Ford Super Duty (1999-2016) :: 2006 F250 - Error Code P0470 / No Boost
Jun 25, 2014
2006 F-250 6.0... I'm getting a P0470 error code and no boost, The unison ring is free and clear, the Turbo will not create boost till about 2000 RPM on the road. If I unplug the VGT there is no change in the turbo.
When the vehicle is started there is no tone change in the exhaust. This just started after I replaced a dummy plug in the oil rail. I checked all the connectors as well. I cleaned the EBP and tube.
View 1 Replies
Advertisement
I have a 2006 f250 6.0 with 100000 started having low power when taking of from a stop. Then got a strong diesel smell and then the check engine light came on. I checked codes and got a p0470 and a p0299 pending. Where to start. I am new to diesels but I have a strong mechanical back ground.
View 4 Replies
Engine light and error code for tps occasionally comes on , then stays off a while. parts store said it was ok (shows full range) , but ford has an update for computer to fix. engine is v10 and parts store erased code and it hasnt come back. the only indication that something was wrong is the light coming on and once on the interstate at high speed , then the off ramp slow down, the engine seemed to want to stall as if engine not matching actual speed for a few seconds, then it was ok again. I was out of town and the mechanic that looked at it told me to go to Ford for an update. He tested the tps and said it was ok.
View 2 Replies
What this means, how can I fix it? No technical jargon or abbreviations that I will not understand. The error code is for a 2006 F-250 6.0L Diesel automatic. I have a tow controller installed it came with the truck when it was new.
View 7 Replies
CEL came on last night, OBD code PO420, truck is an 06 f250,5.4? Btw, truck running rough, no power on acceleration, in gear at idle, runs rough....
View 4 Replies
I have a 2006 f350 4x4 dually 6.0. The other morning when leaving for work I hard a loud air noise, like a jet. It only happens when the motor is trying to create boost. I have NO boost. No smoke. If I push the fuel pedal past 1/4, nothing. Its like its stuck and no more power at all. I have changed the boot from the turbo to the intercooler pipe. (looked like it had cracks in it).
Checked the cold pipe, no cracks seen. Check the exhaust clamps, into the turbo, they are tight. The turbo is seeping oil around the seal. I took the inlet, fresh air, pipe off. Check the turbo spool for looseness, fins, spun the wheel, ran the engine and watch to wheel. Seen no issues. Where to go now?? No coolant leaks, no oil leaks.
View 6 Replies
So I just bought a 2003 f250 v10 and I've plugged in my code reader and it couldn't get any info, so I took it to auto zone and they got an error code. I took a test lite to each little connection on the port with the ignition on and only got power to some of the metal connections on the port. So I'm wondering if all the little connections should have power? If so where should I start to look to find the problem?
View 5 Replies
99 F250 Super Duty 5.4 has a p7147 error. Traced all wiring cant find any short. Bought reman solenoid pack # are f81p-7g391-cb with green cover my old one in trans is f81p-7g391-ba with blue cover. Are these interchangeable? Have tried to read up on pwm & nonpwm and getting confused.
View 2 Replies
My truck is back in the shop for a third time for the same problem and the dealer is really clueless about anything. Here are the alarms I get when trying to start( Low Oil Pressure, Service AdvanceTrac, Engine Overtemp, Wrench Icon and Starting System Fault.)
When trying remote start nothing happens then the horns honks after a couple of minutes.
Below is the timeline and a video.
July 21, 2015 - Vehicle would not start, multiple alarms going off and dashboard has all icons showing. Towed vehicle in around 0700. Truck stayed in the shop overnight. Resolutions was told that the codes was reset and battery cable was tighten. I ask why the battery was loose when it was just in the shop for routine maintenance and it was signed off that it was good to go. I also told the service representative that I felt this didn't not solve my problem as it was just a quick fix.
Sept 4, 2015 - Problem is back, same symptoms, truck not starting, alarms going off, dashboard has all icons showing. Towed vehicle in around 1700. Vehicle stay in the shop for a week and was picked up around 1800 on Sept 11, 2015. Service representative stated they replaced the PCM and reprogrammed the keys.
Sept 12, 2015 - Yep you guess it, same problem and not even a full 24 hours from when the vehicle was towed to the dealership again. Truck wont start, same symptoms, alarms going off, all icons showing. Towed vehicle in around 0900. Vehicle would start now but check engine light is on. I have an inclination that all that will be done is to reset the codes.
2014 F250 6.7 Starting issues - YouTube
View 14 Replies
I just got my 2005 F250 diesel out of the shop. The errors codes P0299 and P2263 were listed on the computer. The service done, was to clean carbon from turobo charger and service the EGR valve. I talked with the mechanic and he recommended that I use Cetane Booster Additive. What would the Cetane Booster do? How would it prevent the carbon build-up in the turbocharger? What should I do to prevent turbocharger carbon build-up?
View 3 Replies
OD light flashes on my 2000 F450 7.3 but still runs and drives shifts fine. If i turn o/d off before i get going then it won't throw the code and start flashing at all. I am going to check the harness again to see if there are any bad wires. If not is it usually a bad solenoid pack i can just swap it out and fix the problem? I have to replace the pan soon so when I do if I need to replace the pack I'd like to do it then.
View 4 Replies
I've got an intermittent Trailer Wiring Error message that started appearing with a trailer connected on my '11 F250.
Brakes and lights work OK on the trailer, I thought I had read on the board here that there was a TSB for this, but I cannot find it.
View 10 Replies
2005 F350 crew cab with 6.0 currently cranks but no start with a P2291 error code. Using scanguage 2 it shows icp 0, IPR 67.7, FICM 47.5 while cranking. Disconnected ICP and still no start. removed icp and hooked up air and I do not hear/see any signs of air leaking. When I disconnect the air it then whooshes out. About 2 months ago got a #1 cylinder contribution error code and changed out that injector and it has ran fine up until this issue.
Can this be a IPR? I am leading towards the HPOP, but as it costs a pretty penny would really love to make sure I tried every other avenue.
I have 197K on it, and 2 years ago did a EGR cooler delete. In May this year replaced the oil cooler, and then in August changed out the #1 fuel injector.
Oil cooler screen was broken. Cleaned the entire reservoir out. Could this just be a clogged IPR? or seeing the change while cranking an indication that it is working?
View 1 Replies
Trying to perform master reset on sync because, from the title, phone button inoperative, No Aux In, and attempting to connect the ipod, you get "connection error see dealer".
The Owner's manual indicates Fuse 40 protects Sync, GPS and Sirius, so I figure that is the one. When you pull 40 you still have gps and Sirius, so I figure Sync must still have power also. So, what fuse powers the sync module?
View 1 Replies
I recently bought a 2008 F250 with the 6.4 diesel indirectly from a dealership. The truck itself has 220,000ish kilometers, but the engine (as well as the turbos) are Ford reman that had about 12,000km when I bought it and I have only put about 6500km on it. It is already leaking oil but that is for another thread.
The reverse sensors, steering wheel controls and part of the stock 6cd radio have never worked. The towing system has errors as well. The fuel level sensor often has problems reading the new level after I put in fuel, but that is always fixed by disconnecting the batteries and forcing a hard reset.
I figured the steering wheel/cruise control problem was due to either a broken clock spring and/or the brake pressure switch. I replaced both those as well as the airbag because the horn relay failed closed when I put it back in the wheel. It did not fix the problem. The steering wheel buttons still intermittently illuminate, but the radio controls and cruise control buttons do not function regardless. The truck isn't giving any codes either.
The towing system will activate lights and brakes on a trailer as well as set the gain, but it will not detect that it is actually hooked to a trailer. I cleaned the pins, but I haven't looked any further into it. No codes for this as well.
The reverse sensors/system does not work. It will lock itself in "off". I am guessing this is because one or more of the sensors have failed, but I am skeptical that it would be just that given the trucks other problems.
The radio does work, but the auxiliary input/mode will not work. I ran the diagnostics on the radio and on 'Test 1' I got "SELF FAIL B1342 ECU" and "B2477 CONFIG". I tried to clear the codes, but I can't. I think this means the radio is kill.
View 6 Replies
Ok says injector pressure sensor low first guess was the upgrade to the blue spring. Did that code clear for a day then comes back on looking at the hfcm but kinda unsure? Came on after we got the real cold snap and i had to buy a block heater I don't see one on here i also added diesel 911 to the tank this is a 05 f250 w 6.0l....
View 2 Replies
My 99 F250 with a V10 had an abs light come on and then it would go off. Now the ABS light stays on and it drove fine for a little while but the other night the Service Engine light came on along with the ABS light. Tranny was shifting harsh, winding out and I scanned the codes and got P0500. Is it the sensor on top of the rear differential or is it the ABS light causing the problem?
View 2 Replies
Where to find the PCM 4 digit code on 2001 F250 superduty/v10- Lariat?
View 3 Replies
I have a 99 f250 5.4l 2v with 165000. just two weeks ago i went to start up the truck on a job site to take lunch and it was running really rough. I talked with a mechanic at my shop and he said that it sounded like the aic or that i needed plugs. I went and bought aic and plugs and installed them all in one day. I unhooked the battery before i did any work and have changed the coil packs about 3-4 months ago when it was jerking at highway speeds. I am at a loss.
Read so much on the site about could be this or that and cant afford to through money at it like the govt does. I replaced the ait(air intake temp sensor) and the ect(engine coolant sensor) after i got a code from oreillys that said p0113 which is high input on it. I have read it can be so many things and it seems to be running rich because i am getting about half of mileage i was getting before problem started. i need a fix soon as i must drive the truck to work everyday which is a 52 mile trip total.
View 14 Replies
My 5.4 F250 with 200,000 miles having many problems... It all started a few months ago, when the cam needed to be replaced, and a cam phaser was also replaced at the same time. It ran fine after, then threw a code for cylinder 3 misfire. The guy I took it to said it was due to the huge crack in the exhaust manifold and that was messing with the o2 sensor coming up as a cylinder 3 misfire. So, got the new manifold and it was good for a few weeks.
Now, starting the other night, Friday the 13th, it threw a CEL when I was coming into the driveway. It had been throwing a code every once in a while, and I brought it to school to scan it Friday the 13th but there was no code. So, I assume that it is an intermittent problem, no big deal. When I go to get in my truck to go to work a few hours later, the 5.4 cranks... and cranks... and cranks.
I get it to fire up, and it dies again. Run codes, and it says that the cam positioning sensor is broken. Replace both of them, still acts up ie. doesn't start when it does start it runs very rough and stalls. Get it up to my uncles shop, and replace fuel filter.. Still runs like trash. Run codes now, and it says rich/lean in bank 1.. My uncle tells me to move my truck out of the shop, so I start it up, and it runs great. No hiccups, it idles perfect as I move his truck out of the shop first.
I park my truck outside and let it idle for about 10 mins, and when I come back out it is still idling, perfectly fine. I get in, put it in reverse, and get about 20 feet when it dies and will no longer start back up. What could be going wrong?! Sick of throwing money into this thing! At one time while started up in my uncles shop, it was blowing black smoke, as if it was a diesel!
View 10 Replies
I've got a 99 F-250 6.8L V10 manual 4WD with no speedometer or odometer. The ABS and MIL lights are on. Code is P0500 - VSS malfunction.
This started when the previous owner hooked up some large LED backup lights to the factory wiring. Something smoked under the dash. He then moved them to a relay-switched +12V feed. He reported that the backup light fuse did not blow.
Ive tested the backup light fuse and the recently replaced VSS. Fuse is good and the VSS tests ok for Ohms and gives AC voltage when the tone ring turns. I pulled the fuse panel, GEM, and PCM. There's no visible damage anywhere there. I'm stumped. Tomorrow, I'll dig for any melted wiring under the dash....
View 8 Replies
