Ford Super Duty (1999-2016) :: 2005 F250 Started Chugging And Check Engine Light Came On
May 28, 2014
I have a 05 f250 with a 5.4 I'm having issues with I was driving along the truck started chugging along and the check engine light came on so I checked it with my bully dog the codes that came up were p0192 which is fuel pressure sensor circuit low the next one is p0452 is evaporative emission pressure sensor switch low also came up with p0191 tonight haven't dug into that yet.
I change out the pressure sensor switch from a buddies truck didn't make a difference put my sensor in his truck his worked fine I clean the throttle position sensor and The maf also put a new air filter on not throwing a misfire code but seems like it may be. A little background on the truck it's a 5.4 3valve with a bully dog tuner, mufflers been removed added straight pipe mechanically that's all that's done
View 4 Replies
Advertisement
You know the "mechanic's fiances truck" problem. I recently replaced the cam sensor in my 05' F250 Gas. The check engine light had been on for a while before that and my truck rode great, however I now want to sell it and I can't do that with a check engine light on. It's got about 85k miles on it.
After replacing the sensor, the light went off for about 20 miles, but it is now back on and my truck seems to miss every once in a while on acceleration or cruising. Some days it's worse than others. The check engine light still says cam sensor, but the sensor is brand new.
My fiance is a mechanic, so I don't know all the details about code numbers and such. However, I want to sell this truck pretty soon, and I would like it to run correctly. His dad (another mechanic) seems to think it could be a coil and wants to wait for that light to come on, but I would rather fix the problem and sell the truck!
View 1 Replies
My dads 05 f250 6.0 PSD. He says he'll take off in the morning and the fuel gauge will randomly drop to empty and trigger the low fuel light, but then also the Check Engine Light will come on. My brother did a code scan and no codes come up. Where we should be looking to remedy this one?
View 14 Replies
Just replaced the alternator in my 1993 Ford F250. How do I reset my check engine light? It keeps coming on after I drive for roughly 5 to 10 minutes.
View 7 Replies
1-11-11 built F250 with the 6.2. 45K miles. Took it to my local HD truck shop to have the code read. The reader said "Evap pressure sensor switch malfunction", "vac above pressure limit wouldn't bleed". He cleared it and it has now come back.
1. Where is said switch located? Is this something I can do as I'm a seasoned wrench but I'm not dropping the tank in my driveway in the winter.
2. Is it in the tank or outside the tank?
3. Has there been any TSBs or recalls on this before I attempt to repair?
View 6 Replies
So yesterday I decided to wash my truck and after taking care of that I took it for a short drive and the tranny started acting funny. Check engine light comes on and the code is P0500 . It calls for a VSS but I cant locate it. Also the fact that it did after washing the truck is making me think its a wiring issue... F250 SD 5.4 4x4 ....
View 5 Replies
My 2014 F-250 is having a repeat problem with an intermittent cell engine light. About 10000 miles ago it happened, and they changed out the egr cooler. Saying it was gummed up with soot. Problem just started up again. Light will stay on for about 3 or 4 restarts then sir off on its own. It's this a known issue with the 6.7? Is there a way to prevent it?
View 7 Replies
Just this morning I tried to remote start my '13 F250 6.7 and all i got was the doors lock and a two honks. The two honks are usually when there is a door left open when you click the lock button two times but all of my doors were locked. After I started the truck with the key and took it out to go run a errand I noticed the check engine light turned on. Could this be connected or just a coincidence?
View 4 Replies
2002 F250 SD 4X4 5.4L. 4.5 inch pro comp lift tire size 305/75/R16. K&N cold air set up. 208,000kms
I know the truck does horrible on gas but lately is been getting worse, maybe I am getting 350km to a tank. Mixed highway city driving. Sounds like I might have a vacuum leak somewhere but I have no engine light. I've had the truck since last year and put about 10,000km. on it done regular oil changes .. brake maintenance no motor work so far.
View 2 Replies
I have the infamous P0461 check engine light coming up. I filled it with Techron and even purchased Techron additive with a full tank and it's not going away. I've also replaced gas cap with OEM brand new yesterday and light keeps coming on after 2-10 miles.
Truck is stock. Bone stock. The fuel gauge is reading accurately and not fluctuating or jumping or behaving erratically. I checked all fuses and all fuses are good (under dash and on floor in cabin).
2010 f250 lariat 5.4 V8 4x4 super cab 189,XXX miles.
View 2 Replies
Bought a brand new F250 6.7 it has 7000 miles in it now and the check engine light comes on and the truck goes into limp mode. I have taken it in to the dealership twice they said there is no code they can find and they just reset the check engine light and it does ok for a bit then starts the cycle all over again. It also is only getting about 6.5 mpg....
View 6 Replies
2 weeks ago I had the check engine light come up on my 2011 F-250 6.2 XLT. Did a diagnostic check and Codes P2098 and P2272 came up. Did some research and found out the second O2 sensor on passenger side had gone bad. I replaced it with a Motorcraft O2 sensor and cleared the code. It has not came back since. But still not getting the fuel mileage I got before. What else could be wrong?
View 5 Replies
I had a can of fuel at home that had been siting around a while but I put it in my 02 F350 with the 7.3. hind site being 20/20 I shouldn't have done that. The truck only made it about 2 miles then started chugging and eventually quit. So I pulled the truck home and this is what I have done so far. I assumed that I had bad fuel so I started with a new fuel filter. I did notice that the fuel in the bowl was a milky white color. Not sure what that means. But the new filter did not work as the truck will not start. So after reading some other posts I decided to drop the fuel tank and clean everything.
I did that including cleaning out the 2 screens in the fuel pick up. After re installing the tank I put new clean fuel in the tank and primed the truck. But before starting it I drained the first amount of fuel out of the filter bowl just to make sure I got all of the bad fuel out of the lines. So after doing this I put a new filter in and primed the motor again. I appear to be getting good fuel pressure and the fuel looks very clean now at the bowl. But the truck does not even attempt to start. It turns over just fine but will not start. Some advice I can get before I have it towed to a shop. Also, the truck currently has 305,000 on it and has run great up till now.
View 5 Replies
OK....my gas cap (5.4 gasser) wasn't put on properly at the gas station. A couple of blocks later, the "Check Gas Cap" notice came on. I stopped a few blocks later, and installed the cap properly. The notice STILL came on. After messing with the cap 4 more times, I gave up, but the notice is still on. Do I need to have it "erased" like a code, or is there a problem with the cap? Everything LOOKS fine...
View 2 Replies
Experiencing a melt down with one of my trucks. One of our trucks is an 06 F250 SD with 80k on a 5.4L and the other day the tow/haul light started to flash. I took it to a buddy's repair shop (who is an experienced Ford tech and tranny guy) any way, it shifted fine until about the last 1/2 mile before I got to his shop, then it started shifting in and out of different gears. He found solenoid "A" pressure solenoid failure and one other solenoid failure, he replaced all 7 solenoids and also found the pigtail from the transmission to the wire harness bad as well and replaced that. I pick it up and get about a mile down the road and the light starts to flash again so I took it back, he ran his scanner and now found something with the coast clutch and through all his testing it told him the coast clutch needs replaced. He removed the trans. and tore it all down and found nothing wrong with anything, in fact he said everything looked in great shape and thinks the pcm failed.
View 12 Replies
Driving to work the other day my transmission shifted down and the transmission light started blinking. It felt like it geared down like it was in 4x4 I was doing about 55 at about 2600 RPMs. This has happened twice now and lasted around 2 minutes then stopped and ran great.
View 2 Replies
I have had the ABS light on for about a year now. I looked thru the forums and found that the typical reason if a faulty rear VSS (vehicle speed sensor). I found a replacement part online and got it ordered and replaced the original part. Simple 5 minute fix, but it didn't fix it!
Now when I get in and start the truck the ABS light is off, but after I drive off about 20 yards the light comes back on and stays on.
The other day someone stepped out in front of me at a cross walk and I hit the brakes pretty hard and although the truck stopped in time, the rear wheels locked up, so I'm thinking the issue is at the rear.
View 5 Replies
I have a 2007 F250 4X4 6.0 diesel. When first started it idles extremely rough to a point it sounds like a old gas engine missing. But after it warms up for about 15 minutes it runs and idles like a new truck. I'm thinking it's the injectors if so is this something I can change/clean ....
View 2 Replies
Dome light (and bed light) won't shut off. Been browsing the forums for similar problems but most of the time it is the door switch issue. I have my doubts about this since the 'Door Ajar' message in the instrument cluster is not brought up, unless a door is actually open. Similarly, when locking the truck and doing a door check, I get only one beep, means all doors are shut. 2005 Ford F-250 Lariat....
View 3 Replies
I am wondering IF THERE ARE ANY CONNECTIONS WITH TOWING AND THE ABS LIGHT coming on? I just did 360 mile round trip on I84 and I 81 in western NY and eastern PA with decent hill climbs (some with 6% or so grades) - think coal country. I was pulling 8,000 or so pounds (trailer with a jeep on it).
On the way out, the ABS light came on. I pulled into a rest stop and shut her down for a bit. I had been driving on this terrain for the better part of 2 hours. I restarted and the ABS light turned off for the balance of the trip. It was cold (in the 20's) outside. On the return trip 2 days later, the same thing happened after 90 minutes. I stopped again and restarted the trip which turned off the light. This time, the light came back on 10 or so minutes later.
This is the only occasion when my ABS light has come on.
2005 F250 Crew Cab SuperDuty 6.0L
View 4 Replies
2005 F250 4x4, manual locking hubs, ABS light stays on. Plugged it up, front sensors had a bad signal. Replaced both front sensors, still had light. Pulled out the sensors, cleaned the sensor rings the best we could with a little screwdriver. Installed the sensors, cleared the codes. Drove the truck a few miles, light came back on. Plugged it up, same codes. Removed the sensors and there was grease back on the sensor rings. Cleaned it up again, ran through the motions, drove it, light comes back on. Is there supposed to be grease on the sensor ring? It keeps coming back in every time it is driven. My next guess would be the hub bearings are going bad?
View 4 Replies
