Ford Super Duty (1999-2016) :: 2004 - Transmission Line From Bottom Radiator Leaking?
Jul 5, 2014
So this is my major problem, leaving for a camping trip tomorrow afternoon. It's just 15 miles away, easy flat drive. What has happened is the trans line coming out of the bottom of radiator is leaking next to the fitting about an 1/8 ' out, So I can't cut off and splice in hose for the trip. I worked on it for about an hour, rusted on, tried some heat and now have some PB Blast on it and all I am doing is starting to round off the head of fitting. Is there any way to bypass this just to get the camper to campground and then get to a shop while we are gone Don't care if I have to splice and cut, will get new lines later.
2004 f250SD 5.4 83000miles
View 3 Replies
Advertisement
My transmission cooling line is leaking. It leaks where it connects to the radiator. Im not sure how I go about removing the connection from the radiator. It is tough to tell from the rust on the connection weather or not I can use a wrench on it. I have read here that there are cooling lines in this part of the radiator for the transmission. Is it serviceable or do I need a new radiator. I dont want to touch it until I know what I'm looking at.
05 F250 5.4L 4x4
[URL]......
View 13 Replies
So my 2000 f350 is leaking transmission fluid from the cooler line. It goes to the rear of the transmission, but where does it go to from there?
View 5 Replies
I have heard that the front brakes are separate, and if the rear brakes have a leak and the line is empty, the fronts should still work. Is this likely to be true? If I drive the truck will I be able to stop with the fronts alone (assuming they will still work?)
I plan to drop the truck off late tonight when there is likely to be no traffic, but thought I would ask.
View 14 Replies
This is something to check, I found the vent line pinched closed on my 2000 F350 when I was trying to find out why it was leaking. When I was under my 2013 installing the hitch I checked it and found the same problem. The clip doesn't pinch it closed right away but it will happen if you don't move the clip.
View 8 Replies
I replaced a rear rusted brake line a couple of years ago. It rusted where the line met the bracket. I'd never done this before but bought a flare (flaring?) tool and fixed it.
This week the longer line that runs down the length of the truck started leaking. It looks like the line was once held in place by a small bracket just in front of the rear wheel but it wasn't in that bracket anymore. I guess it rubbed against the metal and water/sand rusted it out.
A local garage said they'd need to drop the fuel tank and estimated that it would be several hours (and hundreds of dollars) to do the job. It looks like I might be able to cut the old one out and then fish the new line up through there and replace it.
Also, what is the diameter of the line? It is a 2004 F350. I can certainly cut it out first and then take a piece of it to the local auto parts place to get the replacement line.
View 9 Replies
OK, so I ordered in the new lines and have them. BUT my problem is snaking the factory transmission line out from under the truck. I have pictures to show my struggles.
How do I pull this:
Out of here???
Towards the front of the motor
Front passenger side cab corner
Replacing these lines? I don't care about breaking the old one, but I still need to find a way to install the new one.
View 11 Replies
I have replaced both the transmission lines except the one that connects the two. It is the one near the top of the transmission that is about a foot long and goes from the fitting of the one transmission line to the other fitting for the other line. My questions is how do I remove it? It seems to be permanently affixed to the fittings, so those it come attached to new fittings?
View 2 Replies
I have a 2000 f250 V10 CC 4x4 long bed. The rubber fuel line that has a quick disconnect to attach to the fuel filter along frame is leaking. This is on the filter side going to engine. Ford tells me fuel line not available. Dorman products tech assist can't tell me which connector of there's will fit my truck.
View 2 Replies
I'm having trouble disconnecting the transmission lines to replace them. I can't get them off. I have the tool. Can I replace the fittings in the radiator?.
View 3 Replies
I have a 2008 Ford F250 V-10 Superduty and recently I had a transmission cooler line start to leak. I ordered replacement lines and the tool for the quick disconnect. The line that's leaking is from the radiator to the quick disconnect. I was able to replace the one line, however the second line (problem area) has been a nightmare. The line cracked right at the quick disconnect fitting.
The hard line is tight in the fitting and corroded. broke the tool trying to remove from disconnect. The line is flush with the quick disconnect. How to get that out of the fitting? or another method of fix? Its a hard 1/2 line going into connect crimped to rubber line going to transmission.
View 13 Replies
I am not positive where it could be but I have a good bit of oil on the transmission (i think) i was trying to replace the strarter and noticed it. Where the possible leak could be from? No oil on the ground under the truck.
View 3 Replies
Have a 2007 V10 and I want to put in a Magnafine tranny filter. Instructions say to plumb it in to the return line. Which one is this, top or bottom?
View 11 Replies
Need to know if the brake line fittings are SAE or metric? Mine blew a leak on the line that runs behind the gas tank on the drivers side frame. It's a 2004 5.4l f 350 4 x 4, 4 wheel disc brakes...
View 4 Replies
So I had an issue with the trans temp sender leaking out of the test port where it's installed. My first clue was a smell of ATF, then a high trans temp, and finally many, many spots on the driveway. Anyway, I discovered that either I lost the o-ring for the sender or it didn't come with one. Regardless, I got an o-ring and its sealed for the most part. There is still a drop or two under the truck after it has been running. How can I fully get rid of this issue? Would some RTV thread sealer do the trick?
View 3 Replies
New to me truck has 80k on it, it's leaking at the bell housing. Pulled the inspection plate and it's definitely red stinky automatic transmission fluid. Back of the torque converter is clean.
Ford warranty has run out, however I do have an aftermarket warranty on the truck. Trans temp isn't above normal or running hot.
I'm a very mechanically inclined engineer, I do not work on cars for a living, but I have replaced an input shaft seal on a 4wd transmission before. That's my best guess as to what's leaking. Is this a common issue?
View 3 Replies
I just changed transfer case fluid on my father's F-350 for the first time in 13 years. (over 230k). Removed fill plug first and fluid gushed out of the fill hole unexpectedly. Did not have catch pan ready, so made a mess. I thought it was just over filled form the factory, but too much was coming out to be simple overfill. Almost 2 qt came out of the fill plug.
Did some google search and found many Ford trucks have failed transmission output shaft seal and transmission fluid leaks out to transfer case, causing transfer case to overfill. I am yet to check transmission fluid level, but considering how much came out of it that probably is the case.
Now, how bad of the problem this really is? Will overfilled transfer case cause some serious problem? 4x4 is rarely used (once or twice a year in winter) on this truck and from what I understand transfer case doesn't really do anything in 2WD other than just passing output from transmission through.
There are no fluid leaking outside and repairing the seal would be a too much of work for me.
Also changed rear differential fluid for the first time and I was surprised how clean the fluid was. There were thin layer of black sticky residue (sludge?) covering everything, but the fluid itself looked clean and no visible metal shavings. I guess that is why Ford said it does not require change under normal condition.
View 10 Replies
I have a 2004 Ford F-250 6.0 power stroke, the previous owner got water in the tank, rusted the injectors, and destroyed the pump, I changed the pump and 2 injectors, it still died. It has 300K miles on, pretty high. Right now all symptom is the motor is starving for fuel, because the injectors are leaking, getting air in it. When I pull the fuel filter out, it is full of dirt, And swollen up because of water. So, I am planning to flush the tank, get rid of the water and then replace the injectors. Could there be any damage on the motor ? Engine problems? I know 6.0 is a bad design, but apart from getting rid of it, how could I fix ?
View 3 Replies
How do you remove the transmission lines from the radiator. I have to replace the radiator and don't want to mess up the lines.
View 1 Replies
What is the part # for this bottom for an 05' F250 supercab?
I swapped these seats into my OBS truck, but the driver's seat bottom has the typical wear/tear on it and its getting worse.
I have been searching for three days for a replacement bottom cover. I have found them for F150s and the pattern is close but not right. I cannot find them for F250s or F350s as I cannot find the proper part # for the gray DS cover.
This is the tan one: 4c3z-2562900-eaa
How can I pull this up?
View 8 Replies
What this could be? It blinks all the time was on the truck when I got it. Has a button in the bottom of it. This is on a 2009 super duty 250 and the 6.4 L if that matters.
View 3 Replies