Ford Super Duty (1999-2016) :: 2006 F250 Truck Shut Down Wouldn't Start Back
Oct 16, 2014
Ok truck shut down wouldn't start back. Put fuel filter o. Frame cranks but won't start. Was told has high pressure oil leak in engine?
View 8 RepliesOk truck shut down wouldn't start back. Put fuel filter o. Frame cranks but won't start. Was told has high pressure oil leak in engine?
View 8 RepliesI have a super duty with the 5.4 in it. it just quit while off road n wouldn't start back up. pulled it back to camp, wiggled wires around cam n crank sensors n it fired up n stalled numerous times then just wouldn't even fire back up. loaded on trailer n brought home, buddy put his tester on there n said there was no rpm reading so I replaced the crank sensor, it fired up n stalls still. wires seem to be good to crank n cam sensors. don't have a manual to tell me what relays are what.
View 11 RepliesSo I'll be driving down the road and the gauges will randomly start jumping around then the truck will just shut off, this just started a couple days ago, it seems to be gaining in frequency, when i try and restart the engine all my warning lights flash on and nothing happens, try again and it starts back up, now the last time it happened all of the above happened but it was followed by a fast clicking noise from under the steering column, it has to be a electrical issue as i have full tanks and motor is in tip top shape. Also no codes pop up with my code reader.
View 1 RepliesI have had this issue with the truck 2008 F-250 6.4L since I bought it a year ago. At first it seemed as if the truck wouldn't start whenever the water temp gauge was working while she was hot. When the gauge wasn't working she would start right up like a champ. Well a year later ( have only been driving it for 6 months) a full engine rebuild, new high pressure fuel pump ( injector pump on top the engine below the turbos) she still won't start when she is hot. What the issues are.
Right after the engine rebuild I was getting the p088 code which is for the hpfp but since I cleared the codes right after the engine was rebuilt I haven't gotten the code again. I replaced the high pressure fuel pump this last weekend hoping that it would solve all of my issues and she would be like brand new again, but it didn't do anything. When I ran codes right after I installed the high pressure fuel pump I got a few codes p0684 which is the glow plug control module p0284 ( google said) gear lever y position correct but I'm unsure if that's right.
P0528 which is the fan speed sensor circuit ( that was unplugged during the removal of the hpfp and power steering pump or the radiator) p0480 cooking fan circuit ( also unplugged ) p174e out put shaft wheel speed correlation ( not concerned about that one) p008c fuel pump control circuit p008d fuel cooler system ( taken out and unplugged using installation of new hpfp) p115a ( low fuel level forced limit power) that is from trying to start while she had a little bit of air in the system after replacement) p2291 injector control pressure to low- excessive cranking ( probably from the air in the fuel system again). I cleared all those codes once I got her up and running again. Checked for codes yesterday and the only one that came up again was the p0684. Where to check next for this hot start issues,and don't know what to do at this point.
2001 F250 5.4 ... I'm losing my mind chasing a Gremlin. I've been having mostly intermittent starting issues with my truck. I've had the truck for a little over a year, after someone totaled my previous one.
It occasionally wouldn't start on the first attempt, but it got really bad in the last couple weeks.
I first thought it was a faulty inertia switch or wiring in that vicinity, as at one point after manually tripping and resetting the cutoff switch it would start, UNTIL I put the trim panel back. At this point I think that may have been a coincidence.
I eventually probed the switch and it tests as it should electrically.
I put in a new fuel filter and things were fine for several days, but it acted up again. That time was last Saturday. Got it to start and all was good until tonight. Now it won't go, and I've tried so many times that I can see the battery power is dropping.
Last Saturday I pulled the relays from behind the radio and cleaned 'em up real nice. Also, just to check another variable I swapped the two that matched.
I'm about ready to change the fuel pump, but I've heard so many people say they did that but the problem was something else. Not only will it costs hundreds of dollars, its cold out and we'll have to drop the tank in the driveway.
In addition to the relay, inertia switch and fuse, I have found some mention of faulty fuel pressure regulators causing issues. I'll pry the vacuum line off in the morning to see if I can detect fuel residue on the vacuum side. (There is some noticeable corrosion on the fuel rail in that area).
I REALLY want to make sure I rule everything else out before spending hours under the truck in freezing weather dropping the tank and changing the sending unit out.
On key-on there is a noise from the gas tank, but someone else listening described it as a click but no whirring.
I do hear the relay clicking behind the radio. (Also, I pulled them again tonight and put a meter to them. With 12V on the primary side, they click and the other side shows continuity on diode check, and about .2 Ohm on resistance mode.)
I went through a lot of trouble to get my spare out looking for the fuel control module before finding out my truck is about 3 years too old to have one too. What else to check?
I have a 2002 f250 SD v10 4x4. I had a ground wire break fixed that know noon of my instruments work. Dash lights up but nothing moves. Pulse my parking lights stay on when the truck is shut off or when I turn lights on then off. I have to disconnect the battery to get hem to shut off.
View 3 Replies2003 f250 crewcab 6.0 auto 4x4. I all of a sudden started feeling a vibration under the truck near the back when I accelerate and when I let off the gas no other time. No noises or clanking just vibration. I can wiggle the driveshaft inside the carrier bearing do you think that could be it or is it the rear end.
View 14 RepliesI bought this truck used and it is my first F-250. I took it to the shop last week and they found a few things and a cracked radiator was one. They replaced the radiator with a new one. I heard the sound before the new radiator and I still hear it now. The coolant level is not dropping and the engine is not over heating (also no fluid on the ground). Is this a normal cool down sound?
View 6 RepliesI have a 2006 F-250 Super Duty (6 liter diesel). The high beams stay on unless I pull the fuse (fuse 30). It doesn't matter what position the headlight switch is in. It is like the high beam flash on the multi-function switch is stuck. It feels fine, but high beams stay on regardless of position, even with the truck off. The low beams (if in low beam when the truck is shut off) do go out as do the running lights after 15 or so seconds (normal) it's just the high beams. Also the high beam indicator light is on all the time (until I pull the fuse) and the fog lights will not come on until I pull the fuse. Should I replace the multifunction switch or look elsewhere?
View 10 RepliesLast fall had one day for about three miles where wipers and washer wouldn't shut off. Now they won't stop at all. Thought the multi switch might be bad, removed whole switch and unhooked. Washer pump and wipers were still on and wouldn't shut off. Had to pull the fuse.
View 4 RepliesMy 2006 6.0 shut off immediatEly after starting this morning and never started back up. I have a scan Guage 2 hooked up. I'm showing no ficm voltage and no sync even when cranking. I physically checked the ficm voltage with a dvm at the screw to the far right on the ficm, and I have 48 volts. Why do I have 48 volts at the ficm, but 0 volts showing on my scan guage? And no sync when cranking?
View 4 RepliesI just bought a 2000 F250 SD, 4x4, 5.4, Quad Cab. I drove it off the lot, stopped to put air in the tires, jumped back in and it wouldn't crank. All of the dash lights worked fine. Tried jumping at the starter solenoid and got nothing. Got under the truck and jumped it off the starter, vroom, fired right up. Replaced the starter solenoid and had no issues for about 2 hours. Then it did it again. This time it wouldn't start at all. I towed it back to the dealer and they had it for 3 weeks.
Then yesterday I called and they said it was done. Picked it up, drove to the barber shop, got my hair cut, came back out and it did the same thing AGAIN. After jacking around with the shifter and turning the wheel back and forth 100 times it started. The key is kind of hard to turn sometimes in the ignition, so I'm thinking that the ignition cylinder needs to be lubed real good, but that shouldn't stop it from cranking the motor over, right? I was going to swap out the ignition switch, but I don't know if that will do any good either.
I have a 2008 f250 with 5.4v8. The truck starts intermittently. Put key in turn if no dash lights it doesn't even crank or hear a click. If u put key in and turn and dash lights up to starts and runs. U can watch the different lights (instrument cluster) light up independently like a xmas tree. When truck doesn't start if u disconnect battery when touching power wire to battery. Post truck lights will flick on/off if u tap cables to battery and leave on. Lights flicker on/off and then stay off. (Don't know why shouldn't flicker at all) after disconnecting and reconnecting battery truck will or will not start still depends on if dash lights come on before cranking.i replaced battery, starter, alternator, all the ground cable connections and wire cleaned. I haven't replaced the power side but are clean.
View 3 RepliesI have an 08 f250 with 6.4. when ever it rains the truck will not start. None of the gauges will work, door chime doesn't work and the only error light is the airbag light. Lights, radio, turn signals, horn all work. There is no clicking of the starter relay, the truck in dead. There is no water on the floor board nor is the floor moist. If I place a ceramic heater on the driver side floor board and blow hot air towards the firewall the truck will start in about 30 min to an hour depending on how long it sat in the rain. I've removed the air intake vents and there is no debris blocking the drains.
View 3 RepliesWhile driving up hill at 60mph the truck lost power. Rpm jumped up as to change gears as it hit 55mph. Still losing power until it shut off. I tried to restart and just got a click from the solenoid. No engine codes whatsoever. Battery had 12.1 volts but when turning the key to start in getting 8 volts. Had it towed home. Today I swapped batteries with my other truck and same click noise from solenoid. All lights, radio, ect still work. Where should I start? Alternator, fuses...?? 2008 f250 5.4 ...
View 12 RepliesI have a 2006 Ford F-250 coolant leak only when the truck is cold. Ive noticed it in the morning when I leaving for work. It looked liked it was coming from the passenger side yesterday and today it's on the drivers side when I'm sure is because my driveway has a small tilt to it I've looked everywhere I could under the hood and don't see it leaking.
I don't have any temp problems or white smoke and my coolant level has changed that much and for a few days the drip stopped now it's back. I tried to search for the answer but can't find it. I'm just wanted to make sure it's not the head gasket but I'm sure I would have a sign it it was. I will include where I saw it dripping from. It's parked on flat ground here ... That's where I saw a drip coming from driver side ....
My truck ran and drove then I changed my Steering Gearbox. After all that, I went to go start it, the trucked cranked and the batteries died. Hooked up the charger then and nothing, No start no crank. F250 2006 diesel 6.0 ...
View 14 RepliesI have a 2002 F250 7.3l with an aftermarket alarm. I can't read what the third letter is on the decal MV? 2000 Modular Vehicle Security. I added a pic of the alarm decal below. The key fob it had was aftermarket for the alarm and stopped working about a year ago. Today I unlocked the drivers door with the key and the lights started flashing and I can hear a clicking sound. It done this a few times back when the key fob still worked and I just kept hitting lock and unlock until it finally stopped. It won't let me start the truck at all and I have tried unhooking the batteries with no luck.
View 4 RepliesI have a 2010 F250 V10 4x4. about every 3-4 times when you start the truck....it seems as though the starter "sticks". If I catch it and shut it off and then turn the key right back it fires up and does not stick. Its as if the gear is staying kicked out into the flywheel. Are we thinking the starter itself? I'm thinking starter...but looking for input before I crawl under it.
View 1 RepliesI have a 2001 F-250 XLT 4x4 with V10. Truck will not start. No fuel pressure. My Haynes manual does not show ignition or fuel delivery wiring. I have found the relay box behind the radio/dash. I need a wiring diagram and info on which relay is the fuel pump relay. Want to know so I can jump relay to see if fuel pump is okay.
Truck had sat for a few weeks being ran very little, so had to jump start yesterday. Ran for about 15 min, the shut off, re-started and ran for 30 min. Truck sat for about 1.5 hours then would not start. Charged battery overnight and it is 100%.
Driving up a slight hill unloaded yesterday at about 40mph constant pedal pressure the truck shifts into neutral...at least that's what it feels like. Revs go up and no power. When I take my foot off the pedal the transmission catches and drives fine. There is no bucking or hard shifting, just that slipping. What it could be? This problem arose suddenly....never had any problems prior. It is not an issue that has gotten worse over time...
View 14 Replies