Ford Super Duty (1999-2016) :: 2004 F250 V10 Battery Light Flickers
Dec 5, 2016
2004 F250 v10 xtl 260xxx. Started off by using my remote start, truck started up ran for about 5 sec then shut off, then restart itself and shut back off. When I manually started it, it ran fine. I noticed my battery light was on and as I was driving it would flicker. First thing I did when I got home was clean all my connections to see if that worked. Battery light still on, checked my volts on my battery and they were at about 11.8 with a slow but steady drop while truck was idling.then checked my alt, that too was at about 11.9 with a stead drop.
Alt was only about 7 months old and I had a warranty on it so I had it replaced at Napa and had them test it there. Good alt. Installed the new alt charged up my battery and turned it over. Battery light still on and flickering. Checked all my wires for corrosion, checked all my grounds. Everything checked out. Checked my battery again 12.4 with the truck off, cranked it over and it was back at 11.9 with a steady drop and almost the same reading with the alt. I replaced the battery as well yesterday, seeing how it was about 7 years old.
View 5 Replies
Advertisement
I've been having issues with the charging system on my 2005. The battery was 7 years old, so I replaced it. Now, the battery light comes on dimly (and flickers) when at low RPM. I am thinking alternator. I replaced one on my 2002 F150, but haven't done a 250. How hard are they to get to and replace? This is on a 5.4 gasser.....
View 3 Replies
The battery light blinks in my truck. It's not a controlled blink, but it flickers like a loose bulb. It started a week or so ago. It would blip every once in a while. Gradually it would start to flicker more often. At first I thought it was belt-related but it isn't related to the transmission shifting at all. So if you're thinking that it's belt-related, you're going to have to explain why it doesn't blink either right before or right after a transmission shift (i.e. a rapid change in engine speed).
Earlier in the week, the light was flickering so hard that it was virtually on. I drove home last night and didn't see it once, although that's the first time I haven't seen it happen at all in a week. The battery gauge itself doesn't move a bit while this is happening. I have a cigarette lighter voltmeter and it shows a pretty steady 14.1 volts regardless of whether the light is flickering or not.
I had the batteries tested in my truck by a real battery shop about 4 months ago and they are fine. The battery connections all seem tight and clean, and the belt, tensioner and all that seems fine. So..What can cause a battery light to come on that isn't voltage related?
View 10 Replies
for some reason my battery light flickers when im driving regular and on the highway. I have had both batteries checked and they were at 50 percent charge and both were good so therefore I assumed it was my alternator. I removed alternator had it check and it passed all test. Everything was checked at o'reilly and autozone
View 8 Replies
I was driving and all of a sudden the radio died, battery light came on, Power windows and interior lights died, gauges died speedometer went all the way up to 100. The Head lights, turn signals and heater work. When I got home I opened the hood and the battery was boiling.
View 14 Replies
I have a 2003 f250 super duty with a v10
i was towing a trailer up and down lots of hills and the battery light on the dash came on. there was no effect on the performance right away. as i kept driving into town i was starting to worry if i would make it.
as i pulled into the carls jr parking lot, the ABS light came on, all the gauges shut off and the truck died just as i pulled into a parking spot.
i figured it was the alternator, had it tested at AutoZone (failed twice) so i swapped it out for a lifetime warranty AutoZone one (very small town, nothing other than an AutoZone)
the truck started after being jumped but the battery light was still on. i figured that the bad alternator killed the battery. the battery was 4 years old and they usually only last 3 years in the AZ heat so i bought a new duralast gold.
the battery light was STILL on after that. the Autozone guy ran his test--- engine off- battery tested fine starting---he said something was wrong with the starter (but it cranked awesomely!) running--alternator tested fine
i just can figure out why when i drive down the road i dash light will turn on and off at random times. the truck seems to run fine. I've even been under the hood shaking the wire while i had someone watching the dash and i cant seem to make the light go on or off
View 1 Replies
03 f 250 super duty, my battery light came on and when I accelerate my dash gauges shut down and radio turns off, if I idle or stay under twenty MPH, everything works fine. Battery and alternator test good, lights never dim, any thoughts
View 4 Replies
The light on dash for 4X4 stays on no mater where the switch is placed I have it in 2 wd and it stays on. Where I need to start looking.
View 4 Replies
I have an 04 F250 4x4 king ranch with a 6.8 V10.
When I first bought this truck it had a problem of stalling out at stops. You could sometimes hold the brake and gas and push your way through it but it would sputter for a second and try to die and then it was fine once you got going. The OD light would flash, check engine light would come on and it would throw a P0720 code for the OSS. I did some researching and I pulled the sensor in the pumpkin before that because I read that could cause the same problem, so I cleaned it and put it back but it didn't solve the issue. Then found that an K&N air filter can often times clog the MAF and cause the issue so I pulled my air filter and sure enough it was a K&N, I swapped it with a normal filter and sprayed some MAF cleaner and its been running like a top for months... until now.
It started again, gradually at first. It would die when I started to back the truck at a very low speed to load my 4 wheeler. I fired it up and it was good again for a couple more weeks, then I went to hook to a horse trailer and I was having to back up a hill to get to it, and it just kept dying, OD light would flash, check engine light came on. I was in a bind so I just tried wiping off the MAF with a rag, that didn't work, my girlfriend was using the truck and said it kept dying whenever she stopped. I got it home and cleaned the MAF with cleaner really well but the problem persisted. I went ahead and changed my oil, spark plugs(gaped at .052-.054), replaced the IAC(which looked like it had been installed once before so I am guessing someone tried it and when it didn't fix the problem they returned it) and changed the fuel filter. I drove it around and it ran fine, drove it to work and it ran fine, my girlfriend took it for about 15 minutes to run an errand for me and it was fine until she got back in the parking lot and liked to never got it parked again it stalled so much.
So I went back to the drawing board and read that it is rarely the OSS that is the problem but that often times the issue is a bad coil pack. I don't have a scanner nor do I know how the heck to use one. I plan on going out of town at the end of the week and the truck has 194k miles on it so rather then take it to a shop and try to find out which COP was bad I just decided to replace all of them(I know, I know, you should never just start replacing parts). I only had time to replace 5 of them, I took the truck out and again it dove fine for an hour, went through traffic OK. It sat for an hour and when I left it started to die again, I could drop it in neutral and it would fire back up and as long as I gave it just a hair of throttle it stayed running fine, take my foot off the fuel and in a minute it would die again. After I drove for a bit it was fine again. Now I know the problem may yet be in the remaining 5 COP that I must change tonight but in case it is not I wanted to get input on this.
I've read the problem can come from a bad ground, so I took every ground point that I could find under the hood and I cleaned the connectors and took the paint off at the connection site just for good measure. The problem persists. I've read that sometimes a diode can go out on the alternator and cause this problem, I did use my amp meter and I'm checking out at 13 volts while running. I'm not the best with meters so I'm not sure how else to check the diode?
I've also read that taking it to a dealership is hit or miss for them diagnosing the problem, sometimes they find the issue, sometimes they just change the OSS. The only mechanic I trust closed his shop and is now service manager of the Dodge dealership. I'm thinking since this seems to be a common problem that maybe ford might have more knowledge of it then dodge but I trust the dodge dealership more because of who is over it. Either way I know it will sit in a dealership for awhile before it ever gets looked at and if they have to chase any electrical problems then that starts racking up $$ fast.
So what am I missing? I've thought about replacing the MAF since cleaning it the first time solved the problem. When it did this the first time I still had my 01 F250(it never gave me problems like this) and so I took the MAF off of it and swapped them and sure enough it fixed my problem so I switched them back after I cleaned the MAF and like I said it's been running fine until recently. I'd rather not throw money at this by replacing parts and hoping for the best. I've also read about tracing the harness that runs from the sensor on the pumpkin to the OSS and on. That harness runs through all kinds of stuff so I'm dreading that but it will also be a next step. I haven't pulled the OSS because its in a very awkward position on my truck.
View 1 Replies
I've got an '04 F250 4x4 gasser with a 4R100 tranny. I was driving home from work earlier when I noticed the overdrive lockout light was on. Not flashing, but steady like I'd accidentally locked out the O/D. I pressed the button to turn it off, but it stayed on and the O/D locked out for real. WTF?......I pressed it again, the light stayed on, but the trans shifted back to 4th like it's supposed to. I was near freeway speed, so I kept an eye on the tach for a few miles. Everything looked normal, except maybe the converter lockup seemed a bit sloppy whenever it downshifted/upshifted on a hill. That could be my imagination, though. I was in full AWACS mode by then, watching everything like a hawk.
Then I started wiggling the shifter a bit. I pushed the lever down against the detent, and the light went off. I let it go and it came back on. I did this a few times with the same results. It didn't affect the tranny operation. I pulled the lever back toward me like I was going to shift, and the light went out. I let it go and the light came back on. By this point I think I can rule out any major tranny problems as it seems the problem is in the wiring to the light, not to the O/D lockout circuit itself. I was thinking maybe a short to ground somewhere. What controls the lockout light, never had to deal with one before. I'm hoping for a easy answer before I tear into the steering column and start poking around in the harness.
View 1 Replies
Driving to work the other day my transmission shifted down and the transmission light started blinking. It felt like it geared down like it was in 4x4 I was doing about 55 at about 2600 RPMs. This has happened twice now and lasted around 2 minutes then stopped and ran great.
View 2 Replies
I was cruising my truck down the road and noticed that my high beam indicator light was very dimly lit. I wondered why this would all of the sudden come on at all if the high beams were not on so I pulled over and took a walk to the front of my truck to check my headlights. Sure enough the passenger light was very dim. (I must assume the high beam indicator light being dimly lit is also an indicator for headlight malfunction/burn out)
I figured out the plug has a keeper piece that is supposed to hold it in the bulb base but it was broken off and missing.
I went to the auto parts store to find some kind of fix. To my surprise they have a replacement plug for my truck. The down side is it costs $95 and it still had to be shipped! I decided I could figure something else out.
After I pulled the four 5.5 millimeter screws out of the headlight housing. I noticed there is enough room on either side of the light contacts to drill a hole thru the plug and the bulb to allow a pin to be placed thru both of them which would keep the plug and bulb socket from coming apart.
These are the pins or keepers I used.
A 1/16" drill bit did the job. I put the new bulb/socket and the plug together and drilled a hole on each side of the plug right thru the socket at the same time far enough back and at a width to avoid the contacts of the bulb socket and plug. (there is a rubber gasket in the plug that should be avoided but if you still knick it as I did you can fill the plug or the socket with dielectric grease that most car parts stores have and it will keep any moisture out but not effect the electrical current, do not use silicone, one day you will have to take it back apart for a bulb replacement or something.)
This is the bulb socket with the holes already drilled and the plug removed. This is what it looks like with the bulb/socket and the plug together and the keepers in place. And the back of the composite headlight housing with the assembly installed.
Make sure you install the bulb/socket and plug with keepers on the housing before you bolt the housing to the truck because there is not enough room to get your hands behind the housing to install the keepers with the housing bolted to the truck.
Since I replaced the stock bulb with a Sylvania Silver star I had to replace the driver side too so I didn't end up with a headlight being brighter or "whiter" than the other. Even though I was incredibly careful I still broke the plug on the driver side too! So now both of my headlights now have this mod on them.
View 5 Replies
I have a 1999 f250 super duty and something keeps draining my battery, I replaced the old one and im having the same problem. What could it be?
View 14 Replies
2013 F250. Wife turned the ignition on to roll up the windows before the storm (good thing), but left the switch on. Both batteries dead. I charged them both (although not completely). Started OK but have a check engine light on. Should I just put the batteries back on charge?
View 5 Replies
I have my 2004 f250 6.8L. Recently my truck has been having issue with the oil needle. When im stopped or coming to a stop my Check Gauge light comes on and my oil needle drops all the way down. As soon i step on gas it goes right back up. What could it be?
View 7 Replies
I did some reading on here this morning and ended up at 1A Auto looking for mirrors. I want to make sure I get the correct thing before ordering. I have a '04 250 with factory tow mirrors that are power mirror and turn signal/clearance light. I want to upgrade to the '08 style. Which of these would work? I would think either, but I'm not sure about the wiring harness?
Search Results for 1AMRP01095 - 1A Auto
2008-10 Ford Mirror Pair - 1AMRP01096 at 1A Auto.com
View 8 Replies
Like the title says, if it sits over night the battery will be about dead. The cables were replaced 6 months ago and are in good shape. I could not find and bad spots on the wires I can get to. One odd thing to note, with the key out of the switch I opened the passenger door to check the glove box light and the truck started chiming like I had opened the drivers door with the key still in the switch. Would that indicate maybe the key switch could be the issue?
View 14 Replies
So two weeks ago I had a battery melt on me and I replaced it. Then last week I had the other battery almost blow up on me (it was a mess and smoking). I didnt use it all weekend. Today it started right up. I drove it like 500 feet and it just died. It is very weird. Both batteries are fully charged. Relay is good. When I put in the key it does nothing. No sound no radio no clicking. However, the gps still works (the online monitoring kind). I can fold in my out revie mirrors. And I can lock and unlock the doors. and the interior overhead lights come on. Nothing else has power at all. And I can't put it in neutral. Right now the truck is blocking my driveway so nothing can get in or our of here. I am wondering if it is some type of antitheft issue...
View 5 Replies
I have a 2004 F250 Torqshift trans, 155,000 miles. It has had a slight hesitation when trans is engaged for about 4 years, not a problem the dealer has no fix they said.
Now today for the first time I had a tow haul light come on while driving on the freeway. It would not go into overdrive and the light keep blinking. Later in the day, I let it cool down and it drove fine to the store about 2 miles. When I got in to drive home it had tow haul light go blinking and check engine light came on this time.
I hooked up my code reader and it's giving codes: P0720, P0751 and P0766.
Should I take it to the Ford dealer, a Transmission shop or have a friend who worked at Ford Dealer do the Work? I see that some people have changed out the TFT sensor and corrected the problem. While the pan is down should I just have all the shift solenoid sensors changed?
View 11 Replies
Took in the alternator to get it checked and they said it was good. Put it back on and it seemed like it was charging according to my volt meter (14.24-13.5 v)
Today, it's not charging. Only reads 12.2 v while running. Is there a fuse or something I need to check? Grounds? It seems intermittent.
2003 F-250 V10 6.8 liter 255,000 miles.
View 4 Replies
I have a 2006 F-250 5.4L (6spd manual). I would like to add a second battery. It would be a purely auxiliary battery for radio use, and would be connected to a battery isolator. It would likely be a 33AH SLA, and starting capabilities are not required.
Any clean way to mount a second battery under the hood? On the driver's side, directly above the wheel well, there is an adequate amount of room for a second battery, and there are even tapped holes that seem to have identical spacing to the ones for the factory battery tray.
This leads me to believe that some version of this truck is offered with a second battery (the Powerstroke, maybe?). The local Ford stealership was all but useless, which is pretty standard. They have a solid reputation of not giving a crap about you unless you want to purchase a brand new vehicle with dealership financing.
What is the part number for a second, driver's side battery tray? I really am NOT interested in any kind of solution under than under the hood (no frame rails, or relocation to the bed).
View 4 Replies
