Have a 2007 F250 6.0 diesel with the standard issues including misfire at highway speed. Assume the bulletproof kit also cures the stiction problem? in reviewing the threads and looking at the vendors, references are made to fixing the oil cooler issue, egr issue, etc., but no one addresses stiction issue directly.
View 10 RepliesI have a 2006 f250 and the heater will blow cold air unless you are driving in like highway conditions. If you stop or drive slow it blows cold air only. What is causing this???
View 3 Replies07 f250 has a shimmy from the rear at highway speed. Has new tires is worse with a load. What am I missing here?
View 3 RepliesI have a 2007 f350 scsb with the 6.0 that has 131k miles on it... I bought it in December at 125k and since I first got it I've noticed a lot of steering play at highway speeds only... Basically 60 mph and up... I have a hard time switching lanes and passing because it's very unpredictable just how the truck will behave... It feels like the steering is loose but also slightly delayed and when I make slight adjustments it feels like the truck overcorrects itself... Could this be a steering box issue? A power steering issue?
View 7 RepliesI have been reading several past post regarding the misfire while in OD and going up a small hill with light acceleration around 45 to 55 mph. Everything points to the COP so I replaced it today. Still getting the code after 20 minutes of driving around. My truck shudders and looses power. I can either let up on the throttle or hammer down on it to eventually smooth it out and everything goes back to normal.
Check engine light flashed but didn't stay on. My scanner does report misfire on cylinder 7 (P0307). Haven't owned this truck very long so I don't know much of it's history except OASIS report shows nothing alarming. Guess next step is a new set of plugs.
Another first today, is the tachometer is stuck at 4500 rpm. Shut the truck off and let it sit for an hour, then went back to start and tach. acts like 4500 is the new zero and running engine at 1000 rpm now indicates 5500. 2007 F250 SD 5.4 ....
I have and 07 F250 and the #2 speed for the blower motor don't work (hasn't since I bought it) I read that the most common cause of this is the resistor under the hood on the firewall so I replaced that and still no 2nd speed??? Where I look next? Motor itself maybe?
View 11 RepliesThe other day I pulled into the parking lot put it in park and let it idle for a couple minutes, it stumbled and when I started driving off it was missing. I pulled the valve covers off and check the connection.. I drove it home and it had a bad misfire at 1500 RPMs. The truck shook violently at that RPM but when I got it up over 2000 smooths out..
View 1 RepliesI have a 1999 f250 v10 auto. It has 3 miss fires thats im stumped with .. Ive replaced all spark plugs, all coils , I've had injectors out and were cleaned and it still miss fires. I can disconnect the coil and injector on the cylinders and the motor runs the same. Ive swapped the coils and injectors around to make sure it wasn't them. What else could it be? Frustrated I've had the truck for 2 years and haven't figured them out. Ive had them go away for at most a day. Also the truck has a shake at 80 kmh not sure if its from the miss...
View 13 RepliesHow to diagnose misfire with no CEL? 2001 F250 5.4. What could cause it?
View 13 RepliesI have a 2011 f250 6.2 cclb and it shakes around 70 to 75 mph. Not terribly but enough to annoy the crap out of me. Now I have put new tires on it recently, new Rancho 9900 adjustable shocks, I have it aligned regularly and tires rotated and balanced every 5000 miles or so. I have had two dealerships look at and my local shop and they can't see anything visibly wrong with it.
View 7 RepliesI have a question about my 2001 Ford F250 and the scary road sway I experience on the highway.
I thought it was the garbage and nearly bald tires and the fact that the fronts were bigger than the back, (Previous Owner). I went and got new E rated 265's from Discount Tire.
It actually made the swat feel worse. I thought maybe the tire guys inflated them all to 80 PSI as the sidewalls indicated. I check today and found that they went with the recommended PSI on the door sticker. 60 Front and 80 rear. But this is for the Tire size listed on the sticker.
After the tires cooled here at home I increased the PSI to 80 all the way around. I am having trouble finding my specific problem even though there is a lot of talk in many forums about this issue.
If this does not work should I try lower PSI in the rears and leave the front at 80? Should I try a front steering stabilizer shock? I did tighten up the steering box and took the minor slop out of it, Not is just makes it respond to the sway correction quicker.
OK, quick question. I have an '03 250 with the 5.4 and the OD light began flashing tonight. I looked in the forums here and everyone say's new tranny or sensor but over on the diesel forums the are saying that the alternator is a big cause of this (dirty power).
At the beginning of this year I noticed what I assumed to be a misfire when putting the motor under a load. Once up to speed it would smooth out and all was good. I was told that a plug job on these trucks is hellish and expensive since a lot of guys break the plugs off in the block. I put it off and the issue went away when the weather warmed up.
Now it's getting cold again and the misfire is back. Driving home tonight the truck died at a light. I restarted it and as I accelerated I noticed a difference in the shift from first to second and then saw the OD light blinking.
Again, the diesel guys are all talking alternator so my question is this: could the alternator cause both the OD light to flash AND the misfire? If the "dirty power" can cause the tranny to fall in to safe mode, can it also cause the ignition to be problematic?
My 5.4 F250 with 200,000 miles having many problems... It all started a few months ago, when the cam needed to be replaced, and a cam phaser was also replaced at the same time. It ran fine after, then threw a code for cylinder 3 misfire. The guy I took it to said it was due to the huge crack in the exhaust manifold and that was messing with the o2 sensor coming up as a cylinder 3 misfire. So, got the new manifold and it was good for a few weeks.
Now, starting the other night, Friday the 13th, it threw a CEL when I was coming into the driveway. It had been throwing a code every once in a while, and I brought it to school to scan it Friday the 13th but there was no code. So, I assume that it is an intermittent problem, no big deal. When I go to get in my truck to go to work a few hours later, the 5.4 cranks... and cranks... and cranks.
I get it to fire up, and it dies again. Run codes, and it says that the cam positioning sensor is broken. Replace both of them, still acts up ie. doesn't start when it does start it runs very rough and stalls. Get it up to my uncles shop, and replace fuel filter.. Still runs like trash. Run codes now, and it says rich/lean in bank 1.. My uncle tells me to move my truck out of the shop, so I start it up, and it runs great. No hiccups, it idles perfect as I move his truck out of the shop first.
I park my truck outside and let it idle for about 10 mins, and when I come back out it is still idling, perfectly fine. I get in, put it in reverse, and get about 20 feet when it dies and will no longer start back up. What could be going wrong?! Sick of throwing money into this thing! At one time while started up in my uncles shop, it was blowing black smoke, as if it was a diesel!
OK, not sure where to start so here goes. I have an 02' f-250 with the v-10. I just had some minor front end body work done and when I got it back I noticed that it just didn't feel right while driving. When I start it, I notice a small misfire while I stand next to the exhaust outlet. Nothing too bad, still runs great. Shortly thereafter I started noticing a more habitual missing while driving. Roughly between 30-40 mph and around 12-1500 rpm the truck feel like the driveline is about to pickle fork the truck. If I let off the gas or step on it, the vibration goes away. And very intermittent.
It will only do it when the truck is warmed up. If I only drive about a mile, it won't do it, yet if I turn around and head back, there it is! Now the weird part. I for reasons I won't get into, I left my ignition on and drained the battery. I just replaced it and for the last 2 days nothing. Nt even a misfire. Now today here it is again. I have read all over the forums for this exact problem and cannot find my exact problem. I have replaced the plugs with Autolites and cleaned the coils as well as the boots and applied a small amount of dielectric grease to the top of the plug. The boots are cleaned and not a sign of cracking or wear.
I replaced the PCV valve and nothing. All the plugs looked exactly the same. Light chocolate in color. Not one looked different than the other. I took them out again last week to verify the plugs weren't bad and the new ones all looked the same as well. I cleaned the MAF sensor also. Just cannot figure out what could be doing this all of the sudden. I don't see where anything wasn't plugged back together when it was being worked on and why would a new battery make it go away for a short time? Oh, and lastly, I have a superchips programmer that came with the truck and there are no codes showing and my check engine light has never came on yet.
2014 F250 SuperDuty 6.2L gasser, x-cab long bed work truck. 105k miles, original owner, 1 driver, mostly highway miles, well maintained and super clean truck.
First issue occurred at 83k miles, Aug 2016. Warm summer day climbing I-70 in CO, slightly loaded, and just entered the Eisenhower tunnel (11,150' altitude). Lost power, no RPMs - not running, I put it in N and rolled as far as I could. Hazards on and no-where to pull over, hugging the wall and blocking one lane. Power OK - will crank, no fire. 1/3 tank on the fuel gauge and >100 miles distance to empty on the trip computer. Tunnel rescue shut down traffic and pushed me out into the daylight.
After waiting an hour to fill our paper work for disabling the interstate tunnel I returned to the truck which quickly started. No symptoms, no lights, no codes. Topped off the fuel tank after a easy 15 mile drive downhill. Drove another 800 miles symptom free to my destination and checked it in at the dealer. At this time a check engine light had finally illuminated - PO420. I shared the story of stalling out at highway speeds with the Service Writer. Dealer replaced the cats, confirmed fuel pressure OK, computer condition OK, serviced the trans (at my request).
No symptoms reoccurred during the next 20k miles until last weekend. 105k on the OD now. Heading to Flagstaff, AZ on I-40 in similar conditions. Hot, AC running, climbing in elevation, slightly loaded, running on the bottom 1/3 of the fuel tank... Died while cruising at 79 mph. Well, at least this time I wasn't in a tunnel and had a shoulder to pull off on. Deja-Vu - full power, radio on, no engine lights, gauges normal, fuel reads over 1/4 tank, >100 miles till empty on the trip computer - won't start. Cranks, but no fire. Some sputtering during start attempts must have triggered the next trouble code.
Opened the hood, removed the gas cap, let it vent and cool for about 30-40 mins while I took a walk. Returned to the truck which easily started and let me drive to the next fuel station, 30 miles away. This time the check engine light stayed illuminated. It took 24 gals of fuel. Drove 3 more hours and almost 200 miles without symptoms - check engine light still illuminated keeping me curious and fully alert along the way.
Got the codes pulled at a parts store that was open on Sunday. PO300 & PO301. Random misfires and cylinder 1 misfires. Sounds consistent with poor fuel supply? Spent the rest of the day searching forums for any clue to this highway stalling. All I came up with was to clear the computer - disconnect battery, turn lights on, wait 15 mins, reconnect battery, start engine, apply brake, drive, etc. This and another full tank of gas gave me enough courage to set out on my trip home.
Next occurrence was just outside of Santa Fe, NM. Similar conditions again: Hot day, AC kicking, Interstate travelling about 80mph, slightly loaded, climbing in elevation, fuel tank just below half - stalled out. Repeat previous learned routine. Open hood, vent gas cap, walk it off for 30 mins, return to truck, start it up. Drive to next town and top off with fuel about 30 miles away - only took 16 gals! Made it home 4 hours later without stopping. No repeat symptoms, no check engine lights.
The next day a code - PO420. Catalytic efficiency below threshold.
Quick recap:
6.2L gas engine stalling at hwy speeds.
Cruising between 65-80mph
-Interstate travel - no stops between last fillup and stall.
-Warm weather, AC on
-Running on bottom ~1/2 tank
-climbing in elevation, slightly loaded
To clarify: slightly loaded - no trailer, maybe 1,500 lbs bed cargo, mostly wind drag. The most I have pumped into the fuel tank is 29-30 gals or so. I assume I have the 34 or 35 gal tank. Never seen the calculated "distance to empty" below 40 miles.
My factory-ordered 2016 F250 CC SB 6.2L 4X4 3.73 is about 6 weeks old. Driver and passenger side door rattle noise (in upper back corner) at highway speeds (65-75 mph) has gotten progressively worse over those 6 weeks. See attached video.
Trying to determine if this is caused by:
Door seals: the temperature here in Iowa has dropped from a few weeks in the 90's to the now in the mid-60's.
Could the temperature change have caused the seals to change shape/structure and result in the rattle/noise?
The exterior seal between the front and back doors (attached to front of the back door): mine seems a little loose on top, but nothing that would cause this kind of noise.
I have a 2005 F250 with the 5.4. This truck has been one thing after another, as you can tell from my other posts. The problem this time is, if it cranks hard to start because it's cold(can be anywhere from as high as 32, but usually in the teens) it will start just fine, then several minutes later throw the check engine light. Put the scanner on, like clockwork, 4 codes, always cylinder 1 misfire pending, misfire on first 1,000 revolutions pending, cylinder 1 misfire confirmed, misfire on first 1,000 revolutions confirmed.
Sometimes you can hear a slight lope in the idle when it does this. Clear the codes, runs perfectly fine. It will never do it after it's been started for the day. Some days you would think for sure it would throw it when it's frigid and the winds been blowing on it, it doesn't bother, other days you wouldn't think it would, and it does.Can the computer think that since it didn't start right up, it misfired?
Truck Specs:
2008 f250 super duty 5.4l
78xxx miles
4x4
Automatic
Issue:
P0300 (random misfire detected)
P0307 (cylinder 7 misfire)
Let's start from the beginning...
I was getting the notorious 5.4l ticking sound. After doing research on this issue. I found that it could be a few different issues including:
Cam Phasers
VCT solenoid(s)
Loud injectors
Valves
Exhaust leak
Loose spark plug
The list could possibly go on, but these being top concerns or issues to look into.
I took it to my mechanic and wanted him to research the ticking problem. This was my primary concern due to it was getting worse over time. I didn't want to do more damage than what was possibly already done. I told him to go ahead and change the spark plugs while you're checking into what's going on. (I know those plugs can break and I didn't want to do that.)
At any rate... the plugs got changed to motocraft brand (I know the trucks can be finicky with the parts you put back into them so I went with the motocrafts to avoid any complications.) After the plugs were changed, he told me that the ticking was caused from a blown exhaust manifold gasket (yay me... not internal parts or anything too serious. Sweet!)
I had to reschedule to get the gasket done, but knowing what it was now I wasn't too concerned about driving it. So I did. The new plugs are also in the truck at this time. I drove it the next day and right away.. I noticed a misfire. Thought maybe the plug was bad. I told my mechanic about it and he said... Sounds like a COP to me.
So I get a new COP. Okay.. easy fix. Installed it and still got a misfire. Told my mechanic and he said get another COP. So I'm thinking.. "Okay.. get a new part to fix a new part.. sounds logical.. lol" so I do what he thinks might be best. I replace the COP with another new one and it's still misfiring. The new cops are also motocraft brand as well.
Okay... next step.. he claims it may be a VCT solenoid issue. At this point I don't care.. I just want my truck fixed. So he replaces the driver side solenoid. Still misfiring..
So after doing some research on the scanner... we locate some issues that are the exact symptoms I'm having. Misfire.. at low rpm.. during cruise control.. and a sudden at idle.
This information states for this drivability issue.. to spray injector cleaner/carb cleaner into the engine and possibly clean it out. Makes sense. He did this as well as changed the fuel filter. Also did a pressure test on the injectors to make sure they were good. They were. After spraying and cleaning it out, it was taken for a test drive and it seemed okay... but not perfect. The next day.. the misfire came back.
He said that if the misfire returns, that I need to contact the dealership and see if there is a pcm update. The dealership said there probably is but can't tell me until the computer is hooked up to it. (Of course there is a charge when it's hooked up) again.. whatever.. I just want it fixed. The truck is scheduled to go in next Wednesday for that. If that doesn't fix it, my mechanic said cam phasers possibly bUT still not sure for sure..
I have a 2006 F250 5.4L. I was getting a noticeable misfire after not driving the truck for a while. Mode 6 revealed that cylinder #8 was misfiring.
I took off the coil/boot and there was coolant on the tip of the boot and some at the bottom of the spark plug well.
I cleaned everything up and put everything back together and that took care of that problem when I started the car. I also stuck a wad of paper towel by the intake manifold nearest spark plug number 8 and tightened the manifold bolts down a little. Some of them were not as tight as others.
I went back today and started the vehicle and it has the same problem again!
I took a look at the paper towel and it was totally dry! There is no coolant around the top of the spark plug well - only in the bottom of it. Where is this coolant even coming from? There are no coolant lines near cylinder #8. Is this a head gasket leak?
I have taken a look at the head gasket and that doesn't seem possible since the head gasket does not seal around the spark plug well at all as far as I can tell.
I have a 2002 F250 CCSB Lariat 4x4 with the Triton V10, I'm up to 232,000 miles so far and fairly happy with the old girl. Just this weekend, I noticed some hesitation when at idle and even more rough running when under slight load. The misfire/hesitation is worst when going up a slight hill, when the truck is accelerating at low RPMs.
I am getting zero trouble codes or freeze frame conditions on my scanner. What should be my order of diagnosis? Vacuum test at line from PCV to TB, COP test? EGR inspection? Plug inspection? Also, how do you test a coil if resistance is not a reliable method?
I noticed a moaning from the front end a few weeks back and it seems to be slowly getting a little worse. It is only noticeable when I'm accelerating or maintain speed, but as soon as I let off the accelerator and start to decelerate, it goes away. Sometimes, when the truck hasn't been driven for at least a couple hours, I pull away and there is a really noticeable sort of "clunk clunk clunk" but then it goes away and it just moans. I can also hear some noise from the front end at highway speeds, but of course it is hard to hear much else other than engine and road noise from the cab. It's a 2003 F250 with a 7.3 and four wheel drive.
View 8 Replies