2007 F250 4WD 5.4l ... when I turn sharply in either direction I am getting a light clunk sound similar to when you are in 4WD on blacktop and try turning. The engine also seems to wanna stall when I cut the wheel too sharp.
View 4 RepliesI have a 02 F250 4x4 5.4. As I drive and when pulling into a driveway I hear a clunk that can be felt in the floor and the steering wheel. I've replaced the wheel bearings and seals, shocks, ball joints, sway bar links and bushings, tie rod ends at the gear box and "right hand inner". The other two tie rods are tight and so is the track bar. I cannot duplicate the sound if I jack it up and move parts around with a pry bar. I can however move the steer box sector shaft upwards about an 1/8. I've adjusted the screw but it didn't do anything. Could it be the steer box or the springs? I've even mounted a GoPro underneath but everything moves and I can't tell why it is.
View 14 Repliesmy 1992 BMW 3-series makes a horrible noise when I turn the wheel sharply in either direction. the noise however gets better as the car warms up, and after half an hour of driving has gone away. if I turn the engine off for an hour and start it up again, the noise is back. my sister think it's the steering column. my brother-in-law thinks it's the power steering pump, or some kind of really complicated switch to do with RPM that I don't understand.
View 1 RepliesYesterday I was parked on an incline with my front wheels on gravel and the rear wheels on wet grass/mud. When I tried to go, the rear wheels started spinning. I then switched on the low 4x4, and tried to go. The rear wheels continued to spin, but the front did not turn. I had new wheels installed, that has a cap that covers the manual locking hub, so I couldn't turn it to lock the hub. What should I look for to fix the problem?
2007 F250 4X4 Larriat SRW
As the title says are my front leaf springs bad? I got this truck 2 years ago and replaced all the ball joints, shocks, sway bar links,front hubs, rotors and brakes along with all the seals. I have a clunk in the front and I can't figure out what it's coming from. Could my leaf springs be clacking together? Truck
is a 2000 F250 SD v10.....
Driverside front
Rear spring
2003 F250 4x4 7.3L
While doing my brakes in the front, I tried to wiggle the front left, nothing. Solid. Then when I did the right, I was surprised to see it wiggle when I grabbed the tire. So I looked to see what was moving.
Not the U joint, not the ball joints, But it looks like what is a drive shaft.. (I am new to this stuff). On the right side a shaft comes out of the axle just before the U joint and the rest of the wheel assy. What is wrong?
I have a 2008 F250 XLT. When i am driving and turn the wheel a squeak is noticeable while the tire is spinning. as i speed up the squeak gets faster and slower when i slow down. I have it narrowed down to the right front tire but cant figure out what is causing it.
View 5 Replies1999 F250 super duty. I am having a problem with the front right turn signal not working. The indicator on the dash also does not work but I can hear the relay clicking double time and the rear signal works. I have changed the bulb and fuses and went under the dash and the column to be sure a connection had not come loose. I have looked through the forums to try and find an answer with no luck. What to try next?
View 4 Replies2002 F250 4 wheel drive manual hubs, 7.3....
My first thought was to have the tires rebalanced and rotated to see if it is tire noise? I am hearing damage on top of the noise from the 7.3, hard to be sure!
So I have to replace the front unit bearings on my 2004 f250 4wd. My question is, which thread pattern I have, fine or coarse? I have read that the early models, 99-02 have coarse threads. Afterwards they are fine. I am going to order online as they are cheaper than the local parts store. I have the Timken part numbers for either thread pattern.
View 4 RepliesI have a 2008 F250 5.4 4x4 supercab long box (68,000 miles) that has a little bit of movement in the front wheel bearing and hub assemblies. Made it through inspection OK but it will need to be changed soon. Just asking for everyone's thoughts on brands they prefer. I have had great luck with Moog brand products in the past. I put SKF hubs on my wife's 2010 Explorer and they I would say are top quality also. Not interested in a conversion kit or cheap junk. I want a good quality unit. What brand has everyone had good results with? Are Moog or SKF the way to go?
View 8 RepliesWell, I've been meaning to get to servicing/re-greasing the front hubs/bearings for a while but somehow it keeps getting moved down the list.
2000 F250SD 4X4 Gas Manual Hubs+Trans
I'm currently going through the many threads that turned up in my search query.
Driving slow with the windows down it seems like a low whine or squeal coming from the left front. Tone changes when working the steering wheel left and right. Haven't detected any grinding sounds. Any other techniques for isolating the problem? It's going up on jack stands tonight and I'm going to see if there is any wobble from the front wheels and I'll listen as I turn each of the front wheels. Oddly, the right front hub is hard to turn. Left front turns easy.
Viewed Rob259956's videos on servicing the hubs. Currently researching accessing the wheel bearings. It seems pretty straightforward. Truck has been off road but not mud bogged or anything like that. I'm guessing a bad bearing will be easy to identify as will a bad o-ring but any other stuff I should look closely at?
I have a 2008 f-250 6.4 Diesel. Yesterday the Brake Fluid light came on. I thought maybe a sensor, but once I parked and checked I realized my brake fluid was down to the Min line. I started looking for a leak and it was apparent that it was the front drivers wheel area.
I am attaching a picture of the brake. The leak is either coming from the area where the fluid line runs into the gold thing (caliper?) or the bolt at the bottom of the gold thing.
Here's the deal. I have a 2001 F250 4x4 and I am getting a noise in the front drivers side wheel. The noise is not a grind or clunk, but its like a u-joint is rubbing inside an empty cylinder kind of. Anyways, it seems like it does it only with small bumps. I took off my oem hubs and re-installed them and the noise went away for about a week. Now I replaced them with manual locking hubs and the noise is back. One other thing I notice is if i put the switch to 4x4 the noise goes away. I checked all major components for the steering and suspension and nothing was loose. The front end is tight. Is there anything inside the axle that would cause this? I dont know what to check for anymore. Where else to check?
View 4 RepliesI am needing to replace the front hub wheel bearing assemblies on my 03 F250 4x4. I know Ford changed the studs from coarse thread to fine thread in between the 02 and 03 model years. Mine has a build date of 08/02 and I haven't been able to find the exact date they switched over. I'm ordering the parts online and want to get it right the first time.
View 3 RepliesI have a 2000 f250 with auto/manual locking hubs and today the 4x4 quit working. The light comes on the dash and the drive shaft and u joints turn but the front wheels don't turn even when its locked in. I assume its the hubs? And when I am going down the highway about 75 the front starts making a hellacious noise but stops if I slow down is this connected?
View 11 RepliesI'm looking at a 2004 F250 XLT super cab 4x4 with a 5.4L with only 50k on the clock. It looks to be in great shape and drives good with only a few issues. Cruise doesn't work, it pulls to the left a little, and it has a slight roar coming from the left front wheel. Other than that it seems to be a nice truck. Its blue and grey two tone. Anything else I need to look at before pulling the handle on this one?
View 11 RepliesMy 99 F250 has just recently started making a "rattling" noise. The noise sounds like its coming from the front left wheel area. The noise is constant while driving down the road, its NOT created by bumps or anything, its a constant noise while moving.
View 3 Replies2004 F-250 FX4 SB 5.4 V8 140k
Issue: rattling/clicking noise from passenger front wheel area at speeds lower than 15MPH, made worse under light braking and/or turns to the right.
Clicking sound is speed dependant.
Spindle? Hub? Balljoint? Sway joint? Rotor Issue?
I need to replace the front passenger side wheel hub unit on my 2012 F250 4x4 120,000 mile reg cab truck. Its been a while but I did one on my 2000 F250 without any problems. There should be a few clips inside the hub that hold the looking hub and shaft together, right? Do I need any special tools for this job? What do the bolts need to be torqued to?
View 2 RepliesI got an 03 f250 with a 10 inch lift on 40x14.50 tires on 20x10 fuel hostage wheels. They rub my springs pretty bad when trying to make even the slightest kind of tight turn and the sound they make when they rub is even worse than them actually rubbing. My question is should i stay with this tire and wheel setup and try to get some 6061 billet aluminum 2 inch spacers? (I'm not sure about going that route though because of what i heard about spacers) or go down to some 38s with a 20x14 wheel that hopefully would push the tire away from the hub like spacers would do. I'm leaning more towards going to 38s because of the rubbing and also because I feel they might look better on the 10 inch lift rather than the 40s but dont know whats the best thing to do.
View 12 Replies