Ford Super Duty (1999-2016) :: 2004 F250 XLT - Slight Roar Coming From Left Front Wheel
Jul 11, 2016
I'm looking at a 2004 F250 XLT super cab 4x4 with a 5.4L with only 50k on the clock. It looks to be in great shape and drives good with only a few issues. Cruise doesn't work, it pulls to the left a little, and it has a slight roar coming from the left front wheel. Other than that it seems to be a nice truck. Its blue and grey two tone. Anything else I need to look at before pulling the handle on this one?
View 11 Replies
Advertisement
My 99 F250 has just recently started making a "rattling" noise. The noise sounds like its coming from the front left wheel area. The noise is constant while driving down the road, its NOT created by bumps or anything, its a constant noise while moving.
View 3 Replies
I noticed a slight whistle last year coming from my front left hub. I pulled the hub and greased the gears as best I could and it sort of went away. Now this year it is a little louder. It only happens when the hub is locked. Is starts around 20mph and goes away at 40. Is the bearing in the hub shot or is this normal. 4x4 works fine and there is no visible excess wear on the gears. The truck has 93k.
View 6 Replies
Early 99 F250 7.3 Manual 4WD Extended Cab Short Bed
I am at a loss. I have a slight vibration/medium roar seemingly coming from front. I have tried fixing/replacing several things, with no luck. When I get above 35-40 mph, I can hear a whirling vibration that sounds like tire tread noise (very little tread on tires). When I tap the brakes, seems to make a difference, seems to get louder as I slow down. I can feel it in the clutch and accel. pedals. It is consistent, when I push clutch in and let idle at 45mph, it is still there. Doesn't seem to make a difference when swaying back and forth, maybe a little. When i get below 25-30mph it isn't noticeable.
Here is what i've done so far :
1.Replaced both front wheel bearing assemblies, rotors and brakes
2.Replaced drivers side brake caliper (seemed to be sticking a bit?), will do passenger side tomorrow
3.Serviced both hub locks and verified front axle is not engaged (one was locked for some time, I thought I found issue, but still have vibration)
4. Tightened pitman arm joint, was slightly loose (need to replace)
5. Inspected tie rod ends and other joints, see no noticeable movement, but have not marked them off the culprit list.
6. Tightened output shaft nut, was a little loose
7. Raised rear end off on jack stands, and revved up to 50 mph, and no vibration, so I have excluded u joint and cardan joint, everything points to front end
8. Rotated tires, left front to right rear
What I haven't done :
1. Have a leak in pinion seal, not replaced yet
2. Seems the upper and lower ball joint had the slightest, I mean slightest play in it when lifting the front driver side wheel (I mean less than 16th inch) but could hear it. I haven't done anything with this yet ... may be the problem? Would a tire out of balance wreak this much havoc with this amount of movement?
3. Haven't replaced the pitman arm joint, will but not sure if this can create issue.
Nothing I've done seems to make a difference.
View 14 Replies
So I have to replace the front unit bearings on my 2004 f250 4wd. My question is, which thread pattern I have, fine or coarse? I have read that the early models, 99-02 have coarse threads. Afterwards they are fine. I am going to order online as they are cheaper than the local parts store. I have the Timken part numbers for either thread pattern.
View 4 Replies
2004 F-250 FX4 SB 5.4 V8 140k
Issue: rattling/clicking noise from passenger front wheel area at speeds lower than 15MPH, made worse under light braking and/or turns to the right.
Clicking sound is speed dependant.
Spindle? Hub? Balljoint? Sway joint? Rotor Issue?
View 14 Replies
I have a 02' 250 4x4 with 250000 miles on it. While driving between 55 to 65 mph there is a roar and vibration that seems to be coming from the rear. I have about 35% tire tread left and have had the rear tires balanced and it still does it. Having issues with drive shafts unbalanced or rear ends?? I am not sure where to start....
View 1 Replies
I had a 2014 F-250 I bought new. Absolutely loved the truck. Things got tight so I decided to sell it yesterday. I'm now looking at a 2005 F-250 with 113k miles. It's got a lift, 37" tires, DPF delete, pretty sure the EGR delete but not sure exactly what to look for under the hood. A ton of LED light bars, SCT tuner, I was told its bulletproofed by a dealer, and it's a king ranch. It runs great. I plan on having a diesel mechanic look it over but here are my concerns. It does have a slight bit of blow by coming from dipstick. Very little. Also a slight oil leak that looks like it's coming from the bell housing so maybe rear seal?
View 14 Replies
I had some steering issues with my truck so took it for an evaluation at pep boys. They recommended a new steering gear box and tie rod that hooks to the pitman arm so I had them replace them. Steering was improved but now the wheel is canted to the left or right depending on when I make a turn. When I make a left turn, the wheel is canted about 10 o'clock. When I make a right turn, it's canted about 1 o'clock.
I looked under and had my brother turn the wheel and didn't really notice any thing loose. I lifted the front and noticed the left wheel bearings need to be replaced. I also noticed the shocks were shot and replaced them but it didn't make a difference in the crooked wheel.
Do you think it's the wheel bearing that can cause this? How about the ball joints? The truck has 407k miles and I bought it a month ago. Previous owner said he never replaced any steering components. Should I just replace all steering components with the Moog kit? I'd like to hold off on the $600+ kit for now as I just bought a a boat and the boat needs some stuff. I hope to find that one thing (hopefully not more) that's loose.
View 7 Replies
2002 Ford F250 4x4 Superduty Lariat (4 door). Just changed the locking hubs to a new set of Warn manuals. I began to periodically hear what sounds like a rumbling/bearingish/howling kinda sound. Happens when you hit a bump at any speed...then howls till you hit another bump..goes away..then process repeats. Come to a complete stop, and the sound usually goes away till you hit another bump. The hubs are "free" at this time.
Heres the weird thing...when the noise starts...I switch it into 4 wheel drive on the dash...the sound instantly goes away. Click it back outta 4 wheel drive (hubs are still unlocked this whole time) and the sound is gone. drive some more down the road, maybe hit a slight bump, and the sound returns. Switch it back into 4x4...sound instantly goes away. Its not really in 4 wheel drive, cause the hubs aren't locked in...but that cures it till I take it back out. What could be causing this howling ? Its getting worse, and you can feel a slight vibration in the floor now when its doing it.
View 8 Replies
1999 F250 SD 4x4 7.3 PSD ... My truck has 198K miles on it. It pulls to the left as I drive it. So I took it to a shop to have the alignment checked. They told me that the front outer tie rod was bad and needed to be replaced. And of course they said they needed to put in a set of caster camber bushings to do the alignment. They quoted $400 to change the tie rod out. I said I would do that. They gave me the print out from the alignment but reading it the only thing that was out was the toe. Left tire was toe out and the right tire was toe in, which to me would cause it to pull to the left.
I got under the truck and the steering link, piece that goes from steering box to right side/tie rod, is not tight...I can move it up and down and it clunks when I roll it up. I have a clunking noise when I drive it and go over bumps also. Could this be the clunking noise? Also, if I replaced the ends of the steering link, that would tighten up but possibly push the steering back to the right some to straighten out the tires? I have read alot of threads talking about the clunking being tied to the sway bar bushings being bad but the clunking I get by rolling the steering link up and down sounds alot like the noise I am hearing.
Also, when looking at the axles where they go into the knuckle, there is a loose plastic ring on both sides. Is this part of the dust shield or an oil seal?
View 5 Replies
I have a 99 F-250 extended cab superduty 4 wd with the 7.3. I also plow during the winter. Recently I've noticed wear on the inside of the left front tire. Brought it to a tire shop and had them check the front end and alignment. They told me that the specs were "within" tolerances" for my truck. I'm stumped as to why the abnormal wear if everything is supposedly good with the alignment.
View 5 Replies
I got an 03 f250 with a 10 inch lift on 40x14.50 tires on 20x10 fuel hostage wheels. They rub my springs pretty bad when trying to make even the slightest kind of tight turn and the sound they make when they rub is even worse than them actually rubbing. My question is should i stay with this tire and wheel setup and try to get some 6061 billet aluminum 2 inch spacers? (I'm not sure about going that route though because of what i heard about spacers) or go down to some 38s with a 20x14 wheel that hopefully would push the tire away from the hub like spacers would do. I'm leaning more towards going to 38s because of the rubbing and also because I feel they might look better on the 10 inch lift rather than the 40s but dont know whats the best thing to do.
View 12 Replies
I got a 2001 f350 got a noise in my left front wheel i know its not the wheel bearings, it only makes the noice when the locking hub is unlocked i did jack the the truck up and spun the wheel got a faint grinding noises form what seems like the locking hub so my question is bad locking hub or needle bearing holding the axle shaft??
View 3 Replies
2003 F250 4x4 7.3L
While doing my brakes in the front, I tried to wiggle the front left, nothing. Solid. Then when I did the right, I was surprised to see it wiggle when I grabbed the tire. So I looked to see what was moving.
Not the U joint, not the ball joints, But it looks like what is a drive shaft.. (I am new to this stuff). On the right side a shaft comes out of the axle just before the U joint and the rest of the wheel assy. What is wrong?
View 6 Replies
2002 F250 4 wheel drive manual hubs, 7.3....
My first thought was to have the tires rebalanced and rotated to see if it is tire noise? I am hearing damage on top of the noise from the 7.3, hard to be sure!
View 11 Replies
I've been noticing a grinding coming from the front end of my 2012 f250 4x4, mostly while turning. It seems like its worse over uneven terrain, bumpy dirt roads, things like that, but I have noticed it on occasion while on seemingly smooth roads. Also a couple times while turning and lightly braking I could feel it interfere with the brakes. They wouldn't grab completely and you could feel the grinding in the pedal. I've been crawling around looking for rub marks or any indication of what might be causing it but until recently I hadn't noticed anything. Today though I found this. I'm guessing bad ball joint or tie rod maybe? Maybe just need alignment?
Passenger side lower control arm ...
View 11 Replies
I have a bad wobble/vibration coming from front end i think i replaced hub locking hubs u joints truck dont feel safe at all took it to ford they say its normal no way its not just starting doing it few month feels like the 4x4 is in use when hitting bumps when driving if you go slight left or right it seems too make act up more.
View 2 Replies
I bought a 2004 F250 Crew Cab LB 4x4 with the 5.4 Motor and when I turn left it has some Tight Spots and I can't figure out why, I checked the Drive axles to make sure the locking hubs were unlocked and they spun freely, I Also have a lot of play in the steering wheel, Could this all be Related to the Steering Box? What else should I check for ?
View 3 Replies
I have a noise with my new (2.6k miles) 2000 Diesel F250 Crew Cab. When I make low speed, right turns while crossing any type of depression in the road I hear a loud knock as if the left shock is bottoming out. There's an intersection near my house with runoff depressions across the road, I almost always hear the noise when making that turn. I've occasionally heard it coming from the right side when making a left turn.
View 14 Replies
I have a 2008 F250 5.4 4x4 supercab long box (68,000 miles) that has a little bit of movement in the front wheel bearing and hub assemblies. Made it through inspection OK but it will need to be changed soon. Just asking for everyone's thoughts on brands they prefer. I have had great luck with Moog brand products in the past. I put SKF hubs on my wife's 2010 Explorer and they I would say are top quality also. Not interested in a conversion kit or cheap junk. I want a good quality unit. What brand has everyone had good results with? Are Moog or SKF the way to go?
View 8 Replies
