I have a 04 f350 6.0L truck ran great all day today then out of the blue it started shacking and lost power then i plugged my tunner in and code popped up po284.
View 6 RepliesSo I was traveling thru the grapevine on the 5 Fwy and no problems. Made it to the top didn't over heat. Then all of a sudden it lost power. Pulled over and it stopped running. Won't start. Fuel is pumping, I took off the fuel filter and turned ignition on and it filled up.
View 2 RepliesSo I have a 1999 F350 diesel and the fuse panel under the steering wheel is acting up. I was driving my truck home the other night and I lost power and my truck shut off. I have had a problem in the past with the #30- 30 amp fuse ( controls the PCM and glow plugs from my understanding) that is under the steering wheel, I replaced the fuse and everything started working normally again.
Until the other night when my truck shut off, so I replaced the fuse the truck drove again for 20 feet died again, I was able to hold the #30 fuse and allow my truck to start up again but would eventually killed the PCM and shut off again and would not start up due to what I believe the fuse location shorting it out and killing the power to the PCM preventing me from starting it up again. I had my truck towed home and charged the battery and it started up fine the next morning. If I push on the #30 fuse my truck the shorts out and kills the power, I do not know if this is normal?
The fuse is sitting loose in the fuse holder is there anyway making it fit tighter to prevent it from being so loose? I have read every other post online about the problems and tried everything they have recommended but still can not figure out what was wrong with my truck. I disconnected the fuel filter heater, and also the wastegate solenoid to see if that would prevent the truck from shorting out if I pushed the fuse it did not work.
What the problem could be causing the #30 - 30 amp fuse to be shorting out preventing everything from working? Or how to test the fuse panel and all the relays?
I have a 2010 F250 with the V10 and 42000 miles. Lost*power*while pulling a trailer. Couldn't get over 30 mph. Tried turning back home and lost all*power*and would barely idle. Fuel filter good air filter good. Code P0300 came up. Towed it back to the house and then couldn't even get it to idle. Wouldn't throttle up past about 2800 rpm. Cleaned MAF sensor and nothing. Somewhere during all that P0174 code came up and misfire cylinder 10. Cleared codes and they haven't come back. Now when trying to crank, it barely turns over, yet battery is good. Opened air filter cover after getting it to start one time and there was some light smoke coming out. Also while barely keeping it running for a little bit, the catalytic converter on the driver side was fire hot and the other side I could grab with my hand.
View 6 RepliesI have a 99 350 sd 7.3 low power black smoke sets a p1211 under heavy throttle. Check icp on scanner under heavy throttle falls from 1900s to mid 1700s ipr duty cycle runs about 62% wanting to know if I am looking for a hpop problem or injector issue...
View 1 RepliesI just got a 2005 F-350. I would like to get the spare tire out without damaging the unit, but don't have the key. Is there a trick to getting it out? Would there be a way to get one from a dealer?
View 3 RepliesI can't remember my door code and don't want to take it to the ford dealership and pay. I know there is a code up under somewhere but I can't find it? 2005 f-250 lariat.
View 10 RepliesHaving an issue with my 04. Wife got in the truck to move it and no dome lights no crank nothing. Swapped the battery for a new one. Still nothing.
I checked all fuses. I literally was just driving it 10 months prior to her getting in it. Said dome came on for a second then shut off. 2004 F350 5.4 ....
I have an 05 F-250 with the 5.4 liter motor, 4" lift, 35" tires 4x4. I have not had any problems with the truck and have 110,000 miles on it. the only thing I even did to it was replace an alternator. Recently it seems to have lost power.
I use the truck mainly for hauling my smaller horse trailer which is roughly 7500 fully loaded but most times i haul it at about 5500lbs.
I also have a 2003 7.3 which we pull at 20,000lbs no problem
I was driving down the highway and the truck was in overdrive and under a load passing at about 20lbs boost and all of the sudden I lost all power, felt truck shake a little. The tow/haul light is flashing and got only one code P0730. The truck won't go into gear in either forward or reverse now, had it towed home and put a pressure gauge on it and found about 100psi at idle In neutral, in reverse and forward I got strange readings the pressure goes way up momentarily then down to 100psi, and increments back up to over 500 psi and seems to stay there but neither forward or reverse engage. I have no clue what could be wrong at this point. I am attaching a video .....
View 14 RepliesI had a 05 f350 5.4 3v come into my shop with a CEL. Did the usual it had a p0307. So I did the usual again changed plug and coil plug cam out no prob they were done 15k ago. Test drove a few times and it was fine. Few days later customer brought back with same code p0307. thought maybe I got a bad plug or coil so I moved them to #6, misfire stays on #7. When I drive it local its fine when I go to pull on to highway and really put my foot in it CEL flashes (misfire) and it pings like crazy and loses all power. Scan it back at shop and still only p0307!!
View 10 Replies2010 F350 in my shop today. so, before dismantling the entire top of the motor for this inbred oil cooler job, is there anything else responsible for the P012 engine oil temp issue? it throws the wrench icon and cuts power and i pulled the P012F code.
View 9 RepliesJust picked up new 2014 F350 lariat today and I can't figure out how to change the keypad code. I enter the factory code and hit add, but when I enter a new 5 digit code it wont let me hit enter.
View 2 RepliesI don't know what is wrong with my truck. I don't know what this symptoms called, but It felt like it was missing a beat. The engine suddenly lost power for a second or two wile driving. It did this few times. Is it the engine or the transmission? No check engine light is on. 2001 F250 5.4 V8
View 8 RepliesI have a 2011 f250 with the 6.2 liter gas engine. Lost power and the check engine light came on. I pulled the codes and it is a camshaft position sensor and 4 other codes for misfire on all cylinder for that bank. I can't find any info on where the sensor is located or how to replace it.
View 2 RepliesI'm trying to find to rear axle ratio on my 2001 F-350 dually and the axle code seems to be missing.
View 12 RepliesWe just bought and '05 F350 Turbo Diesel, about two days after getting it the check engine light came on. We had the dealer check it since the mechanic wasn't in and it came up as "Fuel Level Sensor" . My husband can't remember the exact code. We have been told it's no big deal but we want it fixed and the engine light to go off. The dealer is giving us the runaround, or at least I think so.
View 14 RepliesI have a 2006 F-350. I got a code p2623 ipr circuit open. I ordered a new one and currently waiting on it. I pulled the old one and the screen has been replaced already. How often do these valves go bad? Is there anything else I should check?
View 6 Replies2008 F350 6.4 ... So I've been reading all about the spartan tuner throwing the P0088 code, and the ford band aid fix, I guess my question is, I'm going to have my HPFP replaced for peace of mind. Truck has 106,000 miles on it. Will i have an issue at the dealer if I show up with my tuner/exhaust on the truck? I'm not worried about warranty obviously, I just want to know are they going to have to unplug the tuner? Or something, I am just concerned how they'll go about putting the new HPFP on.
View 6 RepliesMy buddy has a 2002 F350 CC Longbed with a 7.3. Last night the overdrive light started blinking. He said he drove it today and it takes about a mile or so for the light to come on but then it is a steady blinking. Truck has about 254K miles on it. He said other than the blinking light everything seems normal. How to figure out what this issue may be?
I got AE hooked up on his rig.
When I pull (ALL) codes this is what I get:
When I pull (Current) codes I get this:
I tried to clear the code and the light stopped blinking, but he said it started blinking again on the way home.
I keep getting a lean bank code. I have cleaned tb and replaced one of the rubber lines. It only comes on when I take a good ride with the truck. Not sure what else it could be. I'm thinking O2 sensor maybe.
2008 F-350 5.4 3V. 65k miles