Ford Super Duty (1999-2016) :: 2005 F350 Not Starting With P2291 Error Code / ICP Reads 0 While Cranking
Nov 22, 2014
2005 F350 crew cab with 6.0 currently cranks but no start with a P2291 error code. Using scanguage 2 it shows icp 0, IPR 67.7, FICM 47.5 while cranking. Disconnected ICP and still no start. removed icp and hooked up air and I do not hear/see any signs of air leaking. When I disconnect the air it then whooshes out. About 2 months ago got a #1 cylinder contribution error code and changed out that injector and it has ran fine up until this issue.
Can this be a IPR? I am leading towards the HPOP, but as it costs a pretty penny would really love to make sure I tried every other avenue.
I have 197K on it, and 2 years ago did a EGR cooler delete. In May this year replaced the oil cooler, and then in August changed out the #1 fuel injector.
Oil cooler screen was broken. Cleaned the entire reservoir out. Could this just be a clogged IPR? or seeing the change while cranking an indication that it is working?
View 1 Replies
Advertisement
I had a 05 f350 5.4 3v come into my shop with a CEL. Did the usual it had a p0307. So I did the usual again changed plug and coil plug cam out no prob they were done 15k ago. Test drove a few times and it was fine. Few days later customer brought back with same code p0307. thought maybe I got a bad plug or coil so I moved them to #6, misfire stays on #7. When I drive it local its fine when I go to pull on to highway and really put my foot in it CEL flashes (misfire) and it pings like crazy and loses all power. Scan it back at shop and still only p0307!!
View 10 Replies
I have a 2006 f-350 6.0 and i went to fill up my truck with diesel. After that the truck did not start. Currently has the code p2285 - injector control pressure sensor circuit low. I tried disconnecting sensor, still no start.
I have the torque pro app and another 6.0 that I use for comparison. Check power at ficm 48 volt, flp 11.5v, FVP 11.5v. Hpop while cranking shows 1400 psi. removed oil filter and see low pressure oil ok, fills up reservoir. ipr at crank about 65%. fuel filter full of fuel.
Replaced the dummy plug on passenger side because originally hpop was very low psi 12. after replacement it went up to 1400 on cranking. What should I be looking at next, should I be removing ipr? should i be looking at crank sensor or cam sensor? Just installed 2 new batteries also because my dad kept cranking the truck until it died.
Checked to make sure fuel cut off relay not triggered, Ok. The truck has been having long cranks before it died. Also right now the injector cycling is 10 seconds long while on my other 6.0 it is about 4.
View 14 Replies
My 2003 F-250 (gas V8) will always start right up when it is cold. However, once it has warmed up, it often will not start. Cranks fine, but not even wanting to start (like someone pulled all the plug wires) and has left me stranded until I wait for 3+ hours for it to cool back down. Doesn't trip the check engine light, but seems to be due to the engine being hot. What this could be?
View 7 Replies
I have an 08 f350 lariat with the 6.8 with 66000 miles. A month ago took it to the dealer with a plugged catilityc converter. All covered under warranty. Got the truck back, starts great when cold including 18 degrees the other morning. I drive 7 miles to work, shut it off and restart, it acts as if the starter is struggling to turn the engine over. Once it cools off, starts fine again. I took it back to dealer, they replaced the starter. No change. Took it back again, they replace battery. Cranks a little faster, but you can tell it's still struggling. It always starts, I'm just wondering how it will be when it's 80 out and in pulling my 9000lb camper....
View 14 Replies
Wife took truck out and turned around after going less then a mile, saying it was running very bad. We got this truck about two months ago at a state vehicle auction. It was a state used truck, 145,000 miles, 05 Ford F350, ext cab and 8' bed. Anyway at first I thought it was valve tap until research said an exhaust manifold. With a fog machine in rear exhaust pipe we confirmed it was leaking and replaced the exhaust manifold. Figured it was probably a good time to replace spark plugs too. Took truck for a ride and she still buck and farted.
Got a code machine and got P0171 and P0174. Couldn't find a vacuum leak, but your could hear the air being sucked in. went to local parts store, guys couldn't find leak, but they said truck sounded like a steam machine. today I made a homemade smoke machine and smoke came from air intake, figured the gaskets were bad. The pictures show what I saw when I took the gaskets off. The port that has melted is the same port were the exhaust manifold was leaking from. Am in deep "doo-doo". What caused this?
View 5 Replies
I have a new to me 2011 f350 diesel lariat. It came with 18" wheels with the TPMS that I recently sold and purchased a set of 20" 2015 wheels which also have the tpms in them. I am getting the error on my information cluster. I've tried to reset the tpms using the owners manual to no avail. I can get it to go into the learn mode but when I start letting the air out of the first tire the air just keeps coming out and it won't register.
View 4 Replies
It's a 2001 F-350 Crew cab short bed. Got it from the second owner which had a large file from the original owner on documentation and maintenance records. Truck has 280k, tranny about 80k. Question I have is, I kinda thought it would "feel" more powerful then it does. Temp got to about 35f last night after work and it cranked for about 15-20 sec before it started (yes I let the "Wait to start" light go out).
Then pulling out of work it would hardly get out of its own way. Does this sound normal? When it is warmed up it goes ok, but still I figured when the turbo winds up it would feel a bit "peppier". I get its a diesel and not a hot rod but I was expecting a bit more pep.
MODS on the truck that I can tell: AFE cold intake, 5"? exhaust turbo back, about 4" lift. Stock PCM. In cab controlled rear air bags, nice deck with back up camera.
View 6 Replies
I have a F350 with a V10 Triton motor. It has 186,000 miles on it. I have difficulty in starting it after it has sat for a few days. Typically I have to turn the switch off and on multiple times but it will eventually start. Once it has started it runs and starts fine if it has not sat for any long period of time.
I connected a pressure gauge to the schrader valve. Initially when the key was turned on there was no pressure. While the engine was turning over it was about 30 psi. When the engine started it remained at 30 psi. Ran the engine at 4,000 rpm and the pressure remained about 28 psi. Shut the engine off and turned the key back on the pressure showed 20 psi and remained there.
I'm thinking maybe the problem is with the fuel pressure regulator but can seem to find it. I've spent multiple hours searching online for the location of the Pressure Regulator but no luck.
View 6 Replies
I own a 1999 F350 with a 7.3 diesel engine, every time I drive it, it will start once then it won't start again for hours. At first I thought the starter was getting hot because of the exhaust is too close to it but I tested the wires going to the starter and i am not getting power to the starter when this happens. When it started doing this, it would only act up if it was above 80 degrees outside. Now it makes no difference. I have replaced the Valve cover gaskets, glow plug solenoid, and starter solenoid.
View 3 Replies
What this means, how can I fix it? No technical jargon or abbreviations that I will not understand. The error code is for a 2006 F-250 6.0L Diesel automatic. I have a tow controller installed it came with the truck when it was new.
View 7 Replies
So I just bought a 2003 f250 v10 and I've plugged in my code reader and it couldn't get any info, so I took it to auto zone and they got an error code. I took a test lite to each little connection on the port with the ignition on and only got power to some of the metal connections on the port. So I'm wondering if all the little connections should have power? If so where should I start to look to find the problem?
View 5 Replies
I tow 10-15K; 6-10x per month with this truck. I can feel the braking ability starting to drop off so I want to get them done pretty quick. I am more or less happy with OEM performance but if there is a better value, and with my SO starting to haul the horse trailer around.. I wouldn't mind upgrading.
What is worth the money? I'm fresh out of school trying to figure out what the best value is.
Calipers?
Rotors?
Pads?
Brake Lines?
What would provide me with a noticeable improvement without breaking the bank?
Last question, could worn rotors cause vibration/shaking in the steering (primarily when turning ramps) at 50-60mph? Tires are brand new, problem showed up before they were replaced.
View 7 Replies
Engine light and error code for tps occasionally comes on , then stays off a while. parts store said it was ok (shows full range) , but ford has an update for computer to fix. engine is v10 and parts store erased code and it hasnt come back. the only indication that something was wrong is the light coming on and once on the interstate at high speed , then the off ramp slow down, the engine seemed to want to stall as if engine not matching actual speed for a few seconds, then it was ok again. I was out of town and the mechanic that looked at it told me to go to Ford for an update. He tested the tps and said it was ok.
View 2 Replies
2005 V-10... I've found some info on the "fuel level data error" but thought there must be more on this. In the last month or so I get the error on the message center and the fuel gauge goes to E. Happened a couple times here and there and then the CEL has come on. Have nto been able to get the CEL to go out because it happens too often now.
Have tried a couple bottles of Techron because that is suppose to fix it but no luck after about 150 miles. Can't find any loose wires/connectors. Am ready to give up and drop the tank. Is the sensor separate or part of the pump assy? Also don't see alot on dropping the tank on SDs. Any tips?
View 14 Replies
I have an '06 F350 dually with a 6.0 diesel. I bought this used about 5 years ago and for the most part have loved it. i would always smile on the inside when i heard people bash the 6.0...i thought i got lucky....until today.
140k miles. recent oil change. all is swell...until this morning. Stick in key and turn it. glow plug indicator comes on...all lights come on for a few second....wrench, abs, dtc etc....wrench shuts off...glow plug light comes on...4 or 5 seconds later wrench light comes back on....turn key and NO CRANK.
All fuses are fine...starter cranks if i jump the solenoid...but it won't start. Miles to empty and everything else is just dashes hit the OBD and it says "engine sensor data error"/ "trans temp error" ...
View 1 Replies
2002 F350 5.4 . I did some plowing today, truck ran Great, but noticed the Auto Shifter starting to get some play in it, 185 k on it. I recall reading about how to tighten it back up.
View 3 Replies
My 2011 f-350 6.2l cold starts hard, it cranks through 2 cycles sometimes before it fires, then it might stall. Sometimes it stalls if I put it into drive or reverse before its warmed up. It has also misfired on one or several cylinders during startup. It has also misfired while driving. It has never stalled when driving. I have replaced the canister purge valve, I have done a full tune up with all factory plugs. All with no change to how it starts. My next step is a Pcv valve, I have one coming from ford today.
View 5 Replies
2006 F-250 6.0... I'm getting a P0470 error code and no boost, The unison ring is free and clear, the Turbo will not create boost till about 2000 RPM on the road. If I unplug the VGT there is no change in the turbo.
When the vehicle is started there is no tone change in the exhaust. This just started after I replaced a dummy plug in the oil rail. I checked all the connectors as well. I cleaned the EBP and tube.
View 1 Replies
OD light flashes on my 2000 F450 7.3 but still runs and drives shifts fine. If i turn o/d off before i get going then it won't throw the code and start flashing at all. I am going to check the harness again to see if there are any bad wires. If not is it usually a bad solenoid pack i can just swap it out and fix the problem? I have to replace the pan soon so when I do if I need to replace the pack I'd like to do it then.
View 4 Replies
I just got my 2005 F250 diesel out of the shop. The errors codes P0299 and P2263 were listed on the computer. The service done, was to clean carbon from turobo charger and service the EGR valve. I talked with the mechanic and he recommended that I use Cetane Booster Additive. What would the Cetane Booster do? How would it prevent the carbon build-up in the turbocharger? What should I do to prevent turbocharger carbon build-up?
View 3 Replies
