2007 F350 6.0 .. I let the truck sit for about a week went out to start it truck cranked right up then died now the truck wont start truck was running fine until this I wasn't having any starting problems. the codes are all eight injectors low circuit tested ficm had 48.3 volts...
View 1 RepliesI have a 2006 F-350. I got a code p2623 ipr circuit open. I ordered a new one and currently waiting on it. I pulled the old one and the screen has been replaced already. How often do these valves go bad? Is there anything else I should check?
View 6 Replies2007 6.0l cranks but no start. Read all the forums and I think I performed all the checks. Getting a ficm/ cam sensor/crank sensor no sync. I'm also getting 84.70% at the ipr while cranking. Do I have multiple problems? Watched videos on either the ficm or ipr percentage but not one that had both problems. Getting injector clatter and fuel pump runs. Didn't see anything obvious with the harness.
View 5 Replies2001 F250. I have had issues on other trucks where you get a funny-acting speedometer with a code that comes up as VSS (sensor on top of the rear differential)....And it shifted exact same way.
My new truck speedometer is totally fine and the ABS is on with codes:
C1158 Left front speed sensor coherency malfunction
C1155 Left front speed sensor input circuit malfunction
Shifts about the same way on the trucks with bad VSS.
Question is will a bad front speed sensor affect the way the trans shifts? Doesn't happen all the time. If you go slow it shifts smooth. If you pull off fast a barely noticeable jerk from 1-2 and 2-3....
I have a 2002 F-350, 7.3 that is not charging. It has no power coming in on the big supply lead on the back of the alt. I traced the cable back, and it goes to intake heater solenoid. Cable is good, but intake and glow plug solenoids both have no power coming to them. I am guessing there is an open circuit between solenoids and starter. My question is, does the power come right from the starter, and is there circuit protection in there someplace?
View 2 RepliesI have a 2006 f-350 6.0 and i went to fill up my truck with diesel. After that the truck did not start. Currently has the code p2285 - injector control pressure sensor circuit low. I tried disconnecting sensor, still no start.
I have the torque pro app and another 6.0 that I use for comparison. Check power at ficm 48 volt, flp 11.5v, FVP 11.5v. Hpop while cranking shows 1400 psi. removed oil filter and see low pressure oil ok, fills up reservoir. ipr at crank about 65%. fuel filter full of fuel.
Replaced the dummy plug on passenger side because originally hpop was very low psi 12. after replacement it went up to 1400 on cranking. What should I be looking at next, should I be removing ipr? should i be looking at crank sensor or cam sensor? Just installed 2 new batteries also because my dad kept cranking the truck until it died.
Checked to make sure fuel cut off relay not triggered, Ok. The truck has been having long cranks before it died. Also right now the injector cycling is 10 seconds long while on my other 6.0 it is about 4.
2003 f350 2wd 5.4 auto cab and chassis with 40 gal rear tank replaced fuel pump/fuel filter/spark plugs/IAC no codes
View 7 RepliesI have a 2013 F350 Crew Cab Long bed xl with 128000 miles on it. I just barely bought it from a small dealer and had a check engine light come on for the cats.(P0420 and 0430)
I have spoke with the dealer and he assured me that he would replace the cats. He stated he had O2 sensors replaced and thought he had fixed the problem. Not sure if he replaced all sensors or just the fronts.
He has been avoiding calls lately and will not return my messages. Anyways, My question is what should I be looking for to prevent future cats from going bad. I just ordered a bluetooth OBD 2 scanner and bought the Torque Pro App.
I am not new to working on trucks but they have all been 1995 and older and i am new to anything scanner wise and do not know what I should be monitoring. If I can't get this guy to replace the cats I want to monitor everything to make sure the cats are bad.
BTW, Fuel Mileage is at best 12.3 with an extremely light foot, Driving normal it drops off to about 11.8-12. Is this a normal MPG in these trucks? I have seen post about people getting close to 16 unloaded not smashing throttle?
On another note, I just remembered that my traction control light will come on with no wheel spin at times after starting the truck and driving away.
I just recently purchased a 2008 ford f350 5.4L gasser, supercab long box. The truck has 167,000km on it. I flew about 700km from my hometown to pick up the truck and drive it home. After driving about 300km I started noticing a few problems.
The engine light codes that have been stored as of now:
P0420 (Catalyst code)
P0420 (Catalyst code)
P0191 (Fuel rail pressure sensor i think?)
The issue I'm having is that the truck has absolutely no power going uphill or accelerating. If I'm climbing a hill and have the gas pedal pushed in at a steady rate its almost as if the transmission wont shift, and if i push harder on the gas the truck begins to shudder. When the truck is cold it runs normal and climbs hills no problem, but once it heats up the problem returns. Another odd thing I noticed under the hood on my drive home was that they disconnected the vacuum line from the fuel rail pressure sensor and simply plugged the line on a random bolt.
Also, the truck apparently has a cam phaser lockout on it and I dont know if that could be causing the issue? Here's a list of some of the troubleshooting ive done so far.
-checked all fuses(start at the basics eh)
-checked resistance of coils(checked out fine, even after engine was warm)
-pulled spark plug 1 and 5, they both seemed fairly clean, not fowled up
-generally looked over all the vacuum lines, seemed fine couldn't see anything else really out of the ordinary
-while the truck was running I used a temperature gauge to see what the exhaust system was doing. On the drivers side when the truck was warm before the cat I had 140C and after the cat it was 80C(good indication the cat is plugged?) The other side tested fairly consistent.
My dads truck started misfiring last week, first thing i did was scan the codes and got p0303, p0304, p0305, p0306, and p0308. Its an 08 F-350 5.4...already changed out the spark plugs and the same codes came back. I decided to do some further testing and so far all coils had spark as well as 12.4 volts going to each. I did check the switching signal and that was present as well.
Moved on to the injectors and i checked each connector with my noid lights and it flashed on all cylinders. Did a resistance check on each injector and they all registered 12.4 ohms. We did switch some coils around and all the same cylinders misfire. My next step is to do a compression test.
My biggest question is if there are any common problems with these engines besides the coils, by the way this truck has the brown coil boots and the spark plugs that dont break in the engine.
Have a an 11 f350 6.2 gas throwing p0171 and 0174. Driving the truck it has spark knock pretty bad. Ive parked it at this point. Its a tow truck so I need it fixed and back on the road. I've checked the hoses going to the pcvs they appear to be ok.... Also upon starting the truck it just sounds weak.....
View 1 Replies I bought this truck (2011 F-350 6.2l) used a month ago with 125000 miles on it. Of course the MIL light came on as soon as the ink dried. The codes read PO420 & PO430 and my local Ford Service said replace the cats. I said what is the cause of the failure, ford said here is a list of possible causes but it's not reading other codes so they don't know what caused the failure.
Well, I went ahead and replaced both catalytic converters, all four O2 sensors, and I replaced all sixteen spark plugs. Guess what, the MIL light is back on not 24 hours later reading PO420, PO430, and now PO620 and PO645. So I just went back to Ford today and all they did was cleared the codes and told me to call if the light comes back on. They said my PCM is up to date but why it's now reading GENCOM code or AC Clutch code.
I have a 2006 F350 SRW 4WD 6.0 with 127000 miles on it. A couple of weeks ago it, pulling out of my driveway, it hesitated and tow haul started flashing. I had codes pulled and it showed P1780, P0751, and P2700. After turning off, codes were gone and tow haul off. Ran fine since then every day. Yesterday while going about 50 mph it started acting like it was in neutral (revving up), nothing happened when mashing the accelerator. Coasted to a driveway and truck would not move, only sounded like it was in neutral.
View 1 RepliesI own a 2011 F350 dually with the 6.7 in it. It has 136000 on it and zero mods. I was driving over the weekend and the traction control light, brake light, and the ABS lights all came on and the information center displayed Check Brake System. We were towing our 5th wheel when this happened. The brakes on the pickup and trailer both work and we have no problems stopping. About every 15 minutes or so this message pops up and it chimes again. My insight is reading a U0418 code. We are stopped now and the code and alert message is still popping up without the trailer. All fluid levels are where they should be.
We are also getting a check engine light and my Insight is reading the codes P2020 and P20E8.
I can reset the codes dealing with the reductant leakage and low pressure, but not the codes dealing with the brake system.
I have had my pickup in to 2 different ford dealers for these issues and they cannot find anything wrong. I did notice that this time when the Check Brake system warning appeared that the pick up started lunging a bit, we lost power to the stereo and the windshield wipers came on. Our fuel mileage has remained the same and the pickup still tows like a beast.
I have a 97 F350 5.8 with E40D trans. I bought the truck with it shifting hard thinking maybe a simple filter/fluid change would fix it. It may have worked a little but did not fix the issue. There were 3 or 4 codes that I have already cleared up with new parts. I am still getting a 327 (something with EGR?) and 629 (Converter clutch control circuit failure). These show up in KOEO and KOER self test. The O/D does not flash ( bulb does work).
Parts that have been replaced: VSS, MLPS, new connector going into solenoid pack (tabs were broken), TPS. Removed the trans wiring harness and there is no damage or loose connections. When I replaced the solenoid connector I noticed there was some trans fluid in the connection. I cleaned it the best I could and reinstalled with dielectric grease.
The truck runs fine and shifts in and out of every gear fine its just shifting hard. If I unhooked the battery it will shift perfect for 5-10 minutes but then the hard shifting returns.
The only other thing I can find with my research is maybe the solenoid pack needs replaced. I figured if I take it somewhere they are going to want to rebuild/replace transmission. It seems like it can't be something very major since it will shift fine when reset...
I have a 2003 f350 v-10 drove it yesterday to get fuel, went to start it after fueling. No start, no lights dash was gauged was acting odd, and clicking under the dash from behind fuse box. did get it to start after a while, put my foot on the brake to go into drive, never made it ... truck died I do have remote start system thought it was that with the brake pedal issue. disconnected complete system. no change. Had it towed, home now no nothing, connect a battery and just clicking from under dash no start ?????? not a battery, won't even jump. The battery is good, power to starter, Posted this also in light-duty trucks wrong place think this is the better place. Gauges pinned to right with key off
View 3 RepliesI just bought a 2007 f250 5.4 V8. It has the codes P0018, P061b, and P2106. The truck seems to run fine but has the codes. Tried clearing but they came back. Also, there's a small howl sound in the rear end. What a solution may be.
View 14 Replies2007 F-350 4X4 King Ranch... I have the 6.0 diesel. I am on the road to Houston, Tilden and San Antonio TX, and I am noticing a whistle on acceleration. I can change the tone by how hard I push down on the accelerator. I thought it was a radio issue and turned the radio off and got no change. Turned the a/c off, no change. Down hill or coasting, nothing.
View 3 RepliesOn my 2007 f350 when I hit my brakes it pulsates... So I put new rotors and brakes up front.. The pins are good and the calibers are good... put it all back together and still the same thing... the slower you go the slower the pulsating gets... And I can actually feel the pedal move in and out when it does it... I'm lost....
View 14 RepliesMy truck was running fine, it's stock as far as I know. Shut it off, it sat and cooled off for a while. When I tried to crank it, it wouldn't start, threw 2 codes. P2285 and p 2623. I unplugged the icp sensoran tried to start, no start. Plugged it back in and it started fine for the rest of the work day ( I work out of it). Drove it the next day without any issues. Today went to start before work and no start with the same 2 codes. What should I check first? I don't have any monitor yet. Bought the truck a month ago as a work truck. It has 164000 miles.
View 4 RepliesI have 99 f350 single rear wheels 4x4 . I went to start it this morning and it would crank but not start b/c it was cold. I plugged it in and still wouldn't start then it wouldn't even crank. I checked all fuses swapped relays and I have new batteries. The last thing I did was hit on the starter a few times and it started. So I went and bought a new not remand a new starter and put it on and now it won't crank!? I get 12v at the little wire on the selenoid on the fender. So now what?
View 4 Replies