On my 2007 f350 when I hit my brakes it pulsates... So I put new rotors and brakes up front.. The pins are good and the calibers are good... put it all back together and still the same thing... the slower you go the slower the pulsating gets... And I can actually feel the pedal move in and out when it does it... I'm lost....
View 14 RepliesI have a 2007 F350 XLT, Super Cab, chassis cab, V-10, 4x4. I ordered it new, it now has 97,000 miles. It is equipped with a 9' aluminum flatbed. I tow it behind my motorhome and also carry a truck camper (not when towing it!).
I don't think the front brakes are working 100%. I have 2 sets of wheels and tires (19.5s for hauling the camper). Every time I change over, I check the brake pads for wear. Over the first 80,000 miles there was very little wear on the rear pads. In 2014 I had almost a complete brake failure while traveling. I took it to a Ford dealer, and they determined the brake booster was bad. They replaced the booster and flushed the brake system. I didn't think the brakes felt right afterward, but I carried on. By 95,000 miles, the rear brakes were worn out. I feel like the rear brakes are doing most of the stopping now, thus wearing out much faster than they were.
I just ordered a set of service manuals for the truck (9.5 years late on that!) hoping to figure out something. I like the truck, it meets my needs, and I hope to keep it quite a while longer. I took it in to the local dealer to replace a leaking rear pinion seal. They found and replaced the worn pads. I trust them to the extent that the pads were worn, as I had already noticed an acceleration in wear. Local dealer that replaced the pads has no idea what could be up. They did clean and lube the front calipers at the same time, but I noticed no difference in brake feel. Stopping power is definitely worse than before the brake failure/ booster replacement.
What might cause this? The only things that come to my mind is a problem with the proportioning valve or maybe the master cylinder. I don't know much about the details of the ABS system. Is there anyway that might be causing the issue? I would rather not just start throwing parts at the problem...
Got a problem with my F350 diesel truck's braking system. I pull a 5th wheel and last trip almost burned my breaks up coming down long hill due to having no breaks on the 5th wheel. Had a problem early on with the lack of trailer brakes and module was replaced under warranty. Bought a new module this time and it did not fix the problem. Have braking power when I use the module brakes (Hand) but not when I hit the foot brakes. Have checked the system with a meter and have good voltage with hand break but not with foot brakes. Have a good meter (voltage) read with hand breaks and faint read with foot brakes applied. Also have a faint pulsing read on test light with no brakes at all just key on.
View 2 RepliesWe have a 1994 350 ford dually. the brake light and the abs light came on and it has no brakes. replaced the master cylinder ... still no brakes. what next?
View 1 RepliesI just changed all the pads and rotors on my 08 F350. The brakes are much better now, only the rear brakes got quite hot after driving it for about 15 min. Turns out the rear parking brakes are dragging on the back brakes. I adjusted the parking brake on both sides so they no longer drag and the heat issue is gone. The problem now it the parking brake does not engage until the pedal runs out of travel. Any tips to get this just right? Will the parking brake self adjust like the old drum brakes and shoes use to do years ago?
View 7 RepliesI have a '03 F350 that I can't seem to solve the brakes vibrating when applied. Replaced front rotors a couple weeks ago. I still have a vibration when I apply the brakes. What am I missing? I didn't replace the back rotors, but maybe I should have. On the passenger front, the inside pad was almost gone and the outside pad was in good shape. I greased the pins before I replaced the pads the last time, but the inside still wore much faster. I also blew out the rear brake line last week and spent Saturday bending a new line and replacing that so the brakes were bled when I had to replace that. I don't feel the pulsing in the pedal, but the truck shakes pretty good when I hit the brakes. What else should I be checking if the rotors are new and the pads are new and the pins have been lubed and the brakes have been bled?
View 6 RepliesI just can't seem to make sense of, 2006 f350 6.0 once it's been running for a min or so it will die when brake is pressed, also dies when you turn the wheel. Can't find any rub through or bad wiring.if you up rpm slightly it will not die with brake or steering. Tried removing belt thinking it possibly was a pulp and it doesn't die with the brake or steering but will die when going from drive to park. Thinking possible cps....
View 13 RepliesI have a 2011 F350, with a 4 inch Rancho Suspension lift. Ever since the lift kit was installed, more commonly when turning to the left than right, the anti lock brakes come on and the traction control light comes on/flashes. without even stepping on brake pedal.
It seems to happen when the wheel is at about 80% of max turning, about 15mph. Both wheel hubs and sensors have been replaced. road tested with Ford tech , he watched the speed sensor input while hooked to the computer and all sensor are reading correctly.
Today I went in a constant circle and can make it do it non stop, and when you try to press the brake pedal while the anti-lock (grinding/chattering) noise is happening, it only gets louder.
Every time I apply brakes I hear a weird humming noise, as well as no stopping power. Checked fluids and pads and everything is where it should be. I heard abs can cause this but not sure on that. I know my master cylinder has a very small leak but it hasn't lost any fluids of that sort. I'm lost. I don't know where else to look.
View 2 RepliesI have a 2002 ford f350 triton 5.4 V8. I just put front brake pads on my truck today. Started driving around and i could smell burning brakes. Stopped and alot of smoke was coming from my brakes on my front passenger side but nothing from the front drivers side. Replaced all the brake pads on the front. What is making them so hot?
View 8 RepliesI've noticed when I'm towing, on long down hill grades if I touch the brakes I get what feels like a rotor causing the steering wheel to shake. At first it was only mild, but today on a long 6% grade it got really bad. Never does it on a level road, I've tried to duplicate it, only on a long down hill grade, and I'm not getting a pulse in the brake pedal at all, only the shake in the steering wheel. It's probably time to replace the pads anyhow, and I'll check the rotors. What things to look at?? 2006 F350, 6.0 dually 4x4.....
View 2 Replies2011 F-350 XL, I can hear a squeal coming from the front brakes when rolling forward slowly, believe the pads are dragging on the rotors. If I touch the brake pedal the squeal stops as it does when I turn the wheel. Took the calipers off and greased the slide pins and put it all back together, still got the squeal. What don't I know???
View 9 Replies2007 F-350 4X4 King Ranch... I have the 6.0 diesel. I am on the road to Houston, Tilden and San Antonio TX, and I am noticing a whistle on acceleration. I can change the tone by how hard I push down on the accelerator. I thought it was a radio issue and turned the radio off and got no change. Turned the a/c off, no change. Down hill or coasting, nothing.
View 3 Replies2007 6.0l cranks but no start. Read all the forums and I think I performed all the checks. Getting a ficm/ cam sensor/crank sensor no sync. I'm also getting 84.70% at the ipr while cranking. Do I have multiple problems? Watched videos on either the ficm or ipr percentage but not one that had both problems. Getting injector clatter and fuel pump runs. Didn't see anything obvious with the harness.
View 5 RepliesI have the ford upfitter switches in my 07 f350 and i had two flashing lights wired to switch 4 (10 amps) for snow plowing. The lights were LED and shouldn't have drawn much power but suddenly the lights stopped working because thers no power going to the fourth switch. They work on all the other switches. What could be the problem?
View 5 RepliesI have a 2007 f-350 with the 5.4. The fuel pump is not running, have voltage at the inertia switch but none at the pump. Where the pump driver module is located at?
View 2 RepliesI have a 'new to me' 2007 F-350SD super cab and need to run some wiring inside. What I don't know is how the heck the trim pieces are attached and how to remove them without breaking them! If it ain't held on with screws, nuts, bolts...
View 2 RepliesI have a 2007 f350 scsb with the 6.0 that has 131k miles on it... I bought it in December at 125k and since I first got it I've noticed a lot of steering play at highway speeds only... Basically 60 mph and up... I have a hard time switching lanes and passing because it's very unpredictable just how the truck will behave... It feels like the steering is loose but also slightly delayed and when I make slight adjustments it feels like the truck overcorrects itself... Could this be a steering box issue? A power steering issue?
View 7 RepliesI just picked up my 2007 F350 as a replacement for my 2003 F350 (still have the 2003). I really like the uplifter switch option on the truck, I can normally figure things out but I am one of those people who is electrically challenged (home and auto)and also am one who does not wish to butcher the new ride (same for the home)to gain an education in the art of wiring. I would like to reinstall my headache rack lights on this truck as they are needed for winter work. I was in my truck manual and the info for wiring is weak and the website did not respond nor did my email to ford. I have found the wire harness but it is not tagged as a pair/color to switch. I have the lights already grounded to the rack, so I am thinking I just need the hot wire from the switch. Looking for the color code for positive and ground for the switches.
View 14 RepliesMy question is my abs light came on so I stuck my computer on it. Said right rear , we'll we all know on a 2007 6.0 f350 4X4, the there's only one sensor on the pumpkin, so I replaced it and cleared the code. Abs light came back on once I started driving, week ago my right front caliper stuck and got very hot, could that read bad for the rear of the front went bad? Will pull plug and make sure I didn't bend any pins.
View 2 Replies2007 F350 6.0 .. I let the truck sit for about a week went out to start it truck cranked right up then died now the truck wont start truck was running fine until this I wasn't having any starting problems. the codes are all eight injectors low circuit tested ficm had 48.3 volts...
View 1 Replies