new Gabriel max control shocks on all four corners. I have no play in wheel bearings or ball joints. Tie rod ends also look fine.
View 12 Replies
As the title says are my front leaf springs bad? I got this truck 2 years ago and replaced all the ball joints, shocks, sway bar links,front hubs, rotors and brakes along with all the seals. I have a clunk in the front and I can't figure out what it's coming from. Could my leaf springs be clacking together? Truck
is a 2000 F250 SD v10.....
Driverside front
Rear spring
View 10 Replies
My issue, just purchased f250, 2004, v 10, manual transmission, state vehicle with 32,000 miles but was a plow vehicle for localRMV lot, that said, great shape and runs strong but I get a clunk and shutter when I am in reverse and only when I push down clutch before stopping. Doesn't do it starting forward or reverse, only reverse and when I push clutch in before stopping. Did have a friend drive and looks like the transfer case is moving, as if mounts or bolts are loose. Does this make sense and could bad slip joints be putting excess torque on ?!?!?
View 4 Replies
I have an 08 F-250 CC SB 4x4 Diesel truck that has since new clunked when starting out from a stop and/or coming to a stop. I have 16k on it now and am getting really tired of dealing with it... The clunk starting is when I let off the brake and just apply the throttle. It feels like something slips and then clunk.
The clunk when stopping is the same as starting, except when coming to a stop.This is unloaded or when loaded w/ cargo and/or trailers. I know I can go to the dealer, but I don't want to un-spartan my truck for this...
View 14 Replies
