Ford Super Duty (1999-2016) :: 2008 F250 - Hub Assembly Removal
Jul 11, 2014
I am trying to replace the ball joint on my 2008 f-250. Does the hub assembly come off of the knuckle or do you remove the whole knuckle and hub assembly together? If you have to remove the hub assembly what is the best way?
View 14 Replies
Advertisement
My 2002 F250 is knocking loose the front end assembly--the gasket is worn out. So I was shopping around and was considering a beefed-up front end assembly.
View 3 Replies
I dont want to pry on the wrong thing and brake something. I am trying to remove the headlight. I was told that their are some pins that need to be pulled up. I dont see any pins. I do see two plastic clips on each side of the headlight. They are flat on the top with a small slot in them. There is a "T" stamped on the top of it. Are these the pins? I tried to find a shop manual today without much luck. Looking for a picture to show the pins that need to be removed.
View 7 Replies
I want to know if there are any issues when removing the rear block, also do I have to put a new block in or can I just leave it out ....
View 12 Replies
I tried searching and googling but came to no results, unless its like similar trucks. How do the 4x4 shift remove? I have an 04 F250 and someone decided to put the shift on sideways so the 4HI and etc read upside down before I purchased the truck. Do I just rip the thing off?
View 1 Replies
I would like information how to remove the rear seat back on a 2012 F250. I want to remove the head rests and from what I can find out they are bolted solid to the rear panel. I asked the same question earlier and got a reply for 2011, would that be the same? Is there any place I could get a schematic, a picture is worth a thousand words.
View 5 Replies
I have a 1999 F-250 SRW 4x2. Is there a post that explains how to remove the front brake slide pins?
View 3 Replies
Yesterday I returned my F-250 SUPERDUTY 5.4 To stock on the sct flash tuner that came on the truck. after returning it to stock i tried to start the truck to leave about an hour later and instantly wouldnt start it backfired. we returned it back to the tune that was on the truck, still no start. we replaced the starter, the battery still nothing. if it sits for a little while it will attempt to turn over. it has a strong odor of gas in which led me to possibly thinking its vapor locked? or the pcm being bad or maybe the crank shaft sensor? the truck has ran strong and had zero problems up until now when we took the tuner off. it runs about 6 codes now, a few being the kam the o2 and low voltage.
View 4 Replies
i've done some searching but haven't found any how-to's or instructions on how to remove the front bumper on my 06 f250. Any link on how to do it?
View 2 Replies
I started with removing the two bolts that hold the carrier bearing to the crossmember that attaches on each side of the frame, well the clip that basically would hold the "nut part" of the bolt on the top side sheared on both of them due to salt+calcium chloride.
It felt like there was a 6 point head up there so I tried fitting wrenches and sockets up on the other side, I finally got a good hold with an 11/16" wrench but it just kept rounding more and more. Normally I would just torch the heads off but the gas tank is right next to it.
Any tips for getting the carrier bearing bolts out now? I don't care if I destroy it they're easy to replace. Also I'm typing this from my phone so Incase my sig doesn't show this is on my 02 f250 crew short bed 4x4
View 2 Replies
I bought my 2000 F-250 CCSB a while ago and it came with 2 keys - one for the ignition, and one for the doors/tailgate - may not seem like a big deal, but it annoys me to no end.
From my understanding, the truck had previously been stolen and had the driver's side lock punched, and then something happened to the ignition lock to where it had to be replaced - hence the different key. I finally got around to replacing all the locks so that I'd only have one key. I started with the doors, then moved to the ignition (which I thought would be the easy part). I've replaced several cylinders before and I know it should be simple, but for the life of me I can't get the cylinder out!
I push the detent, turn the key to run, wiggle and pull.... nothing. I can feel the detent push in, and the cylinder will move a little, but it won't come out. I'm not sure if this is something that just happens sometimes and there's a fix for it, or if I'm in a unique circumstance and my column was somehow damaged during the theft and that's what's causing it.
View 1 Replies
I've got a 2014 f250 xl super cab and can't for the life of me figure out how to remove the back seat back.
View 2 Replies
How do I get the front axles out of of the knuckle? It seems like the seals are holding them in? Is there any trick to to getting them out,I am trying to do my ball joints
View 1 Replies
i have a 2008 f250 4x4 i need to replace the drive side front lower body bushing and i can not get the pressed on bushing to come out what is the easiest way to get this to come apart i tried using a 4 ft pry bar and i could not get it to pop free.
View 11 Replies
2008 6.4L F250 Crew. I just recently had a new radiator installed while the cab was off for an oil cooler change. I noticed that my lower front bushings are gone and need to be replaced.
I thought it would be an easy, pull the bolts drop the lower bushing and reinstall. Looks like they don't come out so easily. Is there a trick to getting the lower mounts/bushings separated from the uppers?
View 11 Replies
Trying to get it off. I removed four bolts nd still having trouble.
View 1 Replies
My dad has a 2008 f350 and both reading light bulbs are burnt out. How do you get the light out to get to them ??
View 3 Replies
I'm wanting to grease the center spline on my drive shaft. I got the 4 bolts off with a 12mm 16 point boxed in wrench but can't get the drive shaft loose from the rea rend. I don't blindly want to go beating it out of the yoke with a hammer to try to knock it loose (but I will if I have to). What am I missing to get this shaft out?
View 3 Replies
I need to replace the front passenger side wheel hub unit on my 2012 F250 4x4 120,000 mile reg cab truck. Its been a while but I did one on my 2000 F250 without any problems. There should be a few clips inside the hub that hold the looking hub and shaft together, right? Do I need any special tools for this job? What do the bolts need to be torqued to?
View 2 Replies
Just got my 2008 F250 SD and am thinking about removing the FX4 decal and the tinted pieces that go over the tops of the windows on the doors. Also want to remove the marker lights on top of the cab or maybe switch them from yellow to red (truck is red) so they blend in a little better. No "hate" to the folks running these options just not my style.
View 8 Replies
I have a 2004 F250 Lariat Crew Cab FX4 6-3/4' bed.
What is the procedure to remove the Driver's side Rear Sway Bar Link upper bolt? - the link attaches to the frame. The nut is on the inside of the frame with about 1/3" to 2/3" clearance between the frame and the fuel tank. Of course, the frame's "C" shape faces towards the inside.
View 1 Replies