Ford Super Duty (1999-2016) :: 2008 F250 - Blower Only Has 2 Speeds
Jan 9, 2014
Only 2 speeds of the 4 speeds are working on my blower. I was thinking it may be the switch, but someone at the shop told me to replace the blower resistor first. I did that and still only have 2 speeds. Im guessing I need to replace the switch now?
Also, I am having problems with my heat adjustment. I have it set to warm (half way between cold and hot) and out of the blue it will start blowing hot. I turn it down all the way to cold until it blows cold air and turn it back to warm, and it will be fine for a few minutes and start blowing hot again. Vacuum problem? blend door problem? How would I go about trouble shooting this problem?
View 1 Replies
My Blower motor is intermittently going on and off. After messing with it for a while it seems to stay on. Motor may be going out. Not real easy to change the blower motor on this 2008. Haynes manual says to take the 2008 and up trucks to the dealer.
2008 F250 4DR 5.4L
View 8 Replies
1999 F250 .. Blower works some times then for no reason stops. When it works, I have all speeds, it makes no odd noises. I shut the engine off and then it does not work. I have power to the blower motor even when it is not working. I doubt it is the speed resistor module because that is not used in high speed. I've taken the blower motor out of its housing and pulled the resistor module as well. I find nothing wrong, power it up and the blower works. I put it all back together and it does not work.
View 4 Replies
My dad has a 2000 f250 4x4 with the 5.4. he said his blower would only blow on high. I told him it was his blower motor resistor. i thought it was under glove box. he took it apart and said no but there was a little box thing with wires he took off anyway and put back on. I then told him it was under hood below a/c lines. he replaced old one with a new one from auto zone and replaced the pigtail( plug too) fan works on high and a little bit on low very very little when u switch it to medium it stays the same. High works great. So we replaced the fan switch. (Radio was a bitch to remove) and it still does the same thing. I checked all fuses . when I check the plug at the resistor there is power to the center pin it stays on when u switch to low and medium but when u turn high on power goes out( on test meter) is there something I am missing? the blower blows on high even when u remove the plug from the resistor. Is that normal?.
View 4 Replies
The blower motor went out on my 2008 F-350,? I can't for the life of me figure out how to get it out. Do I have to remove the dash? I am positive it is fried, I ran a hot wire straight to the motor and it still wouldn't come on.
View 2 Replies
I have and 07 F250 and the #2 speed for the blower motor don't work (hasn't since I bought it) I read that the most common cause of this is the resistor under the hood on the firewall so I replaced that and still no 2nd speed??? Where I look next? Motor itself maybe?
View 11 Replies
My HVAC blower motor stopped today while the wife was driving the F250. I thought I should swap relays (with the heated mirror relay - same Ford Part Number) to rule it out or identify it as the culprit. However, since these are close to the firewall, I have a hard time getting the grip and leverage to pull the relay out of the Battery Junction Box (BJB). How to make this a bit easier?
View 5 Replies
My blower works half of the time...from what I have researched it is more than likely the resistor. The thing is I can't find it..all the videos and pictures looks like they are the **** control control. Where this is located for the dual climate control?
View 3 Replies
Recently got a 2003 f 250 6.0 that has had a little work done on it. Absolutely love it with 1 exception. When I turn on the ac or heat It blows a 10 amp fuse that goes to the blower relay. It was occasionally now it's all the time.Blower ok, fan speed resistor ok. What or where to look.
View 8 Replies
I have a 2011 f250 6.2 cclb and it shakes around 70 to 75 mph. Not terribly but enough to annoy the crap out of me. Now I have put new tires on it recently, new Rancho 9900 adjustable shocks, I have it aligned regularly and tires rotated and balanced every 5000 miles or so. I have had two dealerships look at and my local shop and they can't see anything visibly wrong with it.
View 7 Replies
2014 F250 SuperDuty 6.2L gasser, x-cab long bed work truck. 105k miles, original owner, 1 driver, mostly highway miles, well maintained and super clean truck.
First issue occurred at 83k miles, Aug 2016. Warm summer day climbing I-70 in CO, slightly loaded, and just entered the Eisenhower tunnel (11,150' altitude). Lost power, no RPMs - not running, I put it in N and rolled as far as I could. Hazards on and no-where to pull over, hugging the wall and blocking one lane. Power OK - will crank, no fire. 1/3 tank on the fuel gauge and >100 miles distance to empty on the trip computer. Tunnel rescue shut down traffic and pushed me out into the daylight.
After waiting an hour to fill our paper work for disabling the interstate tunnel I returned to the truck which quickly started. No symptoms, no lights, no codes. Topped off the fuel tank after a easy 15 mile drive downhill. Drove another 800 miles symptom free to my destination and checked it in at the dealer. At this time a check engine light had finally illuminated - PO420. I shared the story of stalling out at highway speeds with the Service Writer. Dealer replaced the cats, confirmed fuel pressure OK, computer condition OK, serviced the trans (at my request).
No symptoms reoccurred during the next 20k miles until last weekend. 105k on the OD now. Heading to Flagstaff, AZ on I-40 in similar conditions. Hot, AC running, climbing in elevation, slightly loaded, running on the bottom 1/3 of the fuel tank... Died while cruising at 79 mph. Well, at least this time I wasn't in a tunnel and had a shoulder to pull off on. Deja-Vu - full power, radio on, no engine lights, gauges normal, fuel reads over 1/4 tank, >100 miles till empty on the trip computer - won't start. Cranks, but no fire. Some sputtering during start attempts must have triggered the next trouble code.
Opened the hood, removed the gas cap, let it vent and cool for about 30-40 mins while I took a walk. Returned to the truck which easily started and let me drive to the next fuel station, 30 miles away. This time the check engine light stayed illuminated. It took 24 gals of fuel. Drove 3 more hours and almost 200 miles without symptoms - check engine light still illuminated keeping me curious and fully alert along the way.
Got the codes pulled at a parts store that was open on Sunday. PO300 & PO301. Random misfires and cylinder 1 misfires. Sounds consistent with poor fuel supply? Spent the rest of the day searching forums for any clue to this highway stalling. All I came up with was to clear the computer - disconnect battery, turn lights on, wait 15 mins, reconnect battery, start engine, apply brake, drive, etc. This and another full tank of gas gave me enough courage to set out on my trip home.
Next occurrence was just outside of Santa Fe, NM. Similar conditions again: Hot day, AC kicking, Interstate travelling about 80mph, slightly loaded, climbing in elevation, fuel tank just below half - stalled out. Repeat previous learned routine. Open hood, vent gas cap, walk it off for 30 mins, return to truck, start it up. Drive to next town and top off with fuel about 30 miles away - only took 16 gals! Made it home 4 hours later without stopping. No repeat symptoms, no check engine lights.
The next day a code - PO420. Catalytic efficiency below threshold.
Quick recap:
6.2L gas engine stalling at hwy speeds.
Cruising between 65-80mph
-Interstate travel - no stops between last fillup and stall.
-Warm weather, AC on
-Running on bottom ~1/2 tank
-climbing in elevation, slightly loaded
To clarify: slightly loaded - no trailer, maybe 1,500 lbs bed cargo, mostly wind drag. The most I have pumped into the fuel tank is 29-30 gals or so. I assume I have the 34 or 35 gal tank. Never seen the calculated "distance to empty" below 40 miles.
View 10 Replies
My factory-ordered 2016 F250 CC SB 6.2L 4X4 3.73 is about 6 weeks old. Driver and passenger side door rattle noise (in upper back corner) at highway speeds (65-75 mph) has gotten progressively worse over those 6 weeks. See attached video.
Trying to determine if this is caused by:
Door seals: the temperature here in Iowa has dropped from a few weeks in the 90's to the now in the mid-60's.
Could the temperature change have caused the seals to change shape/structure and result in the rattle/noise?
The exterior seal between the front and back doors (attached to front of the back door): mine seems a little loose on top, but nothing that would cause this kind of noise.
View 14 Replies
My 2003 Ford F250 V10 seems to have a vibration, sometimes at all speeds and sometimes at freeway speeds. I replaced front hub assemblies and ball joints and rear calipers last year. When braking i have a vibration in rear as well, which I think is from uneven rotor but can it be causing my vibration? Also sometimes I can smell hot brakes from the rear.
View 2 Replies
My truck all of the sudden started overheating when running idle or at low speeds. No towing or anything with 89 degrees outside it can hit max water temp in matter of 2 minutes once at running temperature and standing on red light. I checked the coolant level - looks good and changed the thermostat just in case, but the problem is still happening. The fan is running/kicking in as well when it gets hot.
I'm waiting for OBD2 plug to read the stats from the computer, but what else would you suggest I can check for issues ? Oil temp gets to about 222 and transmission to about 194, but it doesn't keep on increasing. One another thing I noticed is that when I have AC running it will actually pop a overheating message on the display (I don't continue to drive it at that point) and when it gets hot it seems as if it didn't have much power.
I don't know if this is connected, but about two months ago it started blowing black smoke when starting from red light or stop sign or when accelerating with gear reduction. It is a 6.7 diesel one and only has 60k miles on it, so I'm hoping its nothing major.
View 2 Replies
I noticed a moaning from the front end a few weeks back and it seems to be slowly getting a little worse. It is only noticeable when I'm accelerating or maintain speed, but as soon as I let off the accelerator and start to decelerate, it goes away. Sometimes, when the truck hasn't been driven for at least a couple hours, I pull away and there is a really noticeable sort of "clunk clunk clunk" but then it goes away and it just moans. I can also hear some noise from the front end at highway speeds, but of course it is hard to hear much else other than engine and road noise from the cab. It's a 2003 F250 with a 7.3 and four wheel drive.
View 8 Replies
2008 F-350 ... Getting a click in the steering wheel. Slow speeds in parking lots. Even with the truck off you can manually move the wheel and notice it has play. Maybe 1/16" - 1/8" of play
Read a few old posts saying there was an TSB on it TSB 05-15-1 ... Couple of the posts say they replaced the steering column. Wanted some input before I pull this apart. It's more annoying than anything ..
View 1 Replies
Seems recently my 2008 f250 diesel wants to go into 4wd all by itself. It's the electric switch on dash with the auto/lock front hubs. I'm thinking either the dash switch or the accuator motor. Where to start though... Also I can turn the switch to 4 wheel high and it doesn't go in.
View 1 Replies
I'm having a strange issue with my 2008 F350 6.4. I have only had this truck for about 2 months now. Every time it gets wet (from rain or a carwash), the 4x4 low light begins flashing, and the truck surges badly at low speeds. When I get above about 25 MPH, the light stops, and the truck runs normally. At the next stoplight, it happens all over again. After a couple days of dry time (?), the truck is back to normal (until it gets wet again). I have found a couple of old threads involving some similar symptoms, but they were never resolved on this forum (that I could find). I believe the transfer case selector motor has been replaced at some point, as it has a Dorman brand sticker on it. I wouldn't think Ford would use Dorman parts as original equipment.
View 4 Replies
So my dad just bought a 2008 f250 xl with a single cd head unit and mp3 hookup. When you press the aux button on the head unit, it displays ' no aux audio". We have tried unplugging the radio and plugging it back in for a few minutes, but that has not worked .. Any way to get the aux input to work?
View 6 Replies
Pump works fine. Replaced pvh. Won't go into 4wd hi or lo no matter what I try. Even with them in lock. How do I know if hubs need replaced or just hub locks?
View 2 Replies
