My engine light came on a friend of mine did a scan and came up with o2s12 showing low voltage.we need to know which side and location of sensor..the truck is a 2005 ford f250 super duty 5.4l.
View 2 RepliesWhere are the door sensors located?
The ones that turn the light and off when you open and close the doors.
It use to be switches on the old trucks and cars.
But on my 2006 F-250 I can find anything that seems to do that function, nor is anything mentioned in the repair manuel.
I need a replacement driver side door, towing mirror for a 2011 Ford F250 SuperDuty with turn signal, heated, electrically adjustable manual-extend and manual fold options. The truck VIN number is 1FT7X2B67BEC96261. The truck also has an Outside-Air-Temperature indication which is what I'm not sure about. It is my understanding that the Outside-Air-Temperature sensor may be in the side mirror. Looking for any info on the temperature sensor located on this truck? I found an aftermarket mirror while I can not afford Ford. However, the aftermarket mirror ad says it does not have Outside-Air-Temperature and I would like to keep that working.
View 1 RepliesWhere this sensor is? I am trying to mount a front bar and need to know if I can drill thru the tube behind the bumper ( this is the one that is right behind the plastic trim piece.)
View 2 RepliesTruck is 2012 F250XL single cab 6.2. Where is the pitch sensor on this truck? There are times the hill start assist will keep the brakes applied on level ground, and occasionally I will crest a hill onto a level stretch and the truck doesn't want to upshift. So I am thinking the pitch (incline) sensor needs recalibrated. Where it is?
View 7 RepliesMy truck has a bit of an interesting trait. Unless it's just about freezing, my transmission is just about always at operating temperature. If it's 50*F outside and I start the truck, the Trans temp is smack dab in the middle. If it's 30*F outside it starts just a little above cold then is "warmed up" when I drive it down my short street block, which ain't right.
All the rest of the time, it's always reading middle of the bar temperature. My old 5.4L never did this. My 7.3L does. Best I can tell is it's a fault in the temperature sensor for the transmission. I don't have a scan gauge yet to get the readings but will be getting one. Just need to know where the sensor is at so I can have a starting point.
I have noticed my trans temp gauge needle is dead center of the gauge even on a cold start. I thought my sensor was under the pan so I pulled it and did not see any sensor at all. Is there a external sensor?
View 5 RepliesI got an f-350 drw it is sluggish on take off feels like a miss. Higher speeds when you step on it. It seems o.k I have been told it could be a crank shaft positioning sensor any in put on this. I have changed the fuel filters, cleaned the e.g.r. valve and yes it was pretty clogged,air filter seems to be good. And 1 last thing for now where would c.s.p.s. be located...
View 4 RepliesMy 2005 F250 started stuttering, lurching, having wild swings in rpms, nearly dying at stop signs, no pickup when stepping on the gas, then taking off like a bat outta hell. After reading many, many posts here and on other sites, I have concluded that the most likely culprit is the ICP sensor, so I picked one up today (along with a EBP sensor - another story). It appears from the many posts that I have read that Ford/Navistar have frequently changed the location of these sensors. My question is: Where are the ICP and EBP sensors located on the 2005s (actual manufacture date is 07/2004)?
View 6 RepliesI have a 2005 f250 with a 5.4l 3v. Where the pcv valve is located is it in the valve cover or attached to the intake and what does it look like? I have pulled the hoses off both sides but I have not found it let.
View 3 Replies2005 Ford F-250 6.0 FX4 Quadcab
Where is the cord to plug in to heat injectors on this model? Or does this model not come with the cord to plug in?
I recently picked up a 2005 f250 SD 5.4 4x4... I was having issues with sporadic shifting and wandering shifts while cruising around 100kph, scanned it and came up with p0721 OSS sensor circuit performance fault.
I checked the harness and all looks fine, now I attempted to remove the OSS at the rear of the tranny, got the 8mm bolt out however could not, for the life of me get the sensor out. I tried not to use pliers to twist the sensor or anything for fear of breaking the sensor off and having bits go into the transmission.
(The truck is a 05 f250 with a 5.4l). The problem first started out with the engine temperature gauge spiking and then resetting itself when the truck is turned off and then turned back on. If I drove the truck for any distance it would go into limp mode and the CEL would come on. The code was p1299, which is the cylinder head temperature sensor, and I replaced the sensor but no luck. Then the shop and I went through all accessories hooked up and couldn't find a short until I remembered that my prodigy break controller would occasionally read "ol" or "sh" which both readings are from shorts. I tow a enclosed trailer about 85% of the time and the past week I have been towing it with a different 250 and the same break controller without a problem so I have eliminated the trailer. But the shop just said the problem was the controller and unhooked it.
Now the next day it threw the same code with the controller unhooked and the trailer hooked up. after thinking it seemed that it was happening when i accelerated so I took apart the 7 pin and sure enough there was a little water in it, but after driving it around for a little and no code being thrown I hooked my break controller up and it still was showing ol or sh so i believe there is still a short. Also I noticed that my voltage is reading right at 13v instead of the 13.8-14v it was reading before this issue arose. I think I have narrowed it down to the 7 pin harness and/or electrical in the break components, but do not know what would loop back to the temperature sensor.
You know the "mechanic's fiances truck" problem. I recently replaced the cam sensor in my 05' F250 Gas. The check engine light had been on for a while before that and my truck rode great, however I now want to sell it and I can't do that with a check engine light on. It's got about 85k miles on it.
After replacing the sensor, the light went off for about 20 miles, but it is now back on and my truck seems to miss every once in a while on acceleration or cruising. Some days it's worse than others. The check engine light still says cam sensor, but the sensor is brand new.
My fiance is a mechanic, so I don't know all the details about code numbers and such. However, I want to sell this truck pretty soon, and I would like it to run correctly. His dad (another mechanic) seems to think it could be a coil and wants to wait for that light to come on, but I would rather fix the problem and sell the truck!
So I just replace my Cat. Converter with all new sensors in them. I just replaced my spark plugs. (I'm knocking out these check engine light problems) and I think I'm getting close to the root as to why these other parts went bad. Why my o2 sensor would be stuck on "lean" ....
View 5 RepliesMy Bank 2 Sensor 2 oxygen sensor is faulty and I need to replace it. The guys at the parts store were pretty certain it is downstream driver's side, but I just want to make sure before I PB Blasted and removed it. 2008 F250 SD v10 ....
View 1 RepliesBesides the window tag and the door tag, where are other VINs located? The VIN tag in the window looks suspect and there is no door tag. (I covered the first 11 digits of the VIN.) Also, I found a tag on the front pass side of the bed that I've never seen before (mounted between the bed and the cab). What this is?
View 12 RepliesAs luck would have it I'm leaving out in the morn for 600 miles , Noticed a nail in my L/F tire yesterday went too Goodyear they pilled the tire patched it inside.. Then this morn went to fuel up my ABS light stayed on .. Did this last yr. went off after a few days but since the tire was pulled maybe its a bad connection ??? ..Jut want to be sure and scan codes
I want to scan it now to check and reset any codes But looked under the Drivers side dash can not find the OBD connection port looked on Passenger side nothing there either.. Looked under hood around fuse box did not see anything that kind of looked like a port with a cap I'd assume they cap them if under the hood .. Its a 05 S/D 6.0 locate this OBD11 port
2004 super duty crew long bed 2wd, v10 auto SLT.
Manual says not in fuse block.
Looked behind radio, nothing, not even a space or the blue one there.
There are some on the firewall, driver side not marked. No pink wire.
Where else??
Where the battery junction box is? I've been all over under the hood, and dash, and not seeing it. It's not small, since it's full of relays and fuses, and should have a large wire bundle going to it.
View 7 RepliesWhere is the door chime? I just want to remove it. My truck is a 2014 e350.
View 1 Replies