Ford Super Duty (1999-2016) :: 2005 F250 - Error Codes P0299 And P2263
Apr 19, 2016
I just got my 2005 F250 diesel out of the shop. The errors codes P0299 and P2263 were listed on the computer. The service done, was to clean carbon from turobo charger and service the EGR valve. I talked with the mechanic and he recommended that I use Cetane Booster Additive. What would the Cetane Booster do? How would it prevent the carbon build-up in the turbocharger? What should I do to prevent turbocharger carbon build-up?
View 3 Replies
Advertisement
05 5.4 F250 4x4. Keep getting those codes. Can't find any vacuum leaks. swapped rear O2 sensors. Fuel filter twice in last 11k miles last time was 1k ago. Will the 430 code cause the lean codes from a bad cat? I've been getting the 430 code for at least 4 mo's.
View 6 Replies
My 2005 f250 5.4 with codes p0171 and p0174. I have replaced fuel filter, MAF, Checked for vac leaks by smoke and water test.
I don't have a way to check fuel pressure on this thing since it must have been to much trouble to put that test port on the fuel rail!!!
View 10 Replies
My '05 F250 (5.4) started misfiring and threw codes for p0300, p0305, p0307, p0308,and p2198. I used an inline spark checker to check cops, which all had spark. Replaced 5, 6, 7, and 8 plugs and cleared codes. Ran truck for a few minutes and codes came back. Switched #5 and #6 cops and cleared codes. 5,7,and 8 cylinders still misfiring (same codes). Truck only has 36,000 miles and spent alot of time just sitting. Plugs were original plugs.
Replaced 5-8 with Autolite OEM replacements. I haven't checked cops for resistance yet. Weather was pretty cold when problem started. Threw in about 10oz. of Lucas to no avail. I had this problem last winter with the same cylinders throwing codes. Threw some Lucas in the tank and idled truck for approx. 1/2 hour and problem went away except for stumbling most every time truck came to a stop. I'm starting to wonder if it's a coil or a fuel issue.
View 10 Replies
After finding that a battery was low and not getting charge, they found the alternator was bad. Replaced that. Next the battery that was low was able to be charged and did not effect the other battery. Both batteries have been load and charge tested and they both read 84% charged. I am told this is "good."
Next I swapped both fuel filters and did the oil change as well. I finally got a chance to get my friend to run his scanner on it. The results are injectors and FICM. The codes are PO261, 264, 267, 270, 273, 276, 279, 282, and finally 611. I guess this means that the FICM is toast.
I have tried salvage and no one has anything. I guess I still don't understand how this truck is capable of running daily with the computer throwing every code dealing with the injectors and the computer that runs them.
View 14 Replies
2005 F250 6.0L ... My truck is running really rough when the engine isn't all the way quite warmed up. once the truck is fully warmed up to normal running temp it runs good. I am getting four engine codes. P0672, P0673, P0674, P0676 These codes say 2,3,4, and 6 glow plugs have a open circuit. Can this be the cause of my problem?
View 7 Replies
Engine light and error code for tps occasionally comes on , then stays off a while. parts store said it was ok (shows full range) , but ford has an update for computer to fix. engine is v10 and parts store erased code and it hasnt come back. the only indication that something was wrong is the light coming on and once on the interstate at high speed , then the off ramp slow down, the engine seemed to want to stall as if engine not matching actual speed for a few seconds, then it was ok again. I was out of town and the mechanic that looked at it told me to go to Ford for an update. He tested the tps and said it was ok.
View 2 Replies
99 F250 Super Duty 5.4 has a p7147 error. Traced all wiring cant find any short. Bought reman solenoid pack # are f81p-7g391-cb with green cover my old one in trans is f81p-7g391-ba with blue cover. Are these interchangeable? Have tried to read up on pwm & nonpwm and getting confused.
View 2 Replies
2006 F-250 6.0... I'm getting a P0470 error code and no boost, The unison ring is free and clear, the Turbo will not create boost till about 2000 RPM on the road. If I unplug the VGT there is no change in the turbo.
When the vehicle is started there is no tone change in the exhaust. This just started after I replaced a dummy plug in the oil rail. I checked all the connectors as well. I cleaned the EBP and tube.
View 1 Replies
My truck is back in the shop for a third time for the same problem and the dealer is really clueless about anything. Here are the alarms I get when trying to start( Low Oil Pressure, Service AdvanceTrac, Engine Overtemp, Wrench Icon and Starting System Fault.)
When trying remote start nothing happens then the horns honks after a couple of minutes.
Below is the timeline and a video.
July 21, 2015 - Vehicle would not start, multiple alarms going off and dashboard has all icons showing. Towed vehicle in around 0700. Truck stayed in the shop overnight. Resolutions was told that the codes was reset and battery cable was tighten. I ask why the battery was loose when it was just in the shop for routine maintenance and it was signed off that it was good to go. I also told the service representative that I felt this didn't not solve my problem as it was just a quick fix.
Sept 4, 2015 - Problem is back, same symptoms, truck not starting, alarms going off, dashboard has all icons showing. Towed vehicle in around 1700. Vehicle stay in the shop for a week and was picked up around 1800 on Sept 11, 2015. Service representative stated they replaced the PCM and reprogrammed the keys.
Sept 12, 2015 - Yep you guess it, same problem and not even a full 24 hours from when the vehicle was towed to the dealership again. Truck wont start, same symptoms, alarms going off, all icons showing. Towed vehicle in around 0900. Vehicle would start now but check engine light is on. I have an inclination that all that will be done is to reset the codes.
2014 F250 6.7 Starting issues - YouTube
View 14 Replies
2005 V-10... I've found some info on the "fuel level data error" but thought there must be more on this. In the last month or so I get the error on the message center and the fuel gauge goes to E. Happened a couple times here and there and then the CEL has come on. Have nto been able to get the CEL to go out because it happens too often now.
Have tried a couple bottles of Techron because that is suppose to fix it but no luck after about 150 miles. Can't find any loose wires/connectors. Am ready to give up and drop the tank. Is the sensor separate or part of the pump assy? Also don't see alot on dropping the tank on SDs. Any tips?
View 14 Replies
I've got an intermittent Trailer Wiring Error message that started appearing with a trailer connected on my '11 F250.
Brakes and lights work OK on the trailer, I thought I had read on the board here that there was a TSB for this, but I cannot find it.
View 10 Replies
Where to start. Have had to replace a few COP's in the past and replaced all spark plugs 20k ago. Truck runs rough at idle and sometimes stalls when changing gear. Strong exhaust smell when sitting idle. If I put my foot in it there is hesitation. Engine seems to smooth out quite a bit but also seems like it's getting more power in stages. Codes P0426 and P0345 ....
View 2 Replies
Ok so my F250 died last night. I read the Pcodes and came up with P2198 and P0506. I am pretty good with fixing the truck but need to know exactly what is wrong.
View 5 Replies
The engine was just rebuilt, 7.3L diesel. New bottom end, cam and turbo also new harness for valve covers and injectors, new #8 injector(#8 cylinder lost compression). The engine cranks and idles great. Run it up to 1800rpm - 2200rpm and you get a miss or skip. Almost like the engine turns off and back on very quick, and it makes a clank noise. No codes, reading it with a OTC Genisys 4.0. I also swapped the PCM and IDM with another truck and it still does same thing. Other truck runs fine. Year model 2000 w/ 230,000 miles
View 1 Replies
Long time follower, first time user. 99 F250 V10 180,000 miles: About a month ago I replaced both upstream oxygen sensors. I know have the following codes:
0135 and 0155 for Upstream Heated Oxygen Sensor Heater HTR 21 and 11
Circuit Malfunction Bank 1 and 2
1409 for Exhaust Gas Recirculation Vacuum Regulator Solenoid Circuit
I checked fuses and PCM relay and all are good. I have 12 volts to both oxygen sensors and no noticeable wire burns. One of the possible causes given on code printout for 0135/0155 is to check for a disconnected hose to the EGR. All hoses are good. One of the possible reported fixes for EGR code 1409 is to repair oxygen sensor wiring. So my question is: Are these codes related. If I replace the EGR vacuum regulator solenoid, will this clear my codes from the oxygen sensors?
View 2 Replies
I have an intermittent problem with my 09 F250 Diesel. A few times now under hard acceleration I have had the trans seemingly get stuck in 3rd gear. The little service required wrench symbol showed up on info screen but after shutting off the engine no codes were present. A week or 2 later this happened again and I ran diagnostics through my Spartan tuner and got P0771 and P2704 for codes.
Again they cleared when I shut the engine off. Since this is an intermittent problem, only after hard acceleration, would it make sense to change tranny fluid, maybe do a tranny flush? Or am I off to the dealership for a rebuild?
2009 F250 Lariat Crew Cab Short Box
Spartan DashDaq
S&B Cold Air Intake
4" Flange-back w/6" Can
Package by Dirty Diesel Customs-Red Deer Alberta
View 5 Replies
Trying to perform master reset on sync because, from the title, phone button inoperative, No Aux In, and attempting to connect the ipod, you get "connection error see dealer".
The Owner's manual indicates Fuse 40 protects Sync, GPS and Sirius, so I figure that is the one. When you pull 40 you still have gps and Sirius, so I figure Sync must still have power also. So, what fuse powers the sync module?
View 1 Replies
2005 F350 crew cab with 6.0 currently cranks but no start with a P2291 error code. Using scanguage 2 it shows icp 0, IPR 67.7, FICM 47.5 while cranking. Disconnected ICP and still no start. removed icp and hooked up air and I do not hear/see any signs of air leaking. When I disconnect the air it then whooshes out. About 2 months ago got a #1 cylinder contribution error code and changed out that injector and it has ran fine up until this issue.
Can this be a IPR? I am leading towards the HPOP, but as it costs a pretty penny would really love to make sure I tried every other avenue.
I have 197K on it, and 2 years ago did a EGR cooler delete. In May this year replaced the oil cooler, and then in August changed out the #1 fuel injector.
Oil cooler screen was broken. Cleaned the entire reservoir out. Could this just be a clogged IPR? or seeing the change while cranking an indication that it is working?
View 1 Replies
I have a 2008 f250 superduty with the v10. Just today I was driving and engine picked up.slight miss it's rainy. I thought coil pack, but it left me on side of road. Got fired limped home won't go more than 40mph. Runs rough, no power, checked codes and get P0340, p0357, p1336, and P2195.. Where to start.. My daily driver and have to get back on road.
View 1 Replies
I recently bought a 2008 F250 with the 6.4 diesel indirectly from a dealership. The truck itself has 220,000ish kilometers, but the engine (as well as the turbos) are Ford reman that had about 12,000km when I bought it and I have only put about 6500km on it. It is already leaking oil but that is for another thread.
The reverse sensors, steering wheel controls and part of the stock 6cd radio have never worked. The towing system has errors as well. The fuel level sensor often has problems reading the new level after I put in fuel, but that is always fixed by disconnecting the batteries and forcing a hard reset.
I figured the steering wheel/cruise control problem was due to either a broken clock spring and/or the brake pressure switch. I replaced both those as well as the airbag because the horn relay failed closed when I put it back in the wheel. It did not fix the problem. The steering wheel buttons still intermittently illuminate, but the radio controls and cruise control buttons do not function regardless. The truck isn't giving any codes either.
The towing system will activate lights and brakes on a trailer as well as set the gain, but it will not detect that it is actually hooked to a trailer. I cleaned the pins, but I haven't looked any further into it. No codes for this as well.
The reverse sensors/system does not work. It will lock itself in "off". I am guessing this is because one or more of the sensors have failed, but I am skeptical that it would be just that given the trucks other problems.
The radio does work, but the auxiliary input/mode will not work. I ran the diagnostics on the radio and on 'Test 1' I got "SELF FAIL B1342 ECU" and "B2477 CONFIG". I tried to clear the codes, but I can't. I think this means the radio is kill.
View 6 Replies
