Ford Super Duty (1999-2016) :: 2004 F350 - 4wd First Not Shifting To 4lo
Sep 23, 2015
On dads 04 f350 the 4wd first wasn't shifting to 4lo. Would do 4hi and 2wd fine. Then motor on t-case went bad. Replaced motor 2wd and 4hi still good still no 4lo. Then just 2wd so we unplugged t-case motor and power probed motor got it to do 2wd, 4hi, and 4lo. So we thinking bad dash switch but power probed it and its working fine. So we r thinking VP4C3F-14B128-A/ chassis computer bad just behind/above glovebox. R there any test we can do to confirm its bad? We called local junk yards to see bout getting one, nobody had one. If this is indeed bad where is cheapest get one? What all years use this certain chassis computer??
View 5 Replies
Advertisement
Bought truck drove it 240 miles on interstate 80 mph no problems---2001 F350 4x4 auto. Next morning backed out drive and trans fluid trail 6 inches wide. Didn't leak in forward gears (at that time) added fluid and drive to town shifted fine.
Next day gonna drive 150 miles to check out leak. (Son was driving it) said it wouldn't go over 40 mph. Revving high. Hauled truck here on trailer and pulled tranny. Rear housing cracked just before 4x4 adapter. (This trans was rebuilt 10k miles ago) ..
Got used 4R100 from friend who replaced only because he built one for his truck. It was shifting fine etc when pulled 6 months ago. Used cracked trans TC and installed. Test drive no 4th or OD. Pulled trans put TC that came with trans in. Still no OD. Put on scanner while driving. Trans is being commanded to shift to OD but not up shifting. 45mph at 2400rpm.
Pulled plug to solenoid pack inside trans ( this should make trans default to OD / limp mode) still no OD and won't go over 45.
Pulled OD button checked wires inside steering column. All looks great. Not even a heavy rub mark.
Should I replace the coil pack in trans? Where do I go from here? Again this trans was known to be good when pulled 6 months ago.
View 4 Replies
2002 f350 7.3 ... problems started all of a sudden one day. I have an edge evolution tuner in my stroke. I have it set to make all of my shifts firm. One day it started shifting really sluggish between 1st and 2nd gears only. It don't do it all the time, but it does it more often then it doesn't. I have also noticed when i come to a complete stop and then start out again it seems that it doesn't downshift all the way back to first and when i hit the gas it seems to kinda be stuck between gears and it barely moves until i get the rpms up before it will ease its way into 2nd and the converter locks up.
It shifts a through all the other gears just fine nice and firm like it should, its just the shift between 1st and 2nd. Im wondering if maybe it might be the speed sensors or maybe the tranny filter is getting clogged up? The fluid in it is still nice and red and up to the level it should be. I just bought the truck in october and the fluid was nice and red when i bought it, but who knows if they changed the filter. I have had NO tranny problems with it up until a few days ago when this little problem started.
View 8 Replies
I have a 2011 F-350 6.2L that has extremely hard shifts from 3 to 4 going up and 2 to 1 going down. Sometimes on downshifts it feels like something has ran into the back of the truck. I had the computer updated when the truck had approximately 40,000 miles on it and he assisted a little bit. The truck now has 140,000 miles and it is back to shifting horribly. I put it in the shop at the dealer on 30 December 2013. The dealer says that the problem is that the shift solenoids need to be replaced but that they are not available. The truck is still sitting at the dealer and I am being told that the parts should be available mid February.
View 10 Replies
Ok so some one locked my hubs and put the truck in 4x4 4low i assume my aunt was driving it, truck wouldn't shift from 2 to 3rd is this normal since its in 4low. The shifter also seems pretty stiff and 4wheel isn't used much if there a way to know if 3rd gear toon a crap? Trans fluid seems fine not dirty or burnt...
View 1 Replies
My buddy's 2001 7.3L F350 has had 3 transmissions. Rebuilt and used. Once the new trans is in he goes like 15 miles and then is starts shifting hard and grinding gears. What this could be?
View 8 Replies
I have a 97 F350 5.8 with E40D trans. I bought the truck with it shifting hard thinking maybe a simple filter/fluid change would fix it. It may have worked a little but did not fix the issue. There were 3 or 4 codes that I have already cleared up with new parts. I am still getting a 327 (something with EGR?) and 629 (Converter clutch control circuit failure). These show up in KOEO and KOER self test. The O/D does not flash ( bulb does work).
Parts that have been replaced: VSS, MLPS, new connector going into solenoid pack (tabs were broken), TPS. Removed the trans wiring harness and there is no damage or loose connections. When I replaced the solenoid connector I noticed there was some trans fluid in the connection. I cleaned it the best I could and reinstalled with dielectric grease.
The truck runs fine and shifts in and out of every gear fine its just shifting hard. If I unhooked the battery it will shift perfect for 5-10 minutes but then the hard shifting returns.
The only other thing I can find with my research is maybe the solenoid pack needs replaced. I figured if I take it somewhere they are going to want to rebuild/replace transmission. It seems like it can't be something very major since it will shift fine when reset...
View 4 Replies
I have a 2004 F350 with the V-10 with a Fleetwood motor home on it. 46000 miles.The fuel pump started acting up and i have low fuel pressure. after a lot of testing i replaced the pump and all the hoses on top of the tank. of course you have to pull the tank to do this.
Nothing was touched to my knowledge that has to do with the ABS system.
After everything was put back together and i started the motor. the ABS light came on as usual during the pre-check then went off, and after a couple of seconds came back on, and stays on. it does this each time its started.
I read the most common problem is the rear speed sensor i tested it and it measured .95 oms so i replace it. the new one measures 1.8 oms.
Light is still on. so today i will be testing the front. to insure they are good. The fuses tested OK. My question is what else should i be checking?
View 12 Replies
My 2004 F350 6.0L v8 has a weird shake when I get between 45 and 55 mph. Doesn't feel like its the tires, feel like the engine. I think I might have the #5 glo plug out. Is that it or could something else be wrong? If it is this how bad is it to drive on.
View 4 Replies
I have a 2004 F350. I go out to start my vehicle and it may or may not turn over. Other time it starts fine
View 1 Replies
Truck started to feel like it was missing here and there. A couple rough starts in the morning and a very potent exhaust smell at startup. Then finally after a couple days of this, it wouldn't start.
At first it would try to turn over and almost did several times, then it degraded to just churning and churning with no close attempts to turning over. No codes thrown when we hooked up the code reader. I've had the IPR go out on me twice, the churning and churning is how it acted when the IPR(s) had gone out.
Towed it home and pulled the IPR, everything looked in order with it. Changed the upper fuel filter and oil/filter in an attempt to rule out the easy stuff. Tried to start it up last night after doing this and it churned and churned for awhile (about 2 minutes), then it almost turned over several times. By this time the batteries were too low to continue. Hooked up the code reader again and still no codes.
I'm planning on charging the batteries and replacing the lower fuel filter today, but not feeling real optimistic that it will do the trick. Any other issues to check for?
View 14 Replies
Well long story short, I had the the factory hubs in my 04 f-350 and I was driving down the road and it started making this horrible popping noise. So I pulled over and couldn't find anything and just curiosity locked in the hubs and all was fine. Made me think my hubs were bad, so I went and bought the warren premium hubs, installed them. Went for a drive and still the same noise is there when they are in free spin. But once they are locked in its fine. What this could be? Wheel bearings?
View 4 Replies
My 04 F350 has a bad shudder when slowing down between 30 and 10 MPH. Not so noticeable at other speeds and almost nothing while speeding up. How to fix?
View 1 Replies
The transfer case on my 2004 F350 6.0L 4WD DRW, 230K miles, just blew to pieces Sunday night. See images below. What could cause this?
I just had the front drive shaft rebuilt with new universals and ball. It was making a metallic squealing noise after this.
I noticed that the front drive shaft did not spin freely when parked in nuetral and set for 2WD. I thought the front drive shaft would only engage when in 4WD.
View 14 Replies
My 4wd doesn't engage on my 04 powerstroke. The dash light doesn't come on. I replaced the relays, switch, and 4wd module, I checked the fuses, all fuses are good, but fuse 31 doesn't get power to it. The voltage at the relay block reads 12v with the fuses out, but drops to around 7v when they're plugged in. I have no power to the Tcase (.15v).
View 11 Replies
I just bought an 04 F350 with the 6.0 diesel. I have the trip computer but it doesn't seem to be working, the screen is just off. Tried the buttons, nothing. Checked the manual, can't find anything. Is there a trick I'm missing? Or is mine broken?
View 3 Replies
I have a 2004 F-350 diesel. My vent selector is always on defrost so I suspected a broken hose but traced all out and all seem to be fine. I disconnected the line coming from the pump to the tank and no vacuum. The pump doesn't seem to be running but it's hard to tell with the engine noise and vibration. What tells the pump to run and how can I bench check it?
View 8 Replies
I just bought a 2004 f350 4x4. There is a horrendous clunk coming from under the cab as soon as I steer and at certain rpm while driving straight. I have researched this topic for hours and everyone says sway bar links. Well here's what I have done so far and the truck still has the same terrible clunk. New sway bar links, new sway bar bushings on axle, new front drivers hub, new front passenger hub needle bearing, both front dust seals on axle, greased all ujoints and balljoints, tightened up some bolts for the dual steering stabilizer, and shook the heck out of all other ujoints and the cab mounts and they all seem good...
View 14 Replies
My 2004 F350 would not start yesterday, for the second time. I had just been driving it 30 minutes before, but when I tried to start it nothing happened. The dash light came on but nothing else, not even a click. Had to leave it overnight, and this morning it started completely normally. what this might be? It seems kind of like a relay or reset that was cut off and took time to reset itself. The first time it happened, it started up after 20 minutes, but yesterday it still wouldn't after an hour at which point I had to go to work so I don't know what the interval would have been if I could have stuck around and continued trying it.
View 6 Replies
I just brought home an 04 F350. It is a V10, 6 speed, with 30,600 verified miles on it. It runs and drives fantastic, and that V10 is impressive! I am very impressed. I have noticed that the compressor cycles, even with the dial in the off position. Is this normal for the super duty, or is something amiss? If something is wrong, what direction do I look in?
View 13 Replies
2004 F350 Lariat Crew Cab. My truck has been repeatedly attempted to be broken into through the keyhole. This time they fully punched it through the door, and now i have a hole where the lock should be.
I researched stuff like jimmi-jammers etc, but for the time being.. I am looking just to pick up a set of handles without keyholes. I have remote-less entry and keypad.
Couple questions... Would rear door handles off a crew cab, fit to the fronts? they look the exact same minus the keyhole.. and this would likely be the easiest to find.
Or... Is there any good websites i can take a look at that will manufacture keyless front driver and passenger side handles? They're textured black, and i would like them to match as best as possible.
View 7 Replies
