Ford Super Duty (1999-2016) :: 2006 F350 Not Starting - Code P2285 - Injector Control Pressure Sensor Circuit Low
Jun 26, 2015
I have a 2006 f-350 6.0 and i went to fill up my truck with diesel. After that the truck did not start. Currently has the code p2285 - injector control pressure sensor circuit low. I tried disconnecting sensor, still no start.
I have the torque pro app and another 6.0 that I use for comparison. Check power at ficm 48 volt, flp 11.5v, FVP 11.5v. Hpop while cranking shows 1400 psi. removed oil filter and see low pressure oil ok, fills up reservoir. ipr at crank about 65%. fuel filter full of fuel.
Replaced the dummy plug on passenger side because originally hpop was very low psi 12. after replacement it went up to 1400 on cranking. What should I be looking at next, should I be removing ipr? should i be looking at crank sensor or cam sensor? Just installed 2 new batteries also because my dad kept cranking the truck until it died.
Checked to make sure fuel cut off relay not triggered, Ok. The truck has been having long cranks before it died. Also right now the injector cycling is 10 seconds long while on my other 6.0 it is about 4.
View 14 Replies
Advertisement
Engine light came on yesterday and started missing on take offs. Giving code p2285 Injector Control Pressure Sensor Circuit Low. I've done the research and understand the problem. It's the weekend and shops closed until Monday. Is it safe to drive in the mean time? Is there any risk of doing damage? What's the risk of it quitting or failing start in the short term, today?
View 2 Replies
Traveling cross country & got a check engine light telling me "injector control pressure low". Replaced ICP sensor and injector pressure control regulator. Removed old one and installed the new one.
While looking for one of the nuts that attach the glow plug relay in the valley I found a small round part looks like maybe a valve seat. About 1/2" round with maybe a 1/4" four flute spline in the center. Has an o-ring on one end.
Is this something that followed the old ICPR out and fell off the end when It cleared the mounting hole? It looks like the ICPR would bear against this little thing.
View 2 Replies
I have been trying to find a new sensor after my truck popped a P2285 code. I can't find ICP sensor at any auto parts store. I found this but it was labeled as a fuel pressure sensor on RockAuto: More Information for Standard Motor Products ICP103... Is this the same thing?
View 2 Replies
I bought my truck 2 month ago. I use it for commuting, only short trips now ( 10 min ). After about 2 weeks the Check Engine light came on. The truck is running fine, no problems I believe, starts easy. After another 2 weeks, the CEL disappeared. Another week, and the CEL came back on and it`s there since. I have a code reader, these are the codes and meanings according the manual:
P0299 - Turbocharger "A" underboost condition
P2286 - Injector control pressure sensor circuit high
P2287 - Injector control pressure sensor circuit intermittent
P0299 Pending - same as first but with "pending" status
This is my first diesel and my first turbo charged engine. Is this a common problem? How serious? It`s a bit strange that the error came up before but disappeared. Can that happen just because of the short trips I`m making? I`m planning a long trip soon with towing my trailer, so I want to make sure the truck will not break down during the ride.
View 14 Replies
I have a 2006 F-350. I got a code p2623 ipr circuit open. I ordered a new one and currently waiting on it. I pulled the old one and the screen has been replaced already. How often do these valves go bad? Is there anything else I should check?
View 6 Replies
2011 6.7... My truck is throwing code P2033 Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor. What is the part number for that sensor?
View 6 Replies
I recently picked up a 2005 f250 SD 5.4 4x4... I was having issues with sporadic shifting and wandering shifts while cruising around 100kph, scanned it and came up with p0721 OSS sensor circuit performance fault.
I checked the harness and all looks fine, now I attempted to remove the OSS at the rear of the tranny, got the 8mm bolt out however could not, for the life of me get the sensor out. I tried not to use pliers to twist the sensor or anything for fear of breaking the sensor off and having bits go into the transmission.
View 2 Replies
2006 6.0 superduty showing low circuit codes on all 8 cylinders so i checked the FICM and it has 48v when key is on and while turning engine over. What to check next?
View 11 Replies
My scanner reads P0001 Fuel Volume Regulator Control Circuit Open. My truck shuts down without warning, runs great otherwise. I've changed 2 grey CPS units and now have the Black IH one installed. What the Fuel Volume Reg.is? Is it the IPR on the HPOP?F250SD 7.3 225,000 miles.
View 10 Replies
We just bought and '05 F350 Turbo Diesel, about two days after getting it the check engine light came on. We had the dealer check it since the mechanic wasn't in and it came up as "Fuel Level Sensor" . My husband can't remember the exact code. We have been told it's no big deal but we want it fixed and the engine light to go off. The dealer is giving us the runaround, or at least I think so.
View 14 Replies
I keep getting a lean bank code. I have cleaned tb and replaced one of the rubber lines. It only comes on when I take a good ride with the truck. Not sure what else it could be. I'm thinking O2 sensor maybe.
2008 F-350 5.4 3V. 65k miles
View 9 Replies
So I scored a real deal on a set of Michelin on same size 17" OEM wheels that were taken off a brand new 2017 F-250 at about 100 miles. I installed them on my F-350 and had no faults show up. The tires had been marked as to which corner they had come off of so I put them on the same corners of my truck.
After driving about 50 miles I got a "Tire Pressure Monitor Fault" code. I pulled out my owner's manual and followed the relearning procedure exactly but I get the two beeps and the fail retry message from the left front. I have tried three times and get the same result.
Looking for info if the 2017 F-250 sensors are compatible with the 2011 F-350? Have I overlooked something? I habitually manually check my tires anyway, is there a way to disable the TPMS? Is it time for the dreaded trip to the dealer?
View 14 Replies
2005 F350 crew cab with 6.0 currently cranks but no start with a P2291 error code. Using scanguage 2 it shows icp 0, IPR 67.7, FICM 47.5 while cranking. Disconnected ICP and still no start. removed icp and hooked up air and I do not hear/see any signs of air leaking. When I disconnect the air it then whooshes out. About 2 months ago got a #1 cylinder contribution error code and changed out that injector and it has ran fine up until this issue.
Can this be a IPR? I am leading towards the HPOP, but as it costs a pretty penny would really love to make sure I tried every other avenue.
I have 197K on it, and 2 years ago did a EGR cooler delete. In May this year replaced the oil cooler, and then in August changed out the #1 fuel injector.
Oil cooler screen was broken. Cleaned the entire reservoir out. Could this just be a clogged IPR? or seeing the change while cranking an indication that it is working?
View 1 Replies
Have a 06 f350 just rebuilt the engine. Started up ran it down the road a couple miles and lost low side oil pressure. Got back to the house and will not start again so put a gauge on and it only has 3 lbs after cranking for 10-15 sec. Pulled the balancer and lpop cover and front cover had some deeper scoring then before. No noticeable stuff in the pan or filter. Changed out the front cover and lpop. Still has only about 5 psi.
View 3 Replies
I have an '06 F350 dually with a 6.0 diesel. I bought this used about 5 years ago and for the most part have loved it. i would always smile on the inside when i heard people bash the 6.0...i thought i got lucky....until today.
140k miles. recent oil change. all is swell...until this morning. Stick in key and turn it. glow plug indicator comes on...all lights come on for a few second....wrench, abs, dtc etc....wrench shuts off...glow plug light comes on...4 or 5 seconds later wrench light comes back on....turn key and NO CRANK.
All fuses are fine...starter cranks if i jump the solenoid...but it won't start. Miles to empty and everything else is just dashes hit the OBD and it says "engine sensor data error"/ "trans temp error" ...
View 1 Replies
2001 f350 7.3 Changed front injector drivers side inspected all 4 glow plugs on this side turned motor over my hand 5 time reinstalled plugs put back together hooked both plugs back up started truck and no of the cylinder on drivers side are firing checked them with temp gun!! what did i not do or do wrong.
View 4 Replies
2007 F350 6.0 .. I let the truck sit for about a week went out to start it truck cranked right up then died now the truck wont start truck was running fine until this I wasn't having any starting problems. the codes are all eight injectors low circuit tested ficm had 48.3 volts...
View 1 Replies
I've owned my 2012 F-250, 6.7L for less than a week and it has a check engine light. The local dealer can't see me for a week, and I need to leave town next week.
I went to AutoZone to have the codes checked and this is what they came back with:
P2033
Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor 2
P2031
Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor 2
Can I drive on these codes, or should I park the truck until Ford can see me?
View 2 Replies
2001 F250. I have had issues on other trucks where you get a funny-acting speedometer with a code that comes up as VSS (sensor on top of the rear differential)....And it shifted exact same way.
My new truck speedometer is totally fine and the ABS is on with codes:
C1158 Left front speed sensor coherency malfunction
C1155 Left front speed sensor input circuit malfunction
Shifts about the same way on the trucks with bad VSS.
Question is will a bad front speed sensor affect the way the trans shifts? Doesn't happen all the time. If you go slow it shifts smooth. If you pull off fast a barely noticeable jerk from 1-2 and 2-3....
View 3 Replies
This is my first Ford. 2008 6.4L 165K miles full delete. Bought this truck at auction already deleted. Found an H&S pod mount instructions in glove box and so I am thinking it had their software loaded to it. I knew it had sat a while, but did fire up no problems. I have already replaced all fuel filters (actually learned I did them backwards, and did not cycle the key) and had no issues re-starting! I've put at minimum 30 minutes but no more than 1 hour run time on this thing post filter change. I'll get to the gritty. . This all started when I pulled a P0201 code for Injector Cylinder 1.
I pulled the valve cover to troubleshoot the injector, following a post I saw few days back. All checked out fine with the #1 compared with #3, and so I cracked loose the fuel line going to the #1 injector. The line was dry and thought it was strange, but I had changed out the FRP sensor prior and remember no fuel came out then either. Before pulling into the garage the truck was running rough but thought this was due to a P0193 code FRP pressure Circuit High (again). So I put the line back on, tightened the darn out of it.
I know these things see a 26K psi at times. I depressed the Schrader valve at the fuel cooler and got only a minute bit of air out. I didn't think this was enough, and so I took the Schrader valve out, hard lesson learned. I re-installed it and I fashioned a homemade tool connected the Schrader valve with a ball valve to cycle the key-on and purge out the air. I have ran the batteries down cranking trying to get it to fire. I am now getting no more air bubbles.
Had to get another diesel pickup to keep juice on the batteries. After 3 hours, 6 hours total, cannot get this thing to fire off! Am I missing something simple? Everything I have done to this point before reading the forum I have done backwards and all has been fine! Could it be that just now I am seeing the effect of the filter change being done backwards? On my scanner I can see the live FRP, it has to be the cmd, it is sitting at 29Kpsi. At this point should I re-pull the filters and start fresh?
View 1 Replies
