Ford Super Duty (1999-2016) :: 2006 F250 - Gauge Cluster Just Shows The Current Odometer Reading
Aug 2, 2016
I just bought a 06 F250 King Ranch and the information center on the gauge cluster just shows the current odometer reading. When I press the information button that is supposed to toggle between trip mileage and avg mpg just the odometer shows. This truck was vandalized (bought from auction) so I am wondering does it have a XL cluster so I am asking are all the clusters different between XL, XLT, Lariat, King Ranch, etc and I have the wrong one installed or maybe there is an issues with my information center.
View 3 Replies
Advertisement
2016 F250 Lariat, 4x4, Crew cab, Loaded, 6.2L gas, approx. 2,400 miles.
Well this was weird and spooky. I had to run to FedEx this morning. As I'm driving on the freeway at 70mph, suddenly the gauge cluster goes black, needles drop to zero, radio/panel display goes black, radio/AC reboots.
This happens about 5 times in rapid succession over the course of 35-50 seconds. Engine continued to run, could steer, etc.
Once things come back on, the radio was playing but the display showed it was off, same as the Climate but AC was still working.
I arrived at FedEx, shut off the engine, radio kept playing even after I locked and closed the door. Delivered the package, came out started the truck and everything worked fine for the next stop and drive home.
Could this be the same issue as was evident on previous models the the wire in the shift lever?
View 6 Replies
I have an issue with my 2008 f250 6.4 where the gauge cluster is dark and truck won't crank. The only light on the dash is the airbag light. I have tried reprogamming with my Spartan tuner, checked fuses, removed aftermarket alarm, charged batteries. I scanned and got two codes. P1260 theft detected and a u code no comm with cluster.
View 7 Replies
Got a weird one today. Everything was fine all day. Got the old girl smogged this afternoon and made one more quick stop. Got back on the freeway and up to speed and looked down. Speedo said I was 90? Yeah right. I was going with the flow.
So I plugged in my bluetooth ALDL dongle and fired up OBD Link. Well, OBD Link showed normal and accurate speeds. As did a second app on my phone for giving speed. So my VSS must be working correctly.
So my speedo is showing about 25 over actual. When the ignition if off the needle sits between 20 and 25. so did my speedo take a dump? Is there anything else I might try to see if it auto-calibrates?
View 9 Replies
So, recently acquired my grandpa's "old" 2000 F250 with the 5.4. I am a pretty mechanical guy, not a mechanic, but not dumb and change my own parts for a lot of stuff. Anyways, when I got the truck, I noticed it didn't like to get warm, or so the gauge said. It would go a little above cold, but you could tell, not a normal reading. I did a coolant flush because the system desperately needed it, changed the tstat, and a few days later, changed the Coolant Temperature sensor.
I pulled the old one out, it was covered in amazing crud from many years of being in there. Slapped the new one in, nothing. Doesn't register on the gauge at all, in fact the gauge acts like it is a dead gauge. I thought it might be the sensor, so I popped the hood again and found I had managed to break the plastic plug on the sensor. Figured that was probably the issue and went and got another. Same result. Checked the connection, it is in there snug. Didn't reset the PCM when I changed the sensor and some vehicles can be finnicky about that.
View 10 Replies
I got in my 06 f250 tonight and my digital read out on my temp control not working. My heater and A/C works but when I turn it off my outside temp is not on. Whats going on?
View 3 Replies
can i install a gauge cluster from a junk yard truck without reprogramming it? im not concerned with the odometer reading just need gauges. truck is a 2002 f250 sd 2wd auto gas.
View 5 Replies
I have a 2000 F350. I'm tired of my gauge cluster. No matter what, within a year one of the LEDs has a diode that starts to flicker and flash and makes my gauge cluster dance. I'd like to solder in a series of individual LEDs and do away with the expensive bulbs that always fail. The bulbs I soldered into my HVAC have never given me any issue, so I figured this would be a good fix for that and the awful hotspots.
I have torn down the gauge cluster partially before. when you pull the gauge faces off as a unit (including the various electrical components tied to the back of the gauges), there is a circuit board at the top of the cluster. It has two cables that plug into the main face part that pulls away from the white plastic chassis. Need to successfully unplug the cables in order to separate the gauge assembly from the chassis? I don't like the idea of soldering so close to it while having the chassis part propped up.
View 3 Replies
I keep getting this v0100 code in my tuner. Says lost communication with pcm/ecm? Bit truck doesnt die. Still runs but the rpms goes way higher before turbo kicks in?? What keeps causing this? Also my cluster gauge keeps shutting off and on so the cluster is going out. I will be replacing it. Do these two problems go hand in hand?
View 4 Replies
I recently (2 weeks ago) picked up my first Effie, a 2004 RN F250 Supercab XLT 5.4L 4x4 auto (dual Fuel Petrol/ LPG).
One of the things I am exploring is a problem with the tachometer reading high. I read on a thread somewhere on the forum that it was most likely that the earth of the tach plug was not connected. (It was a great thread but I can't seem to relocate it)
I am still chasing a workshop manual to get wiring diagrams, etc. In the mean time, where to locate the said plug/ earth connection?
View 7 Replies
Noise question. I have a 2011 super duty f250 xlt, and my question is I have a grinding noise that does not sound metallic and only shows up when its below freezing, only in drive and for about 50 yards.
View 6 Replies
I have a 2005 F 350 with a 6.0 Diesel! My heat quit on my wife and I the other night! I replaced some fuses and started the truck to make sure the heat was working and it was! So I thought while I am here I should replace some bulbs in the cluster that were out!
I took the cluster out, looked at the bulbs and they looked oK so I put them back in and put the dash back together! When I went to start the truck once I turned the switch on my gauges and lights started flickering on and off fast and all it will do is just click when I try to start it! I just had it running 15 minutes before this!
I went through all the fuses and if I take one of the relays out and turn the switch on all the lights and gauges seem to work right but when I try to start it, nothing! I replaced the relay and it starts flickering again! I had the relay checked at Napa and they said it was good! The relay was for the Powertrain module!
View 2 Replies
2004 F250 Crewcab 4x4 5.4 automatic.
My speedometer quit working - stays on 0, my odometer stays on 271006.5 miles. Everything lights up, when I do a gauge sweep, the speedometer goes from 0 to full blast then back to zero. On the gauge sweep, my odometer states off all the code stuff like I think it's suppose to.
Anyway, I was lucky enough to get a speeding ticket - driving with the flow of traffic, with the police officer behind me for a mile or more. Pulls me over, explain my speedo just went out, he said he can't let me off but the judge might. So I'm trying to fix prior to a court date.
Here is what I have tried so far.
1. Replaced the VSS in the axle - no change to problem.
2. Replaced the sensors on top of the tranny (2 of them) - no change in problem.
3. Sent the cluster off to a repair shop - they said it worked when it left there shop - no change in problem.
4. Replaced the battery - thought it might have a dead cell. - no change in problem.
5. Unhooked the battery, turned on the headlights, waited 30 minutes, put it back together. (did this probably 5 times) - no change in the problem.
6. Replaced the diff fluid. - no change in problem.
7. Replaced the front left abs sensor on the hub - the existing wire looked like it had rubbed on metal - possible short? - no change in problem.
So far I've just been what seems to be time and money at it with no luck.
View 12 Replies
I have no 4x4 lights on in cluster when turn the key in the on position and it doesn't engage when I turn my 4x4 selector. And I don't hear anything in the relays .
View 14 Replies
I have 2002 F250 4x4 with 5.4 V8. It has auto locking hubs. If I haven't used the 4wd lately I have to manually lock the hubs in, right side sticks, so I have to use pliers to lock into place. After a few times it works in auto fine. Anyway my issue. I went to use my 4wd so I manually locked the hubs, hopped in the truck and flipped it into 4wd. When I did the instrument cluster died. Radio, power windows and locks, turn signals all work. I just don't have any speedo, tach, fuel gauge, water temp, battery, no odometer. All went blank. I checked some of the fuses that I thought it could be from the owners manual but still no luck.
View 3 Replies
I pushed the Tow/Haul button on the gear shift and my instrument cluster went DEAD. Have checked the 3 fuses labeled instrument panel (F4,F35,F41) and they look OK.
2003 F250 6L diesel .....
View 11 Replies
2006 F-350 6.0. I have an intermittent problem with my Speedo reading zero while I'm doing 70mph on the fwy. since the speedo won't work the truck goes into limp mode, the turbo will not function at optimum level. I have replaced the diff. sensor, the trans sensor, the a.b.s.sensors, the instrument cluster to a reman cluster. Then when I had a local mechanic plug a laptop diagnostic program on it as he was running through the system inadvertently the radio cut out, so I found that who ever installed the after market stereo they cut a few wires to the harness, I went to the junk yard found the harness end and replaced the end. so with all that said and done no one knows what is causing this speedo not to work and limp mode. about 4 years ago the oil pump stopped working and ruined the turbo so the whole front end of that glorious 6.0 was rebuilt the problem started about a year after that.
View 3 Replies
My wifes truck is having some issues right now. Last week I was driving it down the highway, and the gauges all went off, the door buzzer was sounding, and the door locks where going up and down constant when I had my foot off the gas pedal. Found the fuse and fixed it with a replacement, but its down it three times all together since then?
View 9 Replies
I found one thread in FTE regarding replacing instrument cluster bulbs but the solution was to contact Circuit Board Medics. I have one dark area on the right side of the tach and another dark area on the left side of the speedo. Probably the same bulb that's out. Also, can attempt to replace the bulbs (assuming its a bulb and not a fiber optic of some sort) in the steering wheel volume and fan controls?
View 3 Replies
I was driving home the other day when all of a sudden all of my electronics in my truck turned off. Turned out when I got home my battery terminal was loose so it ended up shorting out. (fixed that) but when that happened my fuel was just under half way. The next day I filled up and was pulling a 3,000 pound trailer. My gas gauge didn't move at all, all weekend it was stuck at full until I actually went over a bump and it started moving down to a quarter. I knew here was no way I could go all weekend pulling a trailer and only lose a quarter of gas so I filled up again and was only be able to fill up 14 gallons.
View 4 Replies
1999 F250 V10 gas. I changed out the fuel pump, and now the gauge doesn't work. Checked all fuses - they're good. Is there any possibility that I could have accidentally pinned the float under the pickup sock, or got it hung somewhere? Is this a common occurrence? Don't really want to drop the tank again - but looks like I will have to in order to check/fix.....
View 3 Replies
