Ford Super Duty (1999-2016) :: 2005 - Start Up But Stalls - Won't Run?
Jun 12, 2013
I have a 2005 Ford F-350 service truck,,it has a 5.4L 3V gas engine and has 159869 miles on it. No codes!! Truck starts,,idle races up to 900-1000 rpms and begins to drop to 5-600,,it will just bog or CHAAAAWWWWW if you touch the throttle,,let off and it will most times stall. It is unable to move the truck,,,,start it up and for a slit second it acts as it will rev up but fails and just goes CHAAAAAWWWWW out the intake. I just dont know where to turn on this deal,,Richie 1-774-406-7289 or [email protected].
View 10 Replies
Advertisement
As a follow up to my problem of intermittent stall and hard start, it is getting more pronounced. Now, every once in a while, it will start. Mostly it will not start.
This morning I connected an OBD2 meter with the key on and engine off. It told me that there are no DTC's. As I was attempting to run enhanced DTC's the code reader lost link with the computer. The connection icon was on but it lost the link. At one point, after several tries, I got the link back but it didn't last too long before it was lost again.
This is the same symptom that I have with running the engine. It will run and then shut off. After a hard start, it will start and run just fine and then shut off again.
My question is this. Can I still have power to the PCM and loose power to the processor? Is there a fuse or relay that could be causing this problem? If not, could the problem be a faulty PCM.
View 3 Replies
I just bought this 99 f250 7.3 Powerstroke last week.. drove it all week fine, I car pool with a family member to work and asked his girlfriend to plug my truck in for me, well she didn't and it had stalled on the way home one morning but started up after cranking a few times i thought nothing of it. Drove it a little bit that day and it was fine, while I let it idle in my drive way as I prepared to go work it started running really rough then died. It took a long time to start again..now it's happening all the time. I changed the fuel filter and someones telling me there's air in the lines..
View 5 Replies
1999 Ford Triton V-10 engine, after changing Oxygen sensors, all vacuum hoses and Mass airflow sensor,(also replaced another sensor but can't think of the name of it right now) now I don't get the codes but engine will start and idle but if I give the engine gas it bogs down and stalls. Vehicle sat in my driveway for 3 months, I got it started and drove it once about 30 miles filled up my gas tank thinking gas could be stale, but now it will not run.
View 5 Replies
So, when trying to start my vehicle it doesn't even turn over. Just clicks continuously. Both of my batteries are putting out 12 Volts. I tried the old arcing my solenoid with a screw driver while key is in on position and I got a couple of turns, but it wouldn't completely turnover. My solenoid has power going to it. Checked all fuses that could coincide with this issue. Not sure where to go from here. I have an 05 Ford F-250 XLT.
View 7 Replies
Over the last two weeks I have had an intermittent no start on my 2005 F350 6.0. on four different occasions. With enough cranking and charging batteries it would start again. I am running a scangauge, during these no-starts ICP was at 200. I pulled the IPR and the screen was damaged so I ordered a new one thinking the IPR would fail intermittently. Replaced the IPR last night with a new one, and truck ran great. Started it three different times with no problems and let it run about twenty minutes.
This morning, another no-start, but IPR is at 1162 psi now during cranking. I am thinking fuel delivery now, but have not yet checked fuel pressure, I need to find an adapter for the M12-1.5 port on the secondary fuel filter.
Details: 2005 F350 6.0 SRW 150,000 miles 4x4
Studded a year ago
New oil cooler a year ago
Upgraded STC fitting a year ago
Coolant system flushed and coolant replaced with ELC months prior to cooler change
Coolant filter installed months prior to cooler change
EGR Delete
Scangauge II
Plenty of Oil
New Motorcraft Fuel Filters
Fuel Filter Bowl fills fast during KOEO
LPO registering on dash gauge during long crank
1162 PSI ICP during crank
37% IPR during crank
FICM voltage 48 - 47.5v during crank and run
Batteries tested good last week
SYC = 1 (last night while running)
Codes: Threw a code this morning during long crank "P2614 - Camshaft position output circuit" - One forum stated that this code will appear during long cranks - don't think this is my problem. This is the only code that it has kicked out during this issue.
Fuel Pressure = UNKNOWN
View 2 Replies
I picked up my 05 F350 dually 5 speed w/ the 6.0 powerstroke motor in august... It only had 38k on it when I bought it... its got 43K miles on it now...
Ran great in the warm weather but ever since it got cold out its been a struggle. It was running rough on the way home and kept stalling while i was driving it.. (acting like it was starving for fuel).
I went and replaced both fuel filters and started the truck... let it warm up and it stalled while sitting in my drive way and haven't been able to start it since...
I have fuel additive in it but since I don't drive it all the time (maybe 3 times a week for 30 miles) could it be possible that the fuel is gelling?
I was going to check the EGR valve tonight...
View 9 Replies
I have a 2005 ford f250 super duty 5.4L the problem am having is the other day I took the truck out the yard an parked it across the street. 2 hours later I went back to move it it would not start the engine just kept rolling over I did this for about an hour it still refused to start. 2 days later I tried it again it started without any problems. I put a code reader on it it said P0453 fuel tank pressure sensor. If that is going bad would that cause that problem or would it be another cause.
View 2 Replies
I have a 2005 f350 6.0 has 585000. Installed new hpop and lpop and new ipr .pressured oil system with air don't hear any leaks. After truck done started then put truck together no start same problem as before. No oil pressure on dash. All checks goqd except not enough high pressure.
View 2 Replies
I have a 05 f250 6.0 that currently will not start and no smoke. Replaced batteries and tested ficm. At initial injector buzz voltage drops to 18.8 then jumps back to 48.8 and drops again to 18.8 while cranking. My question is if the voltage is this low does the pcb still just need a resolder or are there components that will need to be replaced?
View 1 Replies
I have a 2005 F250 with the 5.4. This truck has been one thing after another, as you can tell from my other posts. The problem this time is, if it cranks hard to start because it's cold(can be anywhere from as high as 32, but usually in the teens) it will start just fine, then several minutes later throw the check engine light. Put the scanner on, like clockwork, 4 codes, always cylinder 1 misfire pending, misfire on first 1,000 revolutions pending, cylinder 1 misfire confirmed, misfire on first 1,000 revolutions confirmed.
Sometimes you can hear a slight lope in the idle when it does this. Clear the codes, runs perfectly fine. It will never do it after it's been started for the day. Some days you would think for sure it would throw it when it's frigid and the winds been blowing on it, it doesn't bother, other days you wouldn't think it would, and it does.Can the computer think that since it didn't start right up, it misfired?
View 9 Replies
2005 f350 crewcab 6.0 sprayed engine down with degreaser and hosed off 4 days ago wont start have dried and blown everything out still nothing....
View 3 Replies
Having problems with a slow drain on batteries? My truck wouldn't start after sitting for 5 days.
After recharging and starting it up once, I pulled the key, and disconnected the battery harness and checked for current on all the red wires in the harness. Only one drew current. I found the small red wire on the drivers side initially draws 470mA for 1 minute, then draws 22mA. In my experience in mobile audio, 22mA can drain a battery over several days.
Has anyone out there checked their 'dark current' draw? I have chased it all over and checked all the aftermarket add-ons and it comes down to something in the factory dash.
View 8 Replies
I have a 2005 F250 , 4.2 tdi diesel. I just bought the truck recently and still getting to know it.
I noticed recently that when I turn on the key, the vacuum pump starts running and does not go off. It seems to run continuously and will only shut off if I block the white outlet pipe with my finger. Is this normal or is the pump stuffed.
View 6 Replies
Pulled into parking lot this morning, 05 F250 CC 4x4 V10, truck starts dinging at me, Park brake light comes on. Ease off of gas and idle around to parking place, no sign of brake drag. Release Park brake, no difference, set the brake and release, no difference, guess the microswitch went bad. Not raining, never hit a bump, MAY have had my foot on the brake, but that shouldn't effect the P Brake.
After setting for the 12 hour shift, all is good and well. Did not come back on.
Where this switch is? Is it under the cover by the foot set or under the truck along the cable? Would like to know where to look next time this comes up. Did have 2 new tires installed on the front a week ago, new tierod and aligned at the same time.
Just wondering and curious, my last F150 had all kinds of electrical germlins in the windshield wiper arm.
View 8 Replies
So I'm new to this, but heard that there a lot of great people on here that have tons of knowledge. So here goes. I have a 03 7.3 f250. I'm have trouble with the first initial 20 minutes of the truck starting. It starts fine but if I throw it drive and start to go it's shakes bad runs horrible and will sometimes stall out. If I let it idle for 15 to 20 minutes first and then drive it it runs perfect. I have replace the fuel filter, and air filter. The truck has roughly 125000 miles on it.
View 14 Replies
I have 05 F250 SD with 150k on it. The engine has the typical cam phaser knock, timing chain slap on start up and occasionally have a noisy lifter. As long as I use fresh 20-40 oil the engine symptoms are less and the engine runs strong. The motor also doesn't leak or burn oil and the plugs were change out about 20k ago.
The truck is still good and is prefect for my needs so to me it's seems worth fixing the needed repairs. What I would like to figure out how far should I take the motor... just have the chains, guides and phasers replaced or buy a rebuilt motor and swap it? I'm thinking just doing the phases and etc would be 1/2 the cost but may not last as long as rebuilt motor. But realistically I might only put 5-7k miles are year on it anyways.
View 14 Replies
1999 f250 7.3 diesel stalls and pushes while coming to stop. So when I am stopping my truck it will try to keep accelerating then it will die. It has almost push me into a other car in front of me. I can put it in neutral to keep it from dying but it is idling just fine. When I put it back in drive it acts just fine not trying to push the truck.
View 1 Replies
I've got a 2004 f450 6.0 diesel. This thing will start and run great when it's cold. Then when it gets to operating temp, around 190, it will shut down. This is getting worse and worse.
A little history, it was doing this for awhile and a had a few other issues before this. Puking antifreeze, stiction issues, and bad exhaust manifold. Since it wasn't running great I figured why not pull that cab and take care of these issues.
As of last week she got new head gaskets, new exhaust manifold, new injectors, updated standpipes, updated dummy plugs, new o rings on hpop (yellow on the bottom), and a new pipe to the oil pump. I have the old style it's not the stc fitting.
All that work, it still stalls when warm. I monitor with a scan gauge 2. ( Big diesel tech Ron's fan) ...
First thing, give here two second crank start right up, runs better then ever. Gets to operating temp, rev it up, then stalls. Ipc is at 85% ipr gets up to 180 psi.
Unplug ipc, shows 765 psi on the ipr still no start. Put shop air to her and I can't hear any leaks ( probably 15 mins or so).
View 4 Replies
I have a 1999 f250 that runs and drives great but the only issue I have is when I baby the gas pedal it stalls a little and when I give it more gas it's fine or if. I'm going 50mph then let off gas and then baby the pedal it's stalls a little.
View 6 Replies
I recently purchased this 2003 F350 DRW with the 7.3L, automatic trans. Truck has 140k on it. Three times now while the truck has been idling, the engine just died. The first time was a couple of weeks ago when I was pulling out of the driveway. Then again yesterday twice, once while just sitting at a stop sign. Each time it has started right up and ran fine.What is going on here?
View 1 Replies
