Ford Super Duty (1999-2016) :: 2006 - Power Steering Grinding Noise?
May 4, 2014
i have a 2006 F250 XLT 5.4L 4x4 Crew Cab. after months of dealing with an ongoing power steering issue and replacing pumps left and right, i decided to replace the entire power steering system. Ordered Gearbox, Pump and Cooler from dealership. The install went fairly easy, and finished in 2 days.
The truck used to whine and grind as i would turn wheel any direction, driving or in park and the wheel used to pull , like jerk a bit when i would go like in a u-turn.
Not anymore, all those issues are gone. Steers straight , no whining , wheel doesn't pull anymore and all seems fine, EXCEPT when i take a turn , for example onto a driveway where its a bit of an incline. Then, i hear some grinding noise and a bit of vibration in my wheel. I think it comes from gearbox or pump.
Im scared not to drive it too much as all is new components and don't want to ruin all over again.
View 6 Replies
Advertisement
Truck seems to run ok, but when I push the brake pedal down a bit, a strange grinding/howling noise comes from the engine bay and same thing with the power steering. When I put the brake pedal down to the floor, it stops?
View 12 Replies
I noticed the front diff of my truck was whining, so it decided to take a look. I noticed that the passenger side hub would not unlock when it was in the lock position. My truck has the manual floor shifted 4x4 and the manual hubs, not the ESOF. I removed the locking hub from the hub bearing assy and I noticed that the axle shaft still moved when i spun the wheel. I know the manual locking hub is trashed (pieces fell out when i removed it from the truck) but does the fact that the axle shaft still spins in the assy with no hub installed also mean that my hub bearing assembly is trashed and warrants replacement?
Finally, the number one most annoying thing with this "new to me" truck, is this noise in the steering column. It is very hard to describe, but when slowly turning the wheel, either left or right, it will produce a groaning/grinding sound that CAN be felt in the steering wheel. There is a roughness/vibrating/binding type feeling in the wheel when this noise is made. I lubricated the boot that goes through the firewall, and the spring around the shaft behind the turn signal switch with silicone spray and the noise goes on. It really feels like it is somewhere in the column, but as I said before I do not know anything about these superdutys. I work for chrysler and I have never experienced anything like this on a dodge truck.
Its not the best but here is a video, little grinding noise that I am speaking of is most noticeable when camera angle changes to the side of the column, just before door buzzer makes noise : Grind steering - YouTube .....
View 7 Replies
My 2006 F350 is giving me grey hairs. I'm trying to figure out what's going on with it. I have been getting an occasional (more often than not) grinding noise from what seems to be the front of my truck. It will do it from a stop, under light, moderate, or heavy acceleration. Doesn't matter. If I let off the throttle momentarily it will stop until it shifts and will grind again through all shift points it seems.
Logic says it's got to be the wheel bearings or locking hubs. I recently did both on both sides to no relief. Because this is an 06 it had a different hub set up then the previous years which I've read a lot of info about (needle bearings). It doesn't make a lick of difference if hubs are locked or on auto. If in 4x4 (ESOF) or 2wd.
As mentioned I replaced both wheel bearings with FORD parts and both locking hubs From FORD as well. (Small fortune). Axle u joints seemed tight. Greased me up but no play.
View 6 Replies
I have an '06 F-250 that's making a quiet grinding/humming noise from what sounds like the front end. It doesn't seem to be coming from any side in particular, just an omnipresent noise whenever the truck is moving. It's constant with speed, and most noticable between 30-60 KPH.
Truck has about 268,000 KM on it right now, and has been worked pretty hard for whatever that's worth as well.
View 3 Replies
What is the best way to bleed air from the power steering lines? I just replaced the power steering pump on a 06 6.0 f250 and now I need to bleed the lines and refill the power steering. I'm just curious as to what is the best and easiest way to do this.
View 14 Replies
I'm working on an 05 with a 5.4. I got it with a bad valvetrain noise on the PS, which ended up being a bad cam, and one bad rocker. I changed the bad rocker and any others that showed any wear, the cam, and all 12 lifters on that head.
The truck starts, idles, runs, and drives fine; identical to my own 05. But if I get on it, it has a dead spot around 3-4k rpm, then picks right up again. After a while, I get the p0012 (Variable camshaft timing over-retarded bank 1). After I get it pissed off, the idle gets rough as well and bogs down.
Now I know the cam went it correctly. I used the wedge tool so the phaser never left the timing chain. I marked the chain as well just to be safe, and the phaser only goes on the cam in one position. Also, it idles too nicely, and runs fine under normal acceleration.
Tonight I swapped the VCT solenoids from one side to the other. It took a lot longer to get the code, but finally came up as a freeze frame dtc, and on Bank 1 again, so it's not the solenoid.
So in my mind, all I can think is that the timing chain jumped (which I don't think is likely due to the good running under normal conditions), or the phaser is bad/sticking on Bank 1. I popped off the oil fill tube and the phaser looks fine physically, so I don't think I banged into it somewhere along the line. I also manually excited the Bank 1 solenoid by grounding the purple wire, and it gives my the same rough idle which I get after the p0012.
It looks like the phaser to me. Another mistake I made was not scanning the truck when I first got it. It came right from a repair shop which diagnosed the camshaft, but I would have at least known if they cleared any codes from it.
View 13 Replies
I recently had a close encounter with some large rocks on a bad road and broke the power steering cooler. I lost some fluid and pressure as I had no brakes and it steered like a log truck. Replaced the damaged part and added fluid. I was informed by ford technician that air in the lines would make noise but would eventually work itself out. Well the brakes work and steering is getting better but it is noisy with steering and brakes. How long should it take to get the air out? PS the fluid looks foamy now. I should also mention it was making a slight humming noise before the incident with the rock.
View 9 Replies
I have an 06 F-250 5.4 gas w/138k. It had recently had a lot of play on the wheel (15 degrees maybe) and last week I made the move to replace the gearbox with a redhead box. All seemed to go ok, but now the steering is stiff and it won't come all the way back to center after a turn. It turns smoothly and completely with no binding, but it has to be moved the last 1/3 turn back to center.
I flushed the fluid initially with Valvoline max life fully syn. Then second guessed myself after the problem started happening so I switched it back to regular Mercon. No improvement.
I had it on stands today and it was extremely difficult for me to turn my tires left to right manually (at the wheel). The only other thing I did was adjust the sleeve on the drag link to straighten out the steering wheel.
Should I be able to turn the tires left and right from the wheel easily? Every now and then I hear a whine from the pump which I never had before, but 99% of the time it seems fine and is quiet. it just feels like something is over tight but everything should be to spec.
View 3 Replies
1999 f250 super Duty V10... I am having some problems with switching out of four wheel drive. S, when I flip the switch back to 2 wheel drive everything, seems ok at first, but within a mile or two I will hear this grinding coming from the front that sounds like the gears aren't completely disengaging. The inky thing that prevents this grinding from happening is switching back into fire wheel drive and keeping it there. What might be causing it to not stay disengaged ?
View 1 Replies
Well, I've seen a lot of posts for this but all seem to be geared to 4WD trucks.
I have an 04 250 KR 2WD. I get a sensation of popping/clunking in the LF area when I stop and start like the front axle is moving. Also, at about 50MPH, I get an oscillating hum/vibration in the same area. I've already checked everything and it's all tight, as far as I can tell.
When having the fuel filters changed, I noticed the truck "drooping" on the right side. Coincidence? I have already replaced and repacked the bearing on the LF wheel.
View 1 Replies
My 1999 Ford F350 Dually 4x4 started making a grinding noise every once in a while about 3 weeks ago. Now it is doing it quite often, randomly as I am driving. I do notice the noise stops when I stop the truck, or when I flip the switch to 4x4 and back while driving.
View 1 Replies
Went on a 400 mile trip today and noticed some strange noises. The rig is an 06 F250 lariat, V10, Zf6, SC, LB and only has 43k miles. It behaves normally except when coasting down a hill at 65+ mph, and it doesn't matter if I'm in neutral or overdrive, it makes a feint grinding sound that gets louder as speed increases. Maybe grinding isn't the best word to describe it, I'd say a cross between humming and light grinding. As soon as I give it any throttle or put any load on the tranny is goes away. It's really freaking me out as I just got the truck a month ago and I know the ZF6's are almost bulletproof.
View 14 Replies
For starters I have a 1999 F-250 5.4l changed all 4 ball joints about 15,000 miles ago. I have been hearing a grinding noise coming from the front end for the last month only when I turn left and at slow speeds. I was servicing the TC so I threw it in 4 wheel to check it and it wouldn't engage until I started moving. When it did engage it was a bad grinding/ clunking sound coming from maybe the differential.
View 14 Replies
I have a 2001 F350 with a7.3 power stroke, 6 speed manual with manual t case and hubs. I have a bad grinding noise when in 2 wheel drive. Similar sound as if you are trying to shift t case into 4 wheel drive too slowly. The grinding is constant in 2 wheel drive, but if I shift it into 4 wheel drive, the noise completely goes away. I have been driving around in 4 wheel drive (T case only, manual hubs not locked) for the past 2 days. If I shift back into 2 wheel drive, a constant terrible grinding noise returns. What could be wrong, and why it goes away in 4 wheel drive?????
View 3 Replies
Noticed this morning that the truck appears to have a screeching/grinding noise while going straight down the road. If I go a bit of speed and stop the engine and exhaust from revving and making noise and just let it roll I can hear it and hear it better by sticking my head out my window. My engine and 5" straight pipe hide it well while im going though. I think its coming from my front driver side but im not 100% exactly sure. What it could be? I know there are a lot of variables to cover but any ways to check things out? Also! I can hear it slightly while reversing slowly.
View 8 Replies
My dually has started to make a rubbing or grinding noise just about every time I make a turn, left or right. What this could be, truck has 8500 miles on it.
SD Dually
View 9 Replies
I have a 2016 Superduty. I was sitting still in the drive, engine running and Tx in Park. Following the manual's instructions, I put the Tx in Neutral, turned the 4x4 to 4x4 high and then to 4x4 low. I then pulled the to engage the electric locking rear diff. I put the Tx in Reverse with the foot still on the brake and then as I gradually lifted pressure off the brake pedal (I think) and started creeping, I heard a medium pitched grinding; not so much like spur, helical, or hypoid teeth grinding; more like cog gears. I stopped the truck and disengaged everything. Later in the day while on dirt I put her through her paces proper and all was fine. I guess I'd like to just know, given that this is my first 4x4 with so much electric shifting, what actually happened. If you are pretty sure of what I heard but are puzzled by the sequence, I could have the order of things a bit off as my brain was just about wiped completely free of all memory when I heard that sound so I may have the order of what I actually did, wrong.
View 4 Replies
My 2012 f250 6.7 has what sounds like a chain spinning when idling when you give it fuel it quiets down.
View 1 Replies
My 03 F250 7.3 is making a grinding noise when I let my foot off the accelerator and coast in 4x4, I replaced the hubs with new warn premium hubs and it is still making the noise. The noise does not occur when I take it out of 4x4.
View 2 Replies
I recently noticed my truck (2006 f250 v8) making some clicking noises on really sharp turns and also horrible grinding when stopping (like the brake pads were shot).
I replaced the pads a couple years ago, so I didn't then they were bad, but I took a look tonight. What I found was a couple of seals blown on both sides!
What these are and how this might have happened? They look the same on both sides. How do I replace them?
View 14 Replies
