Ford Super Duty (1999-2016) :: 2004 - Small Piece Missing From F250 Frame?
Sep 6, 2014
I was washing my 2004 F-250 today and I looked down by the front passenger wheel well and I noticed a small chuck missing from the bottom of the frame. The other side in the same spot doesn't have it and at the spot in question, I noticed some sort of crack had been welded before. I never had any of that done to the truck. What about getting it fixed? get it fixed right away or keep an eye out for cracks. so far its just that hole and what looks like a welded crack above. everything else seems fine. I know a repair would be inexpensive and easy just to weld a steel or titanium plate on the spot.
View 11 Replies
Advertisement
Bought a dealer demo last may. Truck has been wonderful. Had less the 1500 miles on it. Noticed when I was installing the lock on my tailgate that some of the plugs that cover up the holes in the plastic piece inside the tailgate were missing. Maybe some of the screws, not sure. Dunno if it's supposed to be that way or what. Just started to get a horrible feeling about it, Taft maybe something major happened. Any way to find out or round they have told me? Mebbe I'm over thinking this.
View 6 Replies
I have a 2004 F-250 with a 6.0 and a 6-speed with 140,000 miles. It has been studded, and has upgraded injectors. ( Not sure on the size, they bored them at at the diesel shop that studded my heads.) Also have an EGR delete, with the EGR turned off on the SCT as well. I also have a SCT Livewire set on the 65HP tow tune.
Truck has always ran great in the year and a half I have had it. I changed the oil three days ago, and now I am getting a miss at idle. The trucks cranks right up and drives normally. Once it is at operating temperature, when I stop at a light it has a very noticeable miss. There is no surging, or change in RPM's at all. Just seems like it is cutting out every few seconds. This is also somewhat intermittent. FICM shows 49 volts always, even when this is occurring.
Also, this may be unrelated, my oil temperature seems higher since the oil change. Was around 192 water/197 oil while cruising 70 on the interstate. Now, its' more like 192/202. I've always ran Motorcraft 15w-40, and that is what I used for this oil change as well.
I see some people have a similar problem, but all the posts I've read involved fluctuating RPM's or surging, or both. Other than this, the truck cranks and runs just like normal.
View 2 Replies
I have recently purchased an 04 F250 crew cab with the 6.0 power stroke, it has a cold air intake, 4inch exhaust from the turbo back and has a program in it but programmer didn't come with the truck. When I sit at a traffic light and go to leave on a green light the truck kind of hesitates or acts like it's missing out( maybe loading up) shoots out black smoke then runs fine, it doesn't do it at all the stop lights but does get irritating. If I get it flashed back to stock settings will the truck run normal with all the upgrades?
View 4 Replies
My v10 has a cold miss when i start it in the morning no matter what the temp. It misses until it gets up to operating temp.then it runs fine all day with a slight miss.
- Changed plugs,
- Changed pcv,
- Changed iacv,
- Cleaned map sensor,
- Changed tube to pcv,
No codes. Its running as if it had a carb and the choke is closed. No smoke, tach. idles between 750 down to about 500, until it warms up then tach. Stays steady.
View 4 Replies
I have a 2000 f250 V10 CC 4x4 long bed. The rubber fuel line that has a quick disconnect to attach to the fuel filter along frame is leaking. This is on the filter side going to engine. Ford tells me fuel line not available. Dorman products tech assist can't tell me which connector of there's will fit my truck.
View 2 Replies
On the F250 trucks, if I changed the mounting frame under the seat, will the passenger side seat fit on the drivers side? Basically, can I turn a passenger seat into a drivers seat?
View 4 Replies
I have a 1999 ford f250 with a 6.8 liter v 10 engine. At about 40mph the truck will start missing and lacks power to accelerate further. This problem is intermittent. Some days it runs great and others the miss appears. Well I scanned and the code reader said that I had a misfire on cylinder 7. I took a chance and replaced the COP and the boot for that cylinder . Ran great for a day and then the miss came back. Same code again. What else might cause this? Are plugs difficult to change in these engines?
View 6 Replies
Just got a 2008 F-250, truck has the center console jump seat and the console lid is missing. Can you just buy a new lid or do you have to buy the whole thing? Cost? Places to buy?
View 4 Replies
Need the fuel system diagram or schematic for my truck.
1999 250 superduty v-10 Ser# 1FTNF20S1XEC67940
Every time I run it I smell gas. I changed the f/p 6mo ago. While I was working on it I noticed there was a hole rubbed in a small hose. I assumed it was a return line (smelled gas before too) and when I fixed it the smell went away until lately. I dropped the tank,yesterday and didn't see any problems. Just need to find out what hoses go where so I can replace the hoses??
View 7 Replies
I have 2005 f250 5.4l 3v that was having miss problems between 1200 and 2000 RPMs. Changed VCT solenoids which worked, but then could hear chain hitting cover when powering down throttle on left side. Figured chain tensioner was bad, so tore down and removed timing cover. Found left chain was tighter than what seems normal, and right side had huge amount of slack. While taking off tensioner on left side, something happened to fast for me to see it, and still not sure if what happened wasn't just my imagination. I thought that the chain moved very fast for an inch or two. Anyways, I watched how to video on timing the 3v, but I am very confused about it. The left bank seems to line up on timing marks perfectly, but the right chain is off by at least 2 1/2 links. Not knowing any better, I removed three rockers on left bank (2 intakes and 1 exhaust) but only removed two intake rockers on right side. I don't know what I am doing and getting scared.
View 1 Replies
I bought a 99 f250 super duty with v-10. Ran great then I decided to hose off engine compartment. No pressure washer just running water trying to get all the dirt off now the engine sounds like its missing. Could I have a coil pack that got wet or is something else wrong.
View 3 Replies
I have been reading several past post regarding the misfire while in OD and going up a small hill with light acceleration around 45 to 55 mph. Everything points to the COP so I replaced it today. Still getting the code after 20 minutes of driving around. My truck shudders and looses power. I can either let up on the throttle or hammer down on it to eventually smooth it out and everything goes back to normal.
Check engine light flashed but didn't stay on. My scanner does report misfire on cylinder 7 (P0307). Haven't owned this truck very long so I don't know much of it's history except OASIS report shows nothing alarming. Guess next step is a new set of plugs.
Another first today, is the tachometer is stuck at 4500 rpm. Shut the truck off and let it sit for an hour, then went back to start and tach. acts like 4500 is the new zero and running engine at 1000 rpm now indicates 5500. 2007 F250 SD 5.4 ....
View 14 Replies
The truck has 64k miles and has developed a small leak on the engine side of the radiator with no apparent damage. There is no variation on the pressure test and the dealer was able to find the very small leak with dye in the system. It has lowered by about 3/4 of a gallon of coolant over the last couple of months. There are no visible signs of a leak but you smell the coolant when you stop the truck.
View 11 Replies
So, I have a 2007 f250 with the 6.0. When she's cold she starts fine but runs rough like she has a miss. When she warms up the miss goes away and it runs pretty good. But if I shut it off it won't start for about an hour or so.
ICP sensor has been replaced.
FICM is putting out 50v
View 11 Replies
I have a 2008 f250 superduty with the v10. Just today I was driving and engine picked up.slight miss it's rainy. I thought coil pack, but it left me on side of road. Got fired limped home won't go more than 40mph. Runs rough, no power, checked codes and get P0340, p0357, p1336, and P2195.. Where to start.. My daily driver and have to get back on road.
View 1 Replies
I have a 2007 F250 4X4 6.0 diesel. When first started it idles extremely rough to a point it sounds like a old gas engine missing. But after it warms up for about 15 minutes it runs and idles like a new truck. I'm thinking it's the injectors if so is this something I can change/clean ....
View 2 Replies
I've got a 2008 f-250 extra cab. A small bump will cause the rear driver side door to pop open. What I have to do to fix it, I don't want the grandkids falling out.
View 2 Replies
I've got a 2006 F250 5.4l Super Cab. When I bought the truck the rear interior door trim panels were missing. I tried to order them straight from ford but it turns out they no longer carry them, and I can't seem to find them anywhere online. I've also looked at the salvage yards in my area- nothing. Where I would be able to find these elusive creatures?
View 3 Replies
My truck is a 2003 f250 / 2wd automatic, 7.3 powerstroke, 284000 well maintained miles.
Just last week I sprug a large oil leak and had to replace the hoop outlet o rings..problem solved. This week I can drive 15-20 miles on the freeway and the truck starts to act like ota running out of fuel. Bogs down to 40mph then starts missing. I pull over, and when revving I have un burnt fuel and oil smoking out of my tailpipe. I let it sit for 5-10 minutes and it will be fine for the rest of the drive and this happens intermittently, there is no pattern.
The truck has a ton of power, starts great hot or cold. I did a ton of research and found a IPR could possibly cause this, as could plugged screens in the fuel pickup. Then I read about all the injector harness issues but I don't think that I my issue.
View 8 Replies
2002 F-250 7.3 4x4 ...
I have a rattling noise coming from the front suspension (both sides) when going over small bumps. Most people point to ball joints, but I find my case odd because I just replaced
Upper/Lower ball joints
Track bar
Tie rod ends
Shocks
Front U joints
Drag link
I did not touch the leaf springs or the sway bar, except to grease the links, which otherwise looked good.
View 3 Replies
