My 2005 f350 reverse lights just started to not work . So I checked the fuse and it was blown and every time I put new fuse in it blows, where to check. Sounds like a ground issue am I correct .
View 4 Replies2008 F350 6.4 diesel. I have the listed truck in the heading, my #9 fuse which is for the interior lighting, lighted running boards and it is a 15a fuse, keeps blowing as soon as I touch the fuse to the fuse box to replace it. I have look at all the map lights and interior lights and can not find any thing out of the ordinary, all of these light were working fine, also my cruise control and the back up sensors stopped working and they are not on the same fuse and the other components that are on the circuit with the crule and back sensors still work, I know that this is a lot of different things but hate chasing electrical ghosts...
View 3 RepliesI have 2005 F250 6.0 XLT. I was driving the other night and all of a sudden my dash lights went out. I noticed I was being flashed from other drivers and discovered that my parking lights are not working. A preliminary check of fuses I discovered fuse #17 (15a mini) was blown. I installed and new one and upon turning my lights on, the fuse popped again. My headlights and turn signals work properly. It appears I have a wire shorted to ground somewhere on this circuit.
The truck is completely stock with the exception of an aftermarket radio which I installed two years ago.
I checked all the fuses with my test light and they are all correct (both sides of each fuse). I disconnected the gray connector and black connector in the driver side rear of the truck to isolate the issue. New fuse pops as soon as I turn lights on. I completely removed the tail lights, trailer 7 pin connector , completely removed both headlights. I did not disconnect the roof running lights or the mirror lights. I am completely stumped.
I have 1999 ford f250 superduty 5.4 v8 I noticed that my tail lights were not working I replaced the fuse as it was blown break lights worked until i cranked up and applied brakes. I replaced fuse again an checked brake lights they worked fine until i cranked truck and applied the brakes i did notice the wires were hot at brake pedal switch when they worked while not cranked. I replaced the cruise control release switch I was told that may be the problem since cruise didn't work. it fixed the cruise control but as soon as i pressed the brakes fuse blew again.I replaced brake pedal switch didnt fix it.
I then noticed a little smoke under tailgate i looked and the wire coming out of connector was hot while brakes applied and not cranked. i disconnected that wire put a new fuse in and brake lights worked in center light and passenger side without blowing fuse driver side however does not work. Because I disconnected the brake light wire to driver side green wire. When I reconnected the driver side brake light wire fuse blew.
So I have it narrowed down to driver side brake light. here is my problem. I have checked all the wires that i can see for bad or frayed /worn naked places i have found none I can get to the wires beside gas tank running the rail to check but it is doubtful that it is spot as nothing is rubbing along there. Could it be a relay somewhere? can i just run a new wire from brake light? if so where to i connect to? Is there a wiring harness i can just buy and replace the brake light wires from brake light to power source I have ran out of things to check on my own...
I have a 2002 f350 7.3 PS that every time I touch the brake pedal it blows the #6 fuse(trailer tow brake/turn signal). I need to use my trailer.
View 14 RepliesWindshield wipers, and washer were suddenly not working the other day, so I discovered a blown fuse. Put a new one in, and it immediately blew again. So there is definitely something grounding out, and I am suspecting the wiper motor itself because so far I have not been able to find any wires shorting out, but before I go to the trouble of pulling the motor out and testing it, or replacing it.
Truck is a 2002 F350CC 7.3 TD. Wipers were working fine the other day before I pressure washed it, which is why I really suspect the wiper motor itself.
Every time I step on the brakes, there is a bright spark in fuse #13. My brake lights, turn signals and hazards don't work. At this point my truck isn't drivable.
According to the owner's manual in my truck, says circuit #13 is for "stop lamps, CHMSL/hazard, trailer tow stop lamp, and speed control."
I'm assuming that the hazard part covers the turn signals as well, but I know the cruise control works even when the fuse is blown. I used it last night on the way home (this was before I realized I didn't have brake lights).
So I know I have a short somewhere. The only mods I've done to the lights are aftermarket headlights, but if the fuse only gets blown when I step on the brakes, I don't see what that would have to do with it. Also, the lights have been installed and working for about a month before this started. The only thing that I did around the same time was install the gauges. I ran the power to them from #5, the customer access circuit.
Are there any other "common" areas for this to happen? I already removed the rear brake lights and it didn't work. I am quickly running out of 20A mini fuses.
My daughter came home a bit ago and told me the backup lights on my '02 F350 were on. Pretty odd because the keys were in my pocket at the time.
When I opened the door to the truck, I noticed a faint electrical smell and noticed the fan for the environmental controls was running as well.
I'm guessing the light issue is probably a sensor or something at the transmission but why would the blower be running as well?
Early last week I finally decided to try and figure out why my cruise control hadn't been working and discovered fuse F2.34 was blown. Replaced it and went through the test procedure described here: [URL] ....
No issues and the cruise is working again. I had to take it on a road trip for work the following day and didn't have any issues for almost 1,000 miles.
I drove it last night and didn't have the issue. I drove it again this morning to several places and everything was fine.
I've got a tuner with a code reader. Would something like the above problem register a code?
I've not stuck my head under the truck yet (it's cold and dark out.) What sensors I might need to check out? Is there a testing procedure available to ID the faulty component?
The battery is disconnected for the night, but I'd sure like to get this thing sorted before I hit the road for work again this week.
I am having a problem with trailer lights and an 03 350. When the truck is in reverse the fuse for travel trailer running lights and tail lights blows immediately. Changing plugs on the truck did not work. Truck has been hooked up to 4 other trailers including another travel trailer with no problems. Our travel trailer has been hooked up to an 08 and a 2011 truck with no problems. Fuse 38 20 amp. 7 post rv plug.
View 3 Replies2 things-
1) When it rains, I get water dripping in the cab over the glove box. The seal on the windshield looks fine. Truck has a sun roof. Is there a drain tube or something from there that might be plugged?
2) AC sometimes blows very humid air in the cab. It doesn't do it all the time, but seems to be in a cycle. After it runs for a while it switches to this humid mode and gets almost unbearable, to the point that I turn it off. In summer, when cooling, this air is warm. In winter, air is warm, but fogs windows pretty bad. What causes this? Noticed also that the tubes under the hood covered in frost and truck drips water from this area seemingly excessive when I park it.
The truck is an 05 F350 King Ranch 4x4 with the 6.0 Powerstroke
Installing a back up camera and need to locate reverse lights on driver's side at rear bumper. What color wire is for the reverse lights on a 2003 F-350 (truck in my sig)?
View 4 RepliesI have an 05 f350. I cannot get trailer running lights to work. All other lights work. Trailer brakes work, battery charge for dump trailer. I've checked fuses under dash and under hood. Everything checks out. I'm Stumped.
View 6 Replies2005 F350 Super Duty. I have no brake lights turn signals or hazards. dealer suggested the multiswitch but changed it and still not working?
View 2 RepliesMy problem had been intermittent for last few days. I have a Ford Crew Cab - 7.3 Powerstroke Diesel. The ford store told me it would cost hundreds of dollars to chase this short- to wait til it finally burns out then - bring truck to them.?
My fuse # 45 a 10 AMP fuse . Keeps blowing out. This fuse controls the gauges on dashboard and fuel peddle. I can start engine and if gauges come up like they should- I can place into driver - and give engine fuel from peddle- gauges down dead and no fuel go to motor. It just idles and still runs and will still move forward or backward. But only at idle speed.
I could replace blown fuse - #45 - 10 amp and it would a the first few times would go and work normally.
Now everytime I replace fuse it blows fuse - sometimes after putting 10 or more fuses in- one might work until I stop or put into park. Then fuse blows again??
Last night and today it took no less than 20 - 10amp fuses to get close to home and end up straight wiring with a small piece of electrical wire - severing as a jumper- it ran great - til I stop at mail box and got mail - saw slight smoke and pulled wire quickly out and idled down driveway to house..
Started my truck the other day no problems,minute into the start truck shuts right off like someone turned key. Checked fuses , #30 fuse under the column was blown, replaced it and tried to start truck. No luck fuse keeps popping. After changing again i was able to get truck started for a second and POP goes the fuse?
1999 F550 superduty 7.3....
1999 ford superduty keep blowing the 30 amp fuse under the dash, want let it start, why this is happening and the cause of it.
View 1 RepliesWhy I"am blowing #19 fuse it is a 10 amp fuse. It is in the passenger compartment fuse panel. It controls the auxiliary powertrain control module (diesel only),Instrument Cluster, GEM Module, Overdrive Cancel Switch, Idel Validation (Diesel only), Overhead Console and Diesel PCM via Clutch. I would like to know where to start looking to solve this problom.
View 12 RepliesI keep blowing the fuse to the headlights. When low beam is on, the right blinker flashes the low lights. When high beam is on, the blinker works. when I turn on the low lights, my cluster light indicators show the right blinker dim and the high beam indicator light is also dim.
View 1 RepliesMy truck keeps blowing fuse 28 in the inside fuse box. This fuse belongs to the ignition relay, and only blows when I go to start the truck. It is intermittent
View 14 RepliesI blew 2 fuses the other night, one in my power point and one in my lighter. I was using my ipod in the lighter and my beacon light outta the powerpoint. i changed them both (20 amp) and the lighter is fine but the power point keeps popping. What the problem might be? I would take it right to ford but unfortunately my warranty expired 9 days ago...
View 12 RepliesI have an 01 f250 5.4l standard. #19 fuse keeps blowing. I hAve taken the gauge cluster out and do not see any wires melted or burned. It blows the fuse as soon as I turn the key over. I have read things saying the overdrive but that doesn't work with mine.
View 4 Replies