Ford Super Duty (1999-2016) :: 2005 F250 Would Not Start / Engine Just Kept Rolling Over
Nov 13, 2013
I have a 2005 ford f250 super duty 5.4L the problem am having is the other day I took the truck out the yard an parked it across the street. 2 hours later I went back to move it it would not start the engine just kept rolling over I did this for about an hour it still refused to start. 2 days later I tried it again it started without any problems. I put a code reader on it it said P0453 fuel tank pressure sensor. If that is going bad would that cause that problem or would it be another cause.
View 2 Replies
Advertisement
My 2001 f250 on occasion will roll a very uncomfortable distance when I put it in park. Not all the time, but enough to concern me. It will roll a good 12-18" before the park rod or what have you engages. Doesn't seem to be affected by grade. Matter if fact it has always done it on just slight grades. Nothing like a boat ramp. It rolls enough that if someone had been front or back it would have bumped them.
View 1 Replies
So, when trying to start my vehicle it doesn't even turn over. Just clicks continuously. Both of my batteries are putting out 12 Volts. I tried the old arcing my solenoid with a screw driver while key is in on position and I got a couple of turns, but it wouldn't completely turnover. My solenoid has power going to it. Checked all fuses that could coincide with this issue. Not sure where to go from here. I have an 05 Ford F-250 XLT.
View 7 Replies
Got off the freeway today, driving along about 40 or so thought I smelled something hot like something burning. Stopped in a parking lot and smoke was rolling out from drivers side rear wheel. Look under and oil is dripping from inside of the wheel. Figure the caliper was hung up and got so hot it took the seal out. I can't get to it right now and the shop says I can't get in until next week, need my truck now. How long could I get by the way it is IF I take it real easy.
View 9 Replies
I have a 05 f250 6.0 that currently will not start and no smoke. Replaced batteries and tested ficm. At initial injector buzz voltage drops to 18.8 then jumps back to 48.8 and drops again to 18.8 while cranking. My question is if the voltage is this low does the pcb still just need a resolder or are there components that will need to be replaced?
View 1 Replies
I have a 2005 F250 with a5.4 engine. When the engine is cold runs fine. When engine gets hot the vehicle shuts down.
View 1 Replies
I have a 2005 F250 with the 5.4. This truck has been one thing after another, as you can tell from my other posts. The problem this time is, if it cranks hard to start because it's cold(can be anywhere from as high as 32, but usually in the teens) it will start just fine, then several minutes later throw the check engine light. Put the scanner on, like clockwork, 4 codes, always cylinder 1 misfire pending, misfire on first 1,000 revolutions pending, cylinder 1 misfire confirmed, misfire on first 1,000 revolutions confirmed.
Sometimes you can hear a slight lope in the idle when it does this. Clear the codes, runs perfectly fine. It will never do it after it's been started for the day. Some days you would think for sure it would throw it when it's frigid and the winds been blowing on it, it doesn't bother, other days you wouldn't think it would, and it does.Can the computer think that since it didn't start right up, it misfired?
View 9 Replies
Pulled into parking lot this morning, 05 F250 CC 4x4 V10, truck starts dinging at me, Park brake light comes on. Ease off of gas and idle around to parking place, no sign of brake drag. Release Park brake, no difference, set the brake and release, no difference, guess the microswitch went bad. Not raining, never hit a bump, MAY have had my foot on the brake, but that shouldn't effect the P Brake.
After setting for the 12 hour shift, all is good and well. Did not come back on.
Where this switch is? Is it under the cover by the foot set or under the truck along the cable? Would like to know where to look next time this comes up. Did have 2 new tires installed on the front a week ago, new tierod and aligned at the same time.
Just wondering and curious, my last F150 had all kinds of electrical germlins in the windshield wiper arm.
View 8 Replies
I have a 05 f250 with a 5.4 I'm having issues with I was driving along the truck started chugging along and the check engine light came on so I checked it with my bully dog the codes that came up were p0192 which is fuel pressure sensor circuit low the next one is p0452 is evaporative emission pressure sensor switch low also came up with p0191 tonight haven't dug into that yet.
I change out the pressure sensor switch from a buddies truck didn't make a difference put my sensor in his truck his worked fine I clean the throttle position sensor and The maf also put a new air filter on not throwing a misfire code but seems like it may be. A little background on the truck it's a 5.4 3valve with a bully dog tuner, mufflers been removed added straight pipe mechanically that's all that's done
View 4 Replies
You know the "mechanic's fiances truck" problem. I recently replaced the cam sensor in my 05' F250 Gas. The check engine light had been on for a while before that and my truck rode great, however I now want to sell it and I can't do that with a check engine light on. It's got about 85k miles on it.
After replacing the sensor, the light went off for about 20 miles, but it is now back on and my truck seems to miss every once in a while on acceleration or cruising. Some days it's worse than others. The check engine light still says cam sensor, but the sensor is brand new.
My fiance is a mechanic, so I don't know all the details about code numbers and such. However, I want to sell this truck pretty soon, and I would like it to run correctly. His dad (another mechanic) seems to think it could be a coil and wants to wait for that light to come on, but I would rather fix the problem and sell the truck!
View 1 Replies
I have 05 F250 SD with 150k on it. The engine has the typical cam phaser knock, timing chain slap on start up and occasionally have a noisy lifter. As long as I use fresh 20-40 oil the engine symptoms are less and the engine runs strong. The motor also doesn't leak or burn oil and the plugs were change out about 20k ago.
The truck is still good and is prefect for my needs so to me it's seems worth fixing the needed repairs. What I would like to figure out how far should I take the motor... just have the chains, guides and phasers replaced or buy a rebuilt motor and swap it? I'm thinking just doing the phases and etc would be 1/2 the cost but may not last as long as rebuilt motor. But realistically I might only put 5-7k miles are year on it anyways.
View 14 Replies
I have an 2005 F250 4.2tdi XLT. There is a buzzing sound coming from somewhere near the fuel filter area in the engine bay. This started after changing the fuel filter during a service. Its also difficult to start now. It has to swing for 10 secs before the engine fires. What it could be?
View 4 Replies
My dads 05 f250 6.0 PSD. He says he'll take off in the morning and the fuel gauge will randomly drop to empty and trigger the low fuel light, but then also the Check Engine Light will come on. My brother did a code scan and no codes come up. Where we should be looking to remedy this one?
View 14 Replies
I replaced the head gaskets on a 2006 F250 6.0 Diesel, put it all back together and started it up. It ran great for a lil bit, then it started cutting out. It did this for about an hour then I killed it and it took a little bit to restart it, spinning over and over to get it to run, this took place several times. The engine died and now it will not start. I keep getting codes P2284 and P2290. What could be causing this problem??
View 9 Replies
2005 F250 6.0L ... My truck is running really rough when the engine isn't all the way quite warmed up. once the truck is fully warmed up to normal running temp it runs good. I am getting four engine codes. P0672, P0673, P0674, P0676 These codes say 2,3,4, and 6 glow plugs have a open circuit. Can this be the cause of my problem?
View 7 Replies
Just this morning I tried to remote start my '13 F250 6.7 and all i got was the doors lock and a two honks. The two honks are usually when there is a door left open when you click the lock button two times but all of my doors were locked. After I started the truck with the key and took it out to go run a errand I noticed the check engine light turned on. Could this be connected or just a coincidence?
View 4 Replies
I see several threads regarding engines that wont start for no apparent reason. My reason was a failed fuel pump relay. This sucker is hidden in the dash below and to the left of the radio. I got to it by taking out the ash tray. There are three relays under the cover. The upper left is the fuel pump relay. The one to the right is the turn signal relay. I don't know what the bottom left is for.
View 3 Replies
2005 f350 crewcab 6.0 sprayed engine down with degreaser and hosed off 4 days ago wont start have dried and blown everything out still nothing....
View 3 Replies
2005 F-250 King Ranch Diesel ... My truck when I got it the 4x4 wouldn't engage. I replace the front inner seals, and the lock outs. Still wouldn't work. Took the shift motor off and freed it up and it worked fin till today. Changed the shift motor and still nothing. This truck has been nothing but problems since I have had it and now this ... Truck is going on the market soon and would sell better if the 4x4 worked ...
View 13 Replies
F-250 2005 XLT 5.4L 4X4. Had ford for a few years now (Escape as a personal vehicle and econoline as business vehicle). Now I'm having a little problem with 4x4. It wont engage. Worked fine last week and now nothing! I did check all the fuses and when i switch to either 4Lo or 4Hi I can hear a clicking sound behind the switch but feel like it's getting blocked or something. Tries a few time then stop...
View 14 Replies
I have had the ABS light on for about a year now. I looked thru the forums and found that the typical reason if a faulty rear VSS (vehicle speed sensor). I found a replacement part online and got it ordered and replaced the original part. Simple 5 minute fix, but it didn't fix it!
Now when I get in and start the truck the ABS light is off, but after I drive off about 20 yards the light comes back on and stays on.
The other day someone stepped out in front of me at a cross walk and I hit the brakes pretty hard and although the truck stopped in time, the rear wheels locked up, so I'm thinking the issue is at the rear.
View 5 Replies
