Ford Super Duty (1999-2016) :: 2006 5.4l Runs Rough For About 10 Seconds When Started
Jan 4, 2016
Have a 2006 F350 5.4l that is mainly used as a plow truck. I drive it at least once a week when not plowing just to make sure it runs ok, etc. Only put on about 2,500 miles per year. Keep it in good repair - not by me, but by the dealer or mechanics.
Problem - last two times I started it, it started ok but runs real rough for about ten seconds. Sounds like the engine is going to die. After about ten seconds, it "catches" and runs normal. Have no problems when driving it. If I restart it, it doesn't do this, so it seems to only happen when the engine is cold.
Battery was brand new back in Sept. All plugs were replaced maybe 3 years ago, as was the cat converter and muffler. Run non-ethanol fuel. What might be causing it before I bring it in.
View 6 Replies
Advertisement
Ok just bought this truck ran fine. Put a sct tuner on that the truck came with and some how got the egr turned on. It had a egr delete so it was smoking and finally found it out that it had turned on but fixed it. Now we have another problem, it will start up and run fine and about 45 seconds it will start running rough and go into a limp mode. It will run rough and starts to die slowly and when it starts to die there is no throttle at all.
View 4 Replies
2006 E-350 Dually Ambulance Chassis with the 6.0... Approx 125000 miles.
Recently, the truck started an issue. its an every once in awhile thing but has been doing it more recently. The OD light will start flashing and the vehicle will start to have clunking in the tranny and start shifting rough. ABS kicks in making it hard to stop. Once you turn the truck off and back on, Its fine until it does it again. Im connecting to a scanner tomorrow to see if i get any codes.
View 14 Replies
I have a 2006 E350 van, just recently had passenger side injectors replaced along with dummy plugs and stand pipes. I was at the car was spraying it off and noticed it started running rough, just figured maybe some water made its way into the engine bay and something got wet as it was running great. Well its stayed that way and i am getting codes p0264 and p0276. Digging around on the net seems like its ficm or wiring, ficm is 48 volts and 13.5 volts, connectors are on tight and i dont see any wire chaffing kinda stumped. hoping its not 2 bad injectors at once.
View 2 Replies
My truck started running poorly with an intermittent miss about 6000 miles ago. The miss gets more consistent when the tank is below 1/2. Fill it up and the miss goes away. No codes, shop that does a lot of V10 camper work could not figure it out.
My guess is that the fuel pump is going out and it overheats when the tank is low. The problem is getting progressively worse. Now it misses slightly with 3/4 tank and even a full tank sometimes.
Plugs have been changed, fuel filter has been changed, and the shop found 3 COPs that were bad before all this new intermittent miss started. The truck runs ok at wide open throttle.
Am I just nursing a bad fuel pump that will leave me standed soon? Truck has 170,000 mile with original fuel pump.
View 14 Replies
2004 F250 V10, runs good until it warms up whether it's hot or cold outside. While on freeway, it really shakes while cruising, but of you get in the gas enough for a kick down, seems to be pretty smooth. I've changed the coils, and 9 plugs (one wouldn't budge, but the others I took out looked fine) to no effect. Where else should I look? Also, no CEL, and no codes, which seems odd as bad as it feels...
View 11 Replies
So, my truck runs really rough when I am @1500 RPM and lightly feather the gas. I have replaced all coils and plugs. Used dielectric grease. Replaced air filter, replaced ICU, changed transmission fluid. The thing still "shudders" ... 2004 f250 5.4 ....
View 14 Replies
I just bought this 99 f250 7.3 Powerstroke last week.. drove it all week fine, I car pool with a family member to work and asked his girlfriend to plug my truck in for me, well she didn't and it had stalled on the way home one morning but started up after cranking a few times i thought nothing of it. Drove it a little bit that day and it was fine, while I let it idle in my drive way as I prepared to go work it started running really rough then died. It took a long time to start again..now it's happening all the time. I changed the fuel filter and someones telling me there's air in the lines..
View 5 Replies
Getting these lean codes P1131, P1151, P0171, P0174. I was getting a knock sensor code before but not now. It will not idle it just dies and runs rough till I get at higher rpms gotta feather the brake and gas to go anywhere.
View 5 Replies
I was driving my 99 f250 superduty and out of no where it sounded like i had blown a tire started to shake for at least 3 or 4 seconds pulled to the side of the road got out and check tires were good, got back on the road with no more problem.
View 1 Replies
2002 f-350 diesel 4x4 7.3l. It stalls out a few times lately( and starts right back up) and it runs rough like there is an air bubble then smooths out. Changed 1 fuel filter and the pcv valve. 96,000 miles.
View 6 Replies
I have a 03 250 5.4 with 160k. I just recently replaced #4&3 coil packs. Truck was running great again. Then a few days later the truck was running extremely rough and white smoke from the exhaust. I noticed the pcv valve was not all the way in(pretty much out) put it back in and ran fine for two days now running rough every now and then and the pcv valve is making a vibrating noise but stops if I pinch it slightly. I did replace the plugs a year ago.
View 14 Replies
Let me start with I have a 2003 f250 5.4. The motor blew on my truck and I had a 100k motor dropped in it. I've put new spark plugs, ohmd out the coils. I tried both sets of injectors. cat delete and new fuel pump. It has rough idle and stalls but runs fine at higher rpms. Also has basically no brakes. I am thinking vacuum but I've check all the lines. No codes either!! also cleaned throttle body.
View 4 Replies
2007 f350. About 2 weeks ago my truck started smoking really bad, and I took it in to have it diagnosed. It was 4 injectors that were bad, so I had them replace all 8 and also install a bullet proof oil cooler. From the moment I got the truck back, it did not seem to idle as well as it used to, and over the next week, it began to blow a good amount of white smoke and run very rough.
But the weird thing is when I took it back to the shop to have it diagnosed, the minute I pulled into their driveway, it ran perfect, and they were unable to pull up anything. The next morning, I started my truck for work and as I drove down the street, the truck ran extremely rough, and seemed to be running in 2 cylinders. I shut the truck down, restarted it and it ran a little better, as I limped it back to the shop.
View 6 Replies
I bought a 1999 f350 v10 about a month ago took it on a 1200 mile trip from Arizona to Kansas. Truck ran great till I got Kansas. The truck started to lope after I got fuel at a fuel station. Did not get any check engine light on. I check for vacuum leaks did not find any. I change all the coil packs, spark plugs, IAC valve and fuel filter. Clean the intake and put sea foam in the fuel tank and the truck still idles rough. Change the egr vavle. Truck ran great till I got 10 miles down the road then the truck started to lope again. So I'm getting really frustrated over this truck.
View 4 Replies
I have a 2007 F250 4X4 6.0 diesel. When first started it idles extremely rough to a point it sounds like a old gas engine missing. But after it warms up for about 15 minutes it runs and idles like a new truck. I'm thinking it's the injectors if so is this something I can change/clean ....
View 2 Replies
I have a 2006 F450 6.0 Super Heavy Duty. The Problem that I am having is when I turn the key it wont crank over. In order for it to start I have to hold the key in the crank position (like i am trying to start it) for about 20+ seconds, and then it will start cranking over. After it cranks over it starts just fine no problems. This only occurs when I start the truck up for the first time each day. After the initial start of the day its fine. (FYI I turn the ignition to the on position and just let it set it still takes me turning the key to the crank position and holding it 20+ seconds).
View 5 Replies
The truck is in my Sig 01 F250 5.4
Just got back from a long trip with it. Parked it for 3 days, all was running fine. Went to dinner Sat night and all was great, left the restaurant and as soon as I started the engine I noticed a slight vibration. As soon as I hit 42 miles per hour, it started shaking pretty good. I pulled over and checked under the truck to make sure I did not have anything I was not supposed to hanging down.
Driveshaft looked good, nothing leaking from rear end or tranny. When it does vibrate, the Tach shows the unhappiness as well. This a.m. driving to work it was vibrating at all speeds and shifting was very rough, had a hard time deciding if it wanted to be in second or third gear. I don't think this is drive train issue... When it shutters and sputters at 40ish MPH, its almost like it loses power and I have to let off the gas. and then under power it shakes badly.
I had the super chip settings for performance tow when this started and then I changed it back to stock settings, thinking it might work, which it only got worse. Changing the settings with the Superchip you have to disable the fuel system and I do this by pulling the fuel pump fuse under the hood in the power distro box.
I think the ujoints are still good, the oil and tranny fluid are spot on. Hubs are locked but in 2WD. Had all the front end replaced 15K miles ago. Brand new tires and wheels in Sept, front end alignment done at same time, front brakes were 90% and rear brakes at 20%.
View 10 Replies
My EGR cooler started to leak last week . Right now I have it , the oil cooler and HPOP out for the updated STC fitting. [9-05 Trk. build date with 2 piece fitting]
Yesterday I pulled the turbo apart to check the vanes .Was throwing a 0299 code for some time . It took half the day to separate the Unison ring from the housing,. Cleaned and freed it up. Unison ring shows no wear .but the mating surface of the turbo housing is corroded and not smooth. Shaft end play is fine.Would not put it back on if I were not selling this truck. Truck has 77,000 miles and in great shape.
How critical is having a smooth surface for the unison ring to mate to?
View 1 Replies
As I am driving everything goes dead radio, windows, dash, alarms, everything then turns on a usually 30 seconds later. is it a ground? is it a sensor that's getting to warm? is it a loose wire? where should I start??
View 6 Replies
Experiencing a melt down with one of my trucks. One of our trucks is an 06 F250 SD with 80k on a 5.4L and the other day the tow/haul light started to flash. I took it to a buddy's repair shop (who is an experienced Ford tech and tranny guy) any way, it shifted fine until about the last 1/2 mile before I got to his shop, then it started shifting in and out of different gears. He found solenoid "A" pressure solenoid failure and one other solenoid failure, he replaced all 7 solenoids and also found the pigtail from the transmission to the wire harness bad as well and replaced that. I pick it up and get about a mile down the road and the light starts to flash again so I took it back, he ran his scanner and now found something with the coast clutch and through all his testing it told him the coast clutch needs replaced. He removed the trans. and tore it all down and found nothing wrong with anything, in fact he said everything looked in great shape and thinks the pcm failed.
View 12 Replies
