Ford Super Duty (1999-2016) :: 2007 - Transmission Filter Part Number?
May 17, 2015
2007 F250, V10. What is the part number for the transmission filter?
View 3 Replies2007 F250, V10. What is the part number for the transmission filter?
View 3 RepliesI am not sure mine are done yet, but I was told by mechanic that they are failing and that the fronts aren't spinning as smooth as they should when up on the jack. They were investigating a sticky caliper at the time and said they believe heat from failing bearing caused that issue. I figured I'd do a little looking for parts pricing just incase. Does come with everything needed to change it? From reading, I found part # 73CZ-1104B is that the one?
View 6 RepliesI'm trying to locate the part number (and a replacement) for the plastic piece that covers the top of the tailgate (when its shut) next to the step. It's about a 12 to 16 inch long piece of plastic which has some broken tabs on it, so everytime I drop the tailgate, it either flies out or starts to... I checked the fische online and I don't even see it in the picture. I did find some one-piece parts called "tailgate spoiler cap" but I didn't find any to fit a 2014 F-250 with the step on the tailgate. Should I just tell the wife to go hot-glue it ?
View 1 RepliesI have an 2003 F250 with a nosiy alternator and need to change the bearings. I would like to have the bearings on hand before i take it apart. What is the part numbers for the bearings I need?
View 3 RepliesI'm wanting to get a single in-line steering stabilizer for my '05 F250 4x4, but I can't seem to find any that include brackets.
I don't need a dual setup because I'm not running a big lift or big tires, but I want an inline stabilizer so that I can just leave the stock one in place.
What is the part number for one that comes with the mounting brackets?
Replacing the backing plates on my rear end, figure get new inner bearings and seals in there. Bearings seem fine but cheap insurance, dont wanna pull it all off again.
When i pulled my hub off, the hub seal stayed on the housing shaft, this is normal? Just gotta pry it off there somehow?
Then new seal-TIMKEN 370247A just tap it into the back of the hub? Also is this the right inner bearings? TIMKEN NP114036
Parking brake lever for the park brake on my 2001 F250 srw. Both are rusted up but im having trouble finding the part.
View 1 Repliestime to change the tranny fluid and filters on my 2010 F250. nothing in my owners manual about this.
All the parts look up places say I need 2 filters, the internal (FT-180) and an external (FT-145).
Problem is that I cannot seem to find the location of the external filter.
Doing some research, it looks like mid-08 the external was eliminated. So, do I have just the internal or do I have the 2?
Regarding the fluid. If I use the Maxlife dex/merc that says meets the LV spec, will that be ok to mix with whatever is in there now? (assuming LV, but I bought used with 145k on it, no idea if its been serviced before and if so, with what).
Going to check with dealer about the hot flush machine, but I really doubt they have one, and I'm kinda concerned about doing a flush at 150K not knowing the history of it.
Was going to change my transmission fluid and filter today but when I got under the truck to see what tools I needed, I was not sure I could drop the pan enough to get it off.
I have a 2009 V10 4X4 and the exhaust pipe catalytic are running down each side right under where the transmission pan is. It looks like I can get to all the bolts, but because of the catalytic are right under the flange of the pan on each side, the pan will not be able to drop straight down. It looks like it may drop about 3 inches before it hits the catalytic.
Will that be enough to slide the pan forward or maybe tilt it to get it out? Has anyone dropped the pan on their 4X4 with the 5RW100? Just looking to have someone say I can get it out before I try it.
Any luck changing the external transmission fluid filter, without breaking it or its piping?
View 2 Replies03 F-250 V-8 Trition ... Once the weather gets warmer all be doing a transmission fluid exchange ...
Does the transmission have an internal and external screw on filter? Or is it just and internal? Also do I have options like a wix internal filter or just a stock replacement? Is it sealed with RTV/ or a one piece gasket?
I am swapping to a 6.0 trans cooler in my 7.3 and want to add the external filter as well. I looked through the tech folder and the link about the external filter doesn't seem to be working. I am just looking for part numbers of what everyone is using. Is the Magnafine as good as a spin on style filter?
View 11 RepliesWith an AD2 and no HFCM, need to have a part number for just the top of engine filter? All I can find (Motorcraft, AMSOIL, Racor) are the dual filter kits.
View 4 RepliesSo there I was doing a simple oil change and when I took the filter out I noticed the little spring on top, in the center of the big spring (oil filter adapter) cocked to the side with the little plastic piece broken.
does anybody know if I can replace just the oil filter adapter (spring thingy that goes in the middle of the filter when installed) or do I have to replace the whole filter bowl assembly? And if so where would be a good place to get this part?
Changing tranny fluid/filter today, all has been going great until I went to take the filter o-ring out that didn't come with the filter. It will not come out! made a hook tool out of an old tooth brush like someone on here did, o-ring wont budge. Tried a hook pick, it wont dudge (actually bent the tip on the pick and started to tear the o-ring). Everything is ready to go back together and get filled, but this stupid o-ring will not come out!
View 3 RepliesOn my previous 1992 F-350, when I serviced the E40D 2WD trans I replaced the filter during a trans service. I read about some filters falling down inside pan causing shifting issues. There is an aftermarket clip sold that holds the filter in the up position and prevents it from falling into pan.
Is the clip also used on the 2WD 4R100? is it the same issue of potentially falling down in pan as was the case with the E40D? Preparing to service my 2003 F-350 2WD 4R100 and install a new filter and want to be sure I have all parts/supplies ready to go.
After replacing fuel filter, pump relay, and air filter for good measure my 2002 f250 v10 gas engine still wont start. What to do?
View 13 RepliesWhat is the Lexus / Toyota part number for the RX 450h engine air filter?
View 2 RepliesWhat are the toyota part numbers for 2012 SE 4cyl...
1) Engine Air Filter(element)
2) Cabin Air Filter
A cab light (OEM) has burned out. I'd like to replace it. What style/part number bulbs are used?
The closest tangential reference I can find is to 194, with additional references to 168 and 912. A Google Image Search of makes it seem like I'm getting warmer.
I was just in the middle of doing the V Code leaf spring swap and noticed a broke part where the u-bolts sit and what looks to be attached to the trac bar. The piece is broken in half and I am not sure how this happened or when. The piece is welded to the axle.
2003 Excursion 4x4 6.0...