Ford Super Duty (1999-2016) :: 2006 F250 - Growling Noise That Is Speed Sensitive
Apr 26, 2013
I have an 06 f250 that is making a growling noise that is speed sensitive and sounds like it might be coming from the front. I thought it was tire noise from my old worn out tires but with new tires it still maks noise, but tires have pretty rough tread. How can I tell if it could be a wheel bearing? It seems like the noise quiets down a little on right turns. It is kind of a growling humming noise that changes with speed.
View 3 Replies
Advertisement
I bought a 2006 F250 6.0L a couple of months ago, from a dealership. It's been bulletproofed already, has an intake, coolant filter kit. Has 95k (mileage). Today, my fuel gauge dropped to empty from 3/4 of a tank for a couple of miles and set off the CE light. I hooked my scan tool to it, to clear the code (P0460).
After just checking other things out with the scan tool. I cleared it and went on... I had to run to the store, later on... I was pulling out of the neighborhood and the gas pedal was a lot more "touchy" and the truck, responded to it and it launched pretty good and blew a good amount of black smoke.
Do any of you think this has/or had a tuner on it and I may have activated it with my scanner?
View 6 Replies
I have a 2006 f250 and the heater will blow cold air unless you are driving in like highway conditions. If you stop or drive slow it blows cold air only. What is causing this???
View 3 Replies
I have a 04 F250 4x4. This growling noise has been driving me nuts. Its barely audible, but its there. Brought it to the dealer for service a few weeks ago, they said I had a bad front hub bearing. So I got the truck back, ordered a hub bearing, and last weekend jacked the truck up to see whats going on. Spun both front wheels, no noise whatsoever. Checked for up/down play and side/side play, nothing. So I held off on installing the hub bearing.
The noise is really more noticeable when going down the road and when you hit dips in the road. Kinda where the bounce puts more force/weight on the front end, the growling gets louder. The truck has 74k miles on it. Its there whether the hubs are locked or unlocked. Could I still have a bad hub bearing even though the wheel spins free and quiet, and no play???
View 8 Replies
I have a 2006 f250 lariat 192k no mods except k&n filter everything is stock. I have 2" pro comp level kit and a scan gauge 2 nothing fancy! Well the other day I noticed my truck was chirping like a Chirp chirp chirp...... Chirp chirp...... Chirp chirp chirp! It goes up and down with the rpm's but it's comes on and off only when the engine is up to running temps the belt does squeak during warm up but I don't think that's it, it's coming from the back of the engine I'm sure of it because I used a paper towel tube and listed right in the turbo hpop area on top of the engine but it's too hard to tell I can't find exactly where it's coming from, some people I've had listen think it's a belt or pulley or tensioner! But I'm not sure if it is because I've sprayed water, and wd40 on the belt and pulleys with no change!!! I'm afraid it's a lifter or something inside the engine yet it's too loud and pronounced to sound like it's coming from the inside! I'm just lost!
View 8 Replies
As I pulled in to park I slid only 3 or 4 inches and just kissed a snow bank, didn't even think anything of it. An hour later truck wouldn't start until I reset the inertia switch. Man that thing is sensitive!
View 13 Replies
While driving today, 2006 Ford F-250 5.4 L V8 138,000 miles , I experienced a problem. Started with the truck acting as if it was running rough, possibly missing. This was approx. 10 Minutes after starting. Checked the dash, no warning indicators and all gauges were normal. Approx. 4 more miles, the oil pressure alarm signals and I see the oil gauge has dropped to zero. I pull over, turn off and check the oil. Oil is clean and at a normal level. I restart the truck and the oil pressure goes back to normal.
Rev the truck up while sitting there and after a few seconds i hear a knocking noise in the engine and oil pressure drops again. Call the tow truck, driver used to be a mechanic . He asks me to start it again and the same thing happens. If you start it and let it idle oil pressure seems to go up to normal with no engine noise. Finally get to the mechanic and he calls me later saying the oil pump and screen may need to be replaced or the engine may need to be replaced.
View 3 Replies
I was running my 99 F250 SD with the V10 around the DFW area pulling a car hauler with a Jeep on it. The last 50 or so miles on the way home she started shuddering at a constant speed unless I turned off the overdrive or I was accelerating or slowing down.
She's never given me any issues but this is bothering me. 4x4...
View 10 Replies
I have a 1999 F250 super duty with a mean vibration at 70+ mph. It is a 5.4L manual trans manual 4x4 extended cab short box with around 250k miles on the body and 50k on the motor. It is a one piece drive shaft with the double knuckle at the t- case. it has had a vibration in the drive line since i bought i about a year ago. there is almost zero vibration at 60 mph but at around 70 the vibration starts to get really bad. The vibration is speed related because when i push in the clutch or pull it out of gear the vibration is still there. i seems to vibrate more when winding out in 3rd and 4th gear but that may just be because off the exhaust resonating or something. I have already done u-joints, balanced the drive shaft, put brand new tires on mounted and balanced, replace transfer case output bearing and both front hub assemblies. the vibration feels like it is coming from the trans or transfer case. every thing i tried made very little impact on the vibration. I'm a loss and i don't know what else to try. i know the throw out bearing an pilot bushing are bad and the clutch is well worn so ill be replacing that soon but i don't believe that is causing the vibration.
View 7 Replies
I have 2004 F250 6.0 diesel. I added 35s with diamo rims and I installed a front end lift which added a small leaf springs to the factory leaf spring to raise the front end 2 inches . The truck drives fine no problems at high speeds and low speeds except for right at 45 mph. At that speed the whole truck vibrates up and down . If I accelerate the vibration goes away. Discount tire rotated balanced etc and even replace a rim and nothing has changed. I did put the factory wheels and tires back on and the vibration went away. Put the big tires and rims back on and vibration is there at 45 mph. How to troubleshoot this ? I have 90,000 miles on her.
View 3 Replies
I have a 1999 f250 SuperDuty with a nasty vibration That begins at about 70mph. The truck is an extended cab 5.4l Manual trans 4X4 with a one piece driveshaft (No mid bearing). The Vibration appears to me to be a driveline vibration that is speed dependent. It is the same in gear, out of gear clutch in or out. I have replaced the wheel bearings/hub assemblies on all four corners, completely rebuilt and balanced the driveshaft the driveshaft, removed the front driveshaft, put brand new tires mounted and balanced on all four corners, new clutch, had the flywheel turned and balanced, and replaced the transfer case output bearings. Pinion bearing feels tight and does not leak.
Also the Input in the trans felt tight when i had the trans out. The truck had the vibration when i bought the truck and still vibrates after i have done all of this work. i did not change the motor mounts because they looked fine. when i bought the truck the tabs on the extension housing holding the trans-mount to the trans were broken so i make a huge "exhaust clamp" to straddle the trans and bolt to the trans mount.
After driving the truck up north last weekend the truck seems to shake going taking of at lower rpm as if the motor mounts and trans mounts are bad. I guess my questions is can a bad trans mount, motor mounts cause this Vibration at highway speed. if so is there a way to fasten the trans-mount to the extension housing without replacing the extension housing. If not what else can cause this issue?
View 7 Replies
Have a 2007 F250 6.0 diesel with the standard issues including misfire at highway speed. Assume the bulletproof kit also cures the stiction problem? in reviewing the threads and looking at the vendors, references are made to fixing the oil cooler issue, egr issue, etc., but no one addresses stiction issue directly.
View 10 Replies
I have a '16 F250 4wd with the 6.7 and approx 3k miles. There has been a strange sound coming from the front end when turning left from a stoplight. It sounds like something slides or shifts and it only happens once in a while. The noise isn't loud but you can feel it.
View 2 Replies
I have an 04 6.0 F250. I am having a shaking between 1500 and 2500 RPM around 45 - 55 MPH. I have no guesses what is calling this, but the truck runs fine otherwise.
View 8 Replies
Truck is an 02 F250 Automatic 4X4, 7.3 PSD.
Cruise control will turn on, will sometimes set speed and sometimes will not. If it does set and work it may kick off at any second or it may run fine. I have noticed it seems to kick off mainly after going over a slight bump in the highway or it may just kick off for the hell of it. Truck has 50,000 miles on it, I bought it new. Also having trouble with the throttle position sensor, it seems to have a "dead spot" at about 58 mph that shows up when I romp down on the pedal to pass on 2 lane roads. Can these two symptoms be related? Both are very aggravating. FWIW it does have the power adjust pedals. Truck is 100% stock, no power chips or other upgrades.
View 7 Replies
I have and 07 F250 and the #2 speed for the blower motor don't work (hasn't since I bought it) I read that the most common cause of this is the resistor under the hood on the firewall so I replaced that and still no 2nd speed??? Where I look next? Motor itself maybe?
View 11 Replies
Now that I use my truck as a daily driver I am noticing a vibration under acceleration at 30-35 and constant vibration at 45-50 accelerating or maintaining speed. I have replaced all three u-joints as well as new ribbed highway tires all around and still have the vibration. It seems worse in OD. I have done a little research and am either going to shim center support/machine a new one or have a one piece shaft made and need info on how to successfully gotten rid of this vibe on their truck mainly the amount of shimming required and the final driveline angle. It seems that most posts regarding this issue lean towards the fact that the 45-50mph vibe is normal for my year super duty and that's probably right but I want to remedy problem not "live with it!" (10 mile 45mph stretch to work @ 4AM, vibe bugs the heck out of me!)
Truck is 2000 f250 SC 2wd 4r100 3.73 gear currently 51000 miles.
View 11 Replies
2003 F250SD 5.4 4x4... When I recently heard a growling coming from my front end. I read some great posts on here about the whole front end tear down. Replaced all my ball joints, universals, wheel bearing hub units, locking hubs.....
So yesterday i came home from work, about 30 minutes later i hit the key on the truck and it wouldn't start. Kinda sounded like it wanted to but was starving for fuel. SO i grabbed the fuel pressure gauge and did a quick check......and No fuel pressure at all. Checked the fuse, Couldn't find a Relay in the fuse panel (Is there one for the fuel pump??). Anyway 4 hrs later the trucks starts right up like nothing is wrong.
Go figure, I'm 2 days away from my last payment ...now everything has to be going wrong.... Do these fuel pumps act up like that ??
View 6 Replies
I need to replace, its either a brake pressure sensor or speed control deactivation switch . Would like to know which it is and can I get a generic one from other auto parts beside a ford dealer Can post a pic of part as soon as I figure out how to do that exactly. 2002 f250 super duty....
View 8 Replies
My 2000 f250 4x4 V10 5spd manual with LSD and 63k mi gets an intermittent but very strong vibration like a shuddering, growling, rumbling in 2WD. The 1st time it only lasted about 1 second. It had been making a swooshing noise that sounded like front left wheel bearing for several thousand miles before this, so i replaced bearing assembly even though it turned smoothly.
After that, It still made the exact same swooshing noise and after a couple miles at 45mph, it had the strong vibration/shudder that lasted about 3 seconds. I stopped and locked the hubs manually. The vibration happened again in a couple miles, so seems like it's not the needle bearings in front stub shafts or locking hubs. On that last occurrence, the vibe went on for 5 seconds, felt the same with clutch in, and went away only after truck slowed down to nearly a stop. I've driven it about 6 mi total since the 1st occurrence.
Front right Wheel bearings feel smooth. I unbolted the driveshaft support bearing and it spins smoothly. The front u-joint maybe had a tiny bit of play, all bolts tight. I didn't check the nuts for yokes, but it didn't look like yokes had any play. Drive shaft slip joint moves smoothly. No up-down play at pinion shaft input into rear diff and output from transfer case. Rear diff oil was full with a little bit of silvery sludge on the magnetic filler plug, maybe 1/10 of a cc, no metals slivers or chunks. I raised the rear wheels and ran 5th gear 2WD at idle (~30mph) and touched a 4' listening stick to the drivetrain components.
The only odd sounds were from the rear differential. It sounded like a bad bearing with random crunches and thuds mixed in with the normal whirring. Crunches and thuds were loudest at front of diff housing. I blocked one wheel and repeated in 3rd gear. You could hear noise like gears meshing (noisy spider gears? maybe was LSD clutches?). The differential was warm after 5-10 minutes, with the hottest area being about 3" from the front of diff, just before the housing widens.
So, I'm guessing the pinion bearing is bad and the intermittent shudder is the bearing race spinning in the case when bearing seizes.
View 6 Replies
Today was the first time I have locked my wheel hubs in and used 4 wheel drive. However when I did all this i noticed that when I turn there is a growling sound but only when turning. It does not make the sound when unlocked and in 2 wheel drive.
View 4 Replies
