Took truck out for a ride and stopped for gas. I smelled Brakes and upon inspection found the left rear brake pads were not releasing. Any take on what could be holding it? 2008 F-250.
View 10 RepliesI have had the truck just under a year. It has 104k on it i only drive it on weekends. Last weekend going to Home Depot about 15 miles got out and could smell brakes burning. Felt the wheels and the right rear was very hot. Got back home no smell but still hot not as hot as earlier. Pulled the wheel off it looks as if the pads and calipers are fairly new paint is still on them caliper is a TRW. The pads were stuck in the carrier even the stainless clip ends look rusted.
Cleaned it all up both sides lubed the pad carrier with pin lube. Pushed the calipers back in some both sides went in easy. The right rotor has definitley been hot. Put it all back together and went for a test drive. Came back no problems checked the temperature with a laser type heat thermometer all wheels were around 140 f. Went out yesterday morning stopped and could smell the brakes again. Drove it back home and the right rear was 300 f. others 150 to 160 f.
Jacked it up put it in neutral and the you can spin the wheels by hand. Started the truck had the wife get in put it in drive wheels turning applied the brakes they stopped let go they turn freely again tried the parking brake it works fine also. So do I buy new calipers and brakes or maybe is the wheel bearing going bad causing the brakes to heat up?ied.
I recently took delivery of a new 2012 F250. It was a cab chassis, we had a utility bed and lift gate installed from the upfitter along with heavy rear springs. From day one the truck would pull left when the brakes were applied. The brake pedal also feels mushy, not firm. It will firm up when I pump it. I could also smell burning around the left front of the truck when I would get out of the cab. Hot brake smell. Took it to the dealer with only 400 miles on it and they replaced the front pads and turned the rotors, and gave it back. In relatively few miles the problem was right back again.
Took it back to the same dealer last week with 1200 miles on it now. This time they say they replaced the rotors. I went and picked it up it this morning. Within 5 miles drive of the dealership I can tell the brakes are still bad. Now, it will kind of do a "head fake" when the brakes are applied, pulling slightly left or right, before deciding which way it wants to pull. It will pull right or left now during firm braking. And the brakes were stinking by the time I had it back to them. I turned around and took it right back to them again. Brand new F250?
I keep having this problem with my 02 Superduty. The rear brakes keep locking up and smoke the pads. The truck is not driven much so that is most of the issues. it has less than 63,000 miles on it. Mostly only driven in the winter with the salt and crud so rust is a problem. What is your advice on changing so that I can get more than a year without having to do it all over again. I am going to get new calipers and the brake kit. Should I get e-brake stuff too?
View 7 RepliesI believe my brakes have a problem.
Lately, I can stomp on my brakes @ 50 mph and they won't trigger the abs or come close to skidding the tires. The peddle goes to the floor if I push hard enough and the truck doesn't seem to stop fast like it used to.
I'm wondering if there is an issue I should be focusing on, like swelling brake lines or some issue you may know of. I'll try bleeding the brakes this coming weekend, but i think its going to be a bad brake line or something.
2003 F250 V10 4x4. I have a rear brake sticking so I assume I have to replace the calipers. Which brand should I go with?
View 2 RepliesI have for the 4th time in a little over a year developed another issue with a rear caliper hanging up last year i ended up replacing both rear calipers with reman. from NAPA. 3 months ago i had to replace the right rear again. Now currently i am having the left rear starting to hang up again. I've done a fluid flush and everything. I'm kind of at a loss. I don't normally have this much trouble with brakes. Some of the symptoms that go along with this are a spongy pedal and inconsistent brake feel just like when you have air in a line.
View 1 RepliesTwo weeks ago did a road trip to NH from RI and i heard a slight dragging only at low speed (10-15mph) in my left rear tire. figured the caliber was dragging a little, it was. Before arriving in NH the brake light came on. Long story short i get back to RI and the left side noise gets worse and starts to lock up. I finally replace the rotor which was warped, pads, and caliper which was bad.
Was driving it same day and still here the same dragging and screeching noise and the brake light is still on. On my way home the left side locked up at low speed without hitting breaks and slid the truck, mid you all parts are new on that side. I am not sure what it could be at this point something in side the axle?
I have a 2006 F250 and my 7pin and 4 pin connectors are just hanging loose. I'm not sure what happened to the factory bracket. What is the part number for this bracket? Also, where does it mount to? I looked under the truck and couldnt tell where the factory one mounts.
View 4 RepliesI just changed all the pads and rotors on my 08 F350. The brakes are much better now, only the rear brakes got quite hot after driving it for about 15 min. Turns out the rear parking brakes are dragging on the back brakes. I adjusted the parking brake on both sides so they no longer drag and the heat issue is gone. The problem now it the parking brake does not engage until the pedal runs out of travel. Any tips to get this just right? Will the parking brake self adjust like the old drum brakes and shoes use to do years ago?
View 7 Replies2008 f250 abs light, check brakes fault, speedo don't work! I was hauling a car the other day and all of a sudden all these lights and faults came on then my speedo quit working and also the odo don't calculate mileage. I changed the speed sensor at the top of the rear end and still nothing. Cruise control also don't work..
View 14 RepliesMy truck is a 2008 F250 6.4 Powerstroke 4x4 King Ranch, CrewCab, Shortbed.
I don't know which rear axle ratio it has - maybe someone can help me. the tires mounted are 275/60R17 and in fifth gear (TC locked) the engine has 2000rpm @ 70mph. I think it is a bit to much so I want to install a kit with and lower ratio. I pull trailers just sometimes and here in germany these only have 3,5tons max weight. So I think I don't need this power at 70mph. 1750rpm would be enough. How do I have to modify the front axle ratio if I get a lower-ratio-rear-axle?
I want to lower the fuel consumption. After some modifications, the truck needs round about 12-13L/100km (18-20mpg) and I think it is possible to lower this as bit.
I've got a 2008 f-250 extra cab. A small bump will cause the rear driver side door to pop open. What I have to do to fix it, I don't want the grandkids falling out.
View 2 RepliesMy Superduty has been pulling to the left when I hit the brakes for a few months now. In the past it's done it, like within a year or two after buying it brand-new off the lot, but that was because one brake pad had rusted itself to the bracket and was not doing a darn thing. Once or twice more, it was a stuck caliper pin, which was quite obvious when working on it.
Last year, around August, I replaced the rotors and pads with Advanced Auto parts stuff. Rotors are still great, pads look brand-new, and it wasn't pulling up until the past month or two.
But this most recent pulling has been a problem that I can't find. It's not the pins, it's not the pads, and now I find out, it wasn't the calipers
This past weekend I went so far as to replace the calipers with Napa rebuilt "semi-loaded" calipers (all hardware and pins and bracket, except for the pads) and pressure-bleed the entire system. The old fluid was green, not black, but now that it's been bled, the pedal is a bit firmer than it was.
I wasn't going to replace the calipers without checking them first, but I broke both bleed nipples off and I wasn't about to wrestle with an easy-out and try to get the darn things out. Per side, rebuilt caliper with hardware and bracket, can't go wrong. (Checking the calipers would have involved using a C-clamp to compress the caliper slightly, then backing off the C-clamp - if the pistons come back out a slight degree, they are free and the seals are still "grabby" and resilient).
While bleeding it, I saw a piece of black crud (rubber?) about 2-3mm in size come out of the left side. Didn't think much of it, figured it was just built up crud from somewhere.
Today, the first commute after doing the calipers and bleeding, it's still pulling just like it was before the calipers. However, I did notice at one point when I hit them, they pulled like they normally do, but seemed to go straight a few seconds into it. It does seem that if I keep my foot on the brake, the pulling is much less after the initial second or two, but if I stab them again, it pulls like crazy.
And by "pull" I mean the steering wheel actually moves in my hand. So with that in mind, it's actually a front-brake problem. If it was the rears, the wheel wouldn't pull like it does, and if it was something loose in the suspension, I would have found it already after checking everything, and it again, wouldn't pull the steering wheel like that.
Now, given that black piece of whatever that came out of the left side, I'm beginning to wonder... if it was rubber from the inside of the hose.
Is the right brake hose causing the pulling because it's coming apart just like the left one might be?
I've gone over and over this in my head this morning, and thought about the ABS unit possibly dumping pressure from the right because of a leaky valve (see side note below), but I would think that once the pedal stab was over, it would even out and not pull at all.
However, this thing pulls left quite a bit, even after the pedal has been held down for quite some time. Usually. Sometimes, it subsides and doesn't pull. But mostly it does no matter what I do, keep pressure on the pedal, let up and reapply, whatever.
Does this really sound like a bad hose? It's intermittent, but usually pulls like 90% of the time.
Side note: The ABS unit in my truck, and most Fords of the time (not sure about later than 2004 or so) is a Kelsey-Hayes three-channel unit like this:
Kelsey-Hayes RWAL Antilock Brakes
It's the same system found in Chevy Suburbans and light-trucks, which I have worked on before and know a bit about.
In my case, it can't be a dump valve leaking, because it would effect pedal-height and not PULL to one side like it does. The only way that could happen is if the isolation valve was closed, AND the dump valve were leaking at the same time.
I haven't, however, gotten the ABS to activate just to see if it changes anything. On my way home tonight I will see if I can find some dirt or sand and get it going
I use a bottle hanging like an I.V. drip to flush the Brake Fluid in all my cars. I can pump all the old fluid out, as well as the air. My Superduty 7.3 has a good solid brake pedal after the flush. It seems to me the rear brakes handle 60% of the stopping load. Its been like this for so long I'm not sure if it's ever been different. i then go to a gravel or wet road and test the rear abs, and it seems o work, but definitely has a squirrely feel. I did some strong pavement stops with speed, and it stops, no skidding. Is that the way it should be?
View 14 RepliesMy 2012 f350 6 lift when I push the brakes it pulls to the left kinda bad and the steering wheel is off to the right..
View 4 RepliesSo I bought this truck a year ago and the guy had his fog lights re wired to another switch under the dash and had a brake controller wired in (that's what I think it's called) the fog lights worked for a month then just stopped working there's a rats nest of wires under the hood for the fog lights too. The brake controller never worked.
My main question is what are the wires that are hanging down under my dash that look like someone snipped ....there's a random green wire attached to one and just hanging
I have a 1999 f250 sd with the 7.3. I'm not sure what is going on with my pickup. When I turn to the right i can turn with one finger, but when I turn left i have to put some muscle into it. Power steering fluid is full. I raised the front end and it turns both ways easy. My ball joints feel fine, there is no tire shake when i have it off the ground. My tie rods feel fine also, nice and tight. I was thinking about replacing the steering sector to see if thats the issue but wanted to get a second opinion first.
View 2 RepliesI have a 1999 f250 super duty, that was wrecked a few months ago. I have put the truck back together with the mechanic. The front drivers side was wrecked. The power steering fluid tank was cracked and had to be replaced. Also had problems with a box behind the drivers headlight? I did hard wire it together and it fixed the problems I was having the the speedometer and the transmission not shifting correctly. Everything is put back together now but I drove it today and the brakes locked down after driving it a few miles?
Had to push the truck hard to get it back to my house, a mile or so. If I let off the gas it would come to a quick stop. It is ALL four brakes locking up. If it sits for awhile they unlock but will lock up again after driving. The truck is lifted and the ABS light has come on. It was not on before but i am pretty sure the ABS is disabled on the truck. The wires are hanging down by each tire. This is how they truck was when i bought it. Not sure what is causing the brakes to lock up.
So a few week back I noticed my brakes were getting soft. Soft meaning that when braking for any distance, I would hear a kind of "pressure release, squeaking" sound coming from the pedal, and the pedal would sometimes go to the floor and the ABS would kick in. Let me tell ya, its a pretty crappy feeling when your brakes aren't doing what their supposed to! So, I replaced the pads all the way around, replaced the master cylinder (bench primed). I took it out for a drive, and it did the same thing. So thinking maybe the fluid is bad, I flushed new fluid through the lines. Took it for a drive, and it felt good right away, the pedal firmed up a bit, and then it did did it again.
Just so I give as much info as possible, the rotors are looking pretty rough and going to be replaced soon.
So, my question[s] are; What is the next step in identifying the problem? Is there a chance the new master cylinder is bad? Could worn rotors cause the caliper to max out and not apply enough pressure? Even though the calipers seemed fine while replacing the pads, could one or more be bad? If so, how do I know?
was going to do a brake job on my f250 light duty and the rotors won't come off. At first I thought they were rusted on but after looking at them it looks like the studs are attached to the rotor. Need to confirm this because the new rotors I got don't have the hub attached. Don't know if it's the wrong part or what?
View 9 Replies