Have an 06 F250. When I slow down to make a turn then accelerate it's like the drive shaft spins half a turn before it catches. Been doing it for awhile now. Now I'm get a clunk when I come to a complete stop. When you stop then truck settles there is a little clunk. Does this sound like the slip yoke problem?
View 1 Replies2016 F250 6.7L 4x4
I getting some tranny noise when towing on incline from a complete stop. When I slowly press the gas pedal I hear grinding noise. If i press the gas more my truck starts to move and the noise goes away. It doesnt happen all the time. This started right after my 1000 miles recommended break in before towing per ford manual.
My truck now has 2800 miles and the grinding noise occurs intermediately regular driving. Mostly on steep incline or decline. I haven't taken it to the dealer yet because I cant recreate the issue all the time.
I have a 2000 f250 superduty gas v10 6.8L . I bought this truck about 4 months ago. Now when I take off from a complete stop the truck shakes up until second gear, shifts fine all the way up until the last gear it looses power "loosing power" i mean i can put my foot into the pedal and it takes forever to climb speed meanwhile the RPM'S never skyrocket like it the transmission was slipping if anything a couple times the RPM's dropped are stayed the same then as i take my foot off of the pedal once i have my desired speed sometimes not always the truck will give me a little jerk Also Just the other day I was driving on the highway and decide to put her on cruise control at about 70mph, I set the cruise control and the RPM gauge was just over 2,000 and the tach was fluctuating up and down about 1/16 of an inch. I been reading alot of forums and what I got out of them is it maybe pointing me to a misfire maybe the coil packs? Plugs?It's not something major like a transmission rebuilt.
View 6 RepliesI just bought the truck 2 days ago and the power steering is acting up. When I test drove it I noticed the power assist seemed weak but it has gotten way worse over 2 days.
Truck is a 2001 F250 4x4 V10 auto. 60k miles and totally stock except for Harley Edition wheels and stock size tires.
Now at a complete stop the wheel won't turn at all. If I roll it works. Doesn't matter if I rev the engine. It doesn't matter if I'm on or off the brakes. Tires have plenty of air. The pump is quiet and does not make any abnormal noises.
This is terrible because how can you maneuver a trailer if you can't turn the wheels when stopped.
I noticed the fluid was low and not reading on the dipstick. I added a few ounces and that's all it took with no change. I then used a suction pump to empty the reservoir with the truck off. The fluid was very dirty, probably the original fluid given the mileage. I removed about a quart and refilled it with fresh Mercon ATF. I also changed the serpentine belt because I noticed the belt was probably the original and was cracked.
It went away briefly tonight as I was playing with it. I thought I fixed it but I was fooled. What I did was remove the reservoir cap and turn the wheel from lock to lock while rolling forward slowly. Suddenly it was fixed . But 5 minutes later the problem was back.
250 2006 Superduty v10. Codes p2106 and p2135 ... Only occasionally when coming to a stop it shudders like it would stall. It happens for just a few seconds then ok again but wrench light comes on. After the next shut off and start the light goes out. I had the throttle control position sensor checked and they said it was ok. Got a software update at Ford. I hate to just start replacing expensive parts. I have about 60000 miles and it is a great truck otherwise.
View 1 Replies1999 F250 SD Ex 4x4 V10 has been intermittently not starting, both cold and warm, began last fall but only happened once a month or so or longer. Would then start after trying again either right away or after waiting a bit. Now it is doing it on a regular basis. Sometimes it will start right away, sometimes won't but if you keep trying or wait awhile it starts, sometimes using the extra key will start it right away after the first one didn't, sometimes neither one. It does not try to turn over, make any noises, no warning lights flashing, just won't start.
Now also on two occasions within the past week, it just stopped while driving. Radio, dash lights, etc., stayed on. I got it to the side of the road with the little power steering left where it started up again right away.
No codes showed up. First mechanic couldn't find anything obvious or replicate problem. Changed air and fuel filters (fuel filter really needed changed), plugs. Got truck back and it wouldn't start next morning. He checked it again and got a code related to ignition, tried the spare key and it started up. Truck back home, next day same problem.
Mechanic 2 checked, no codes, kept several days but, of course, couldn't replicate problem. I'm not even sure what all they checked, used to be an excellent repair place but now they seem to only really on diagnostics and throw up their hands, very disappointing. Replaced solenoid and starter last year myself. Otherwise, have had no problems until this.
I have a 2002 F-250 7.3 Powerstroke 4x4. My truck has developed a "clunk" for lack of a better term when accelerating from a dead stop. It is not a shudder as it only happens once within a few seconds of depressing the accelerator and then goes away until the next time I stop moving.
It feels like either something in the drivetrain is not engaging right away, or something is releasing, like a stuck caliper or something. From the way it feels and what I've read so far about the TC/Trans, I'm assuming it is something worn in the drive-shaft/rear diff.
But it needs brakes badly (already have all new rotors & pads ready to install) so maybe a caliper is sticking when depressed and then popping loose under initial acceleration? I think this is unlikely but possible.
While in Tow/Haul with my 5th wheel when slowing down probably at 5 or 10 mph the last downshift is very hard and the brake pedal gets real soft until full stop. Afterwards the brake pedal is firm. Tow/Haul without the trailer is fine. It's an '06 F250 Supercrew 4x4.
View 6 RepliesJust moved into the 250 from years of 150's. Now have 98 miles and read that the tran would have noise but normal while breaking in.
whats normal, not used to this much Clunk while changing from P to D ect. More noise than used too I guess.
3.73 gears
2014 F250, 6.2 gas 2wd....
I have a 2004 f250 with some front end troubles. When turning right once in a while it will make a hard CLUNK noise and then trying to drive down the street it drifts over to the left and I pull the wheel back to the right and when I turn the wheel it feels like I like theres something hitting somthing else in the front end. I have checked ball joints and tie rods and they are all nice and tight. Some stuff I have done that probably isn't related to my problem is shocks and sway bar end links. What this could be? Hopefully not the steering box!
View 7 RepliesI have a 2005 f250 that has a wander and a clunk what feels like under the drivers seat. The driver side bushing in the radius arm has no dirt and looks like wear on it compared to the passenger side which is completely covered in dirt. My question is, bushing wear out will cause wander and a clunk. Is it hard to replace?
View 3 RepliesWhen I go over good size bumps, I hear a clunk in the front tire area when my driver's window is down. It's a metal noise, like something loose.
2011 F-250 with 203K miles. Replaced shocks last year. Did this with stock wheels/tires. Something in the front suspension or axles. What should I be looking at?
Every once in a while, while driving my 06 350 SRW at slow speeds, I hear a grinding noise coming from the left side of the truck. It is almost like a winding grinding noise if that makes sense. It will grind slow to a stop, and then I hear a clunk.
This is a very intermittent problem. The tires are completely shot on the truck, and I thought that would be it, but considering it is intermittent and the clunk I hear as I come to a stop I figured it could be it.
2012 f250 SC xl 6.2 - Is it normal to hear a single clunk sound on occasion when accelerating from a stop sign? Doesn't happen all the time mind you and I don't ever remember hearing it in the past.
Now just today, while backing up my driveway, as soon as I started the reverse motion, I heard the same clunk. Sounds like metal to metal and comes from the rear of the truck.
Only 7000 miles on her and I treat her like a baby...anything I should be concerned with?
As the title says are my front leaf springs bad? I got this truck 2 years ago and replaced all the ball joints, shocks, sway bar links,front hubs, rotors and brakes along with all the seals. I have a clunk in the front and I can't figure out what it's coming from. Could my leaf springs be clacking together? Truck
is a 2000 F250 SD v10.....
Driverside front
Rear spring
My rear wheel bearing are a little loose. This afternoon while diagnosing a squeak in the back I found this. While pushing the truck side to side there is a clunk and when you lay your hand on the tire you can feel it, bearings are loose. Nothing during the operation of the truck to give this away, truck runs and drives as it should but I need to check it our before something does go wrong. What I'm looking for is a torque / preload that the rear wheel bearings need to be set at.
View 2 RepliesMy issue, just purchased f250, 2004, v 10, manual transmission, state vehicle with 32,000 miles but was a plow vehicle for localRMV lot, that said, great shape and runs strong but I get a clunk and shutter when I am in reverse and only when I push down clutch before stopping. Doesn't do it starting forward or reverse, only reverse and when I push clutch in before stopping. Did have a friend drive and looks like the transfer case is moving, as if mounts or bolts are loose. Does this make sense and could bad slip joints be putting excess torque on ?!?!?
View 4 RepliesI have a 02 F250 4x4 5.4. As I drive and when pulling into a driveway I hear a clunk that can be felt in the floor and the steering wheel. I've replaced the wheel bearings and seals, shocks, ball joints, sway bar links and bushings, tie rod ends at the gear box and "right hand inner". The other two tie rods are tight and so is the track bar. I cannot duplicate the sound if I jack it up and move parts around with a pry bar. I can however move the steer box sector shaft upwards about an 1/8. I've adjusted the screw but it didn't do anything. Could it be the steer box or the springs? I've even mounted a GoPro underneath but everything moves and I can't tell why it is.
View 14 Replies2007 F250 4WD 5.4l ... when I turn sharply in either direction I am getting a light clunk sound similar to when you are in 4WD on blacktop and try turning. The engine also seems to wanna stall when I cut the wheel too sharp.
View 4 Repliesi just bought a 99 F250 4WD with the 5.4 in it i put a brand new starter in it. When i turn the key to try to start it, it just cranks the motor once and stops. The starter isn't grinding or clicking, the motor clicks once and move the belt and pulley a little but that's it. What would cause this?
View 13 RepliesI have a 2001 F250 V10. It idles around 1k and when stopped at stop lights or when put in reverse it stalls. I have replaced IAC, fuel filter, tranny filter, oil filter, plugs, coil boots, tranny fluid, oil, air filter, and PVC along with the PVC hose. I'm totally stumped. It doesn't stall if I do a rolling stop.
View 14 Replies