Ford Super Duty (1999-2016) :: 2005 - Idles Rough - Cannot Rev In Park Or Neutral?
Jul 28, 2013
My 05 f250 v10 runs rough at points and sometimes quits when driving. I find it too that I can't rev it in park or neutral and sometimes when it is cold I can. I was wondering if it was a tps or something with the intake...
View 6 Replies
Advertisement
I have a 2005 f250 with a 5.4 3v. I bought the truck with a cracked passenger side exhaust manifold about a year ago. We'll here recently the crack got worse and was giving the code P0171, so I had a shop replace it. I picked the truck up and not even a mile down the road it started idling terrible at lights and had very poor acceleration. And it gave me P0174 this time. It's only gotten worse now it's reading P0172, P0174,P0161, and P1489. I've replaced the spark plugs, MAF sensor, both vct solenoid, an the upstream o2 sensor on the passenger side. I also know I don't have any intake or vacuum leaks, I've had a shop check and so have I. It's starting to get expensive just replacing stuff. So, maybe I have a clogged catalytic converter ?
View 8 Replies
Need this software that would be willing to run a diagnostic on my truck? I replaced all the glow plugs a year ago and the relay a month ago. It idles really rough when it's cold (first start of the day with outside temps even at 90 degrees). It has no power for about 10 minutes. Sounds like an old John Deere 2 cylinder tractor for a few minutes. I have 370K miles on it. After it warms up it runs good. Plugging it in doesn't make a difference. There is no smoke while it is warming up. I have noticed when I accelerate quickly, it blows black smoke (not heavy but when following it you see and smell it).
View 4 Replies
2006 F250 5.4l 4x4, long box, quad cab
Current issue: No overdrive / slipping into neutral / rough going into reverse
Codes: I don't have exact code but will get (p0755)... but shows shifting solenoid B malfunction ( this is the OD/Reverse one) check engine light on and tow light blinking
So whats been done: shifting solenoid B (OD/Reverse) was replaced (used part) inspected valve body and o rings... all good... worked for a week... then exact same issue. Transmission showed no signs of gear damage, oil looks good
Next: Replaced shifting solenoid B again (new one) and transmission wiring harness. Still no change, same codes. Seems to be having a communication issue between transmission and PCM? However continuity of wires and connectors seems ok.
One more piece of interesting info. Every-time before the truck slips I hear clicking coming from the fuse/relay panel under dash drivers side. No clicking no slipping... however never goes into OD at any time.
View 3 Replies
On a cold crank the engine idles rough until it warms or the accelerator is pressed down. Also runs rough going up hills or towing. Check engine light is on and is throwing the code for bank 1 to lean and cat performance below threshold. Cats have been tested, good. Fuel trim tested, good. One mechanic said noth8ng is wrong with it well, there is. 2011 f250 6.2 gas...
View 5 Replies
I was driving on the highway last night when it was like somebody dropped my transmission into neutral. I was cruising at 50mph slight hill. There was no noise or any thing. Now I have nothing.
It's a 2005 f350 4x4 automatic
I can only assume I'll be needing a new transmission but I am hopeful of a small problem...
View 1 Replies
2005 F250
123'xxx miles
EGR delete kit
This is my problem, the truck Idles then revs by itself and throws black smoke.If i leave it on it eventually seems like it floods and shuts off,when i first noticed this it had a loss of power and was having a hard time shifting gears, it would idle fine but when i would try and drive the truck it had no power. I changed the diesel filters and the air filter and the problem persists.
Could this be a bad turbo? Injector?
Here is the video of the problem.. F250 problem. - YouTube..
View 3 Replies
Pulled into parking lot this morning, 05 F250 CC 4x4 V10, truck starts dinging at me, Park brake light comes on. Ease off of gas and idle around to parking place, no sign of brake drag. Release Park brake, no difference, set the brake and release, no difference, guess the microswitch went bad. Not raining, never hit a bump, MAY have had my foot on the brake, but that shouldn't effect the P Brake.
After setting for the 12 hour shift, all is good and well. Did not come back on.
Where this switch is? Is it under the cover by the foot set or under the truck along the cable? Would like to know where to look next time this comes up. Did have 2 new tires installed on the front a week ago, new tierod and aligned at the same time.
Just wondering and curious, my last F150 had all kinds of electrical germlins in the windshield wiper arm.
View 8 Replies
2005 250 5-speed total oil pressure loss ... At 110k mechanic diagnosed failing phasers from noise, rough idle, loss of power under 1k rpm. (Crew cab long box xl bought new for $25k)(first 100k were from carpenters (hard miles) so this truck is barebones and usefulness is much higher than cash value). Truck has 146k
All symptoms typically disappear over 1k rpm so I have limited idle time and manipulated engine speed to try and maintain 1000-1200 and all has been well for past 36k miles. Today noise (valve clatter?) persisted at all rpm and during a scramble to get off the highway all oil pressure was lost (I'm aware that pressure gauge on dash is not 100% reliable). After total pressure loss I cut engine and called tow truck. Out of curiosity, I actuated ignition and motor cranked maybe two rotations, and then appeared seized. After about 45 min waiting for tow I went back to disengage 4wd and take my rifles and skis out of truck. At this time I actuated ignition again and engine fired and ran as it had for past 36k miles. I drove about one mile constantly watching oil pressure gauge, then noise returned followed by instant drop from normal to 0 pressure (dash gauge) I immediately shut of engine.
I am a mechanical engineer, but not a mechanic. I am familiar with the cam phaser system and I understand that their operation is directly related to oil pressure. Today's temp was under 0'F. I have a very skilled mechanic who works for around 30-40% of cost of licensed shop and I know his skills to be on par.
View 4 Replies
2005 5.4l... Its giving me a code p0506 rpm to low idle air control system called for new one they said my truck don't have one said only up to 04 so what now truck idles rough n when u step on it it misses so bad its not funny feels like its laying over...
View 3 Replies
Having a somewhat scary problem.....my truck is already a rough ride due to the fabtech lift and the 37's and you get a lot of feedback through the steering wheel. Its a rough ride down the highway but where it gets scary is at lower than highway speeds like 35-45 range. I can hit a bump and it will send the trucl into this insane cavitation that will literally shale the fillings out of your teeth. I cannot tell if it is in the drive wheels or the front wheels. The best way I can describe it is that its like trying to push a buggy in wal mart with a bad caster wheel on it. It feels like you are about to have a wheel fall off or that its broken off a tie rod or something. Then you simply slow down to a stop and you can drive right on like nothing was wrong. The vibration or shaking does not slow down with the speed. I cannot find anything obvious broken or damaged but this thing is getting dangerous to drive.
05 F350 DRW Fabtech 6 inch lift and 37's. 114k miles.
View 14 Replies
2005 F250 6.0L ... My truck is running really rough when the engine isn't all the way quite warmed up. once the truck is fully warmed up to normal running temp it runs good. I am getting four engine codes. P0672, P0673, P0674, P0676 These codes say 2,3,4, and 6 glow plugs have a open circuit. Can this be the cause of my problem?
View 7 Replies
I have a ford f250 with a 5.4l 2v engine and lately it started to shake when it idles. i have changed all the ignition coils and spark plugs, the injector are fine, but i cant seem to pinpoint the problem. the weird thing is that there are no codes. the fuel trim on bank 1 is around -8 and bank 2 is at almost positive 20 and higher.
View 14 Replies
This happens very often when driving around, at first it was only if i stepped on the accelerator to quickly or braked to hard, the check engine light comes on and the truck idles. Nothing seems to be wrong except when i step on the accelerator nothing happens, it lasts about 5 seconds then the light goes out and im on my way. it has started happening more and more just at random times now. it seems quicken the down time if i pump the accelerator.
Second, it occasionally feels like the transmission slips. I'll be driving and when I accelerate the rpms will go up, then what feels like the tranny slipping and the rpms go down. there is a distinct rocking motion when this happens, but it works if I turn it off and on again, or if i just step on the gas the next few miles it seems to subside.
View 1 Replies
How do I remove the neutral safety switch? I bought a replacement and am having trouble removing it.
After shifting into neutral, I disconnected the connector, then unbolted the two screws. Now I can't get the little white ring that connects the lever coming from the transmission to the actual switch. I have tried prying it off with a screwdriver, spraying a little PB Blaster to lubricate it a little. Nothing will get it off it seems.
I'm leaving to go back up to school tomorrow afternoon, and I need to have this fixed before I leave.
View 2 Replies
The engine was just rebuilt, 7.3L diesel. New bottom end, cam and turbo also new harness for valve covers and injectors, new #8 injector(#8 cylinder lost compression). The engine cranks and idles great. Run it up to 1800rpm - 2200rpm and you get a miss or skip. Almost like the engine turns off and back on very quick, and it makes a clank noise. No codes, reading it with a OTC Genisys 4.0. I also swapped the PCM and IDM with another truck and it still does same thing. Other truck runs fine. Year model 2000 w/ 230,000 miles
View 1 Replies
I have a 99 f350 V10 gas dually dumper. Today while driving I stopped at a stop sign. When I went to continue the transmission seemed to be in neutral, then it caught and I drove through the intersection. It 2-3 seconds later disengaged again. I pulled over. When I attempted to put it in park it grinded. (Bad enough I just turned off the key). I checked the fluid. It was close to full and red. While in park I restarted. Truck started fine. I shifted into drive and nothing. It was like it was in neutral still. I attempted to put in park again and more grinding. Also while in park it does not hold the truck from rolling. After getting towed home I checked the tranny fluid again and it was still looking ok. I drained the transfer case also. The fluid in there was near black an appeared to have a metallic look. Does this problem seem to be just my tc or tranny issues also?
View 8 Replies
I just bought a 2014 F350 from copart and its about to arrive in florida on a transporter. There is no key and no power (flood damaged) and wheels are turned sideways. I am having the transported meet me at a ford dealer so I can get the key made to remove steering column lock. Once I have this, any way to manually select neutral to take it out of park and roll it off the truck.
View 2 Replies
I have a 2013 F250 with a 6.2 L. While driving the vehicle the exhaust sounds nice and throaty. When I put the truck in neutral and rev it, it's quiet, you can barely hear it. Is this normal?
View 3 Replies
My '05 (134k, rwd, V10) has had an occasional issue with stalling when going into neutral. The normal idle speed in park or neutral is 700. In drive or reverse it dips down to 350 or so and then evens out at 500. The stalling is not all the time, perhaps 2 out of 10 shifts. It is slightly worse with the A/C running. Every time it stalls, it records a P0506 error which I then clear out with my ScanGauge II.
I have done some research and have replaced the air filter (super dirty), fuel filter (not sure on how old) and cleaned the MAF tonight. For the MAF, I pulled it from the air tube and gave it a bunch of squirts of MAF cleaner. I did this 3 times letting it dry in between cleanings. I have run a bottle of SeaFoam through it, as well. The idle seems to be very smooth and it pulls my 7k travel trailer without issue. That did get a little better with the new air filter and fuel filter.
I went for a ride tonight and the problem persists. I'm taking it in to have the A/C recharged next week and will have the shop diagnose it. I came across this post which details my issue exactly. The steps are to reprogram the PCM and TCM, and possibly replace the throttle body. Is the reprogram something an independent shop can/should do?
P0506 idle lower than expected on 05 ford f350 v10
View 3 Replies
My 2003 F250 6.0 It started about a month ago and got worse. Let truck idle for 4-5minutes and idle will jump a few hundred rpms. Got worse as it idles and cant figure it out. It eventually died and died once while driving but starred right back up.
View 1 Replies