I have a 2004 superduty 250 4x4 with the 6.0. I am having a violent shake in the steering wheel mostly and can feel it in throttle at about 45 to 60 and at 72 there is s growel. Have changed tires, wheels checked all ball joints tie rods wheel bearings ujoints. Don't matter brakes on or off, od on or off nothing changes it. I really don't know what else to check.
View 10 RepliesI've got an 04 f250 4x4 crew cab. I just replaced the upper and lower ball joints on both sides and also the drag link. My alignment was off from the bad ball joints so I had it aligned after I did all of this. Now the steering is really weird. Its like something is to tight. I can barely keep the truck straight because every time I barely move the wheel I seem to be going one way or another and getting it straight is nearly impossible to the point I look like a drunk driver. I can turn the wheel to go around a curve and let go of it and it will stay that way until I turn it back. It won't return itself. I'm kind of lost.
View 3 Replies2004 F250 SuperDuty 6.0L Diesel. The turn signal (left or right), it would make a buzzing noise, so I located the relay under the steering wheel (by putting my hand on it and seeing which one was buzzing) and replaced it, I bought a replacement at Schucks, then the buzzing noise went away, and the clicking noise is back.
But.... I don't see the turn signal lights in the dashboard and the turn lights are not working, I checked, what could be the problem ? I read the owners manual, in the fuse box under the steering wheel, fuze #18 is used for turn lights, but it is not blown.
I've noticed when I'm towing, on long down hill grades if I touch the brakes I get what feels like a rotor causing the steering wheel to shake. At first it was only mild, but today on a long 6% grade it got really bad. Never does it on a level road, I've tried to duplicate it, only on a long down hill grade, and I'm not getting a pulse in the brake pedal at all, only the shake in the steering wheel. It's probably time to replace the pads anyhow, and I'll check the rotors. What things to look at?? 2006 F350, 6.0 dually 4x4.....
View 2 RepliesI have a 2002 F250 with the 5.4 triton engine. Automatic transmission. When I reach 35 mph (sometimes sooner) the truck will shake horribly when I reach lower rpms. It will do this up to 65 mph and then it mostly stops. Completely taking my foot off the gas will stop the shaking, as well as shifting into neutral.
I know for sure that the truck has a cylinder 3 misfire as well as a minor exhaust leak, could either of these be causing it? Don't have the money to fix either of the problems for another couple weeks, is it safe to drive until then or should I play it safe?
just bought this f250 seems to walk on the road alot, had it looked at has new balljoints, he says everything seems tight except there is lots of play at the gearbox, is it recommended to have it rebuilt or buy a reman, was told that even the reman seems to be the same way
View 14 RepliesMy 2010 6.4 F250 seems has a loose steering wheel. The steering of the truck hasn't changed nor has there been uneven wear on the tires. It doesn't drift if I let the steering wheel go. Had the front end inspected and was told it's all good under there.
YET, my actual steering wheel is loose. I can grab the wheel and wiggle it front to back and side to side. It FEELS like the bolts that hold the steering wheel to the column are loose. What was the cause/repair? Is this something I can repair myself or a local shop? Or is this a dealer fix?
I have a F250 SD with a 6.0 diesel. My steering wheel is loose. I tested and know for sure is not a problem inside the cabin. Fallow the line thru the linkage to the steering box by the left front wheel. I found an adjustable switch there. Just on top of the steering box. It has a lock nut that must be loosen to adjust what it looks like a hex. Very hard to reach. I have watch some Youtube videos but on different vehicles.
View 1 RepliesI had some steering issues with my truck so took it for an evaluation at pep boys. They recommended a new steering gear box and tie rod that hooks to the pitman arm so I had them replace them. Steering was improved but now the wheel is canted to the left or right depending on when I make a turn. When I make a left turn, the wheel is canted about 10 o'clock. When I make a right turn, it's canted about 1 o'clock.
I looked under and had my brother turn the wheel and didn't really notice any thing loose. I lifted the front and noticed the left wheel bearings need to be replaced. I also noticed the shocks were shot and replaced them but it didn't make a difference in the crooked wheel.
Do you think it's the wheel bearing that can cause this? How about the ball joints? The truck has 407k miles and I bought it a month ago. Previous owner said he never replaced any steering components. Should I just replace all steering components with the Moog kit? I'd like to hold off on the $600+ kit for now as I just bought a a boat and the boat needs some stuff. I hope to find that one thing (hopefully not more) that's loose.
So I have a 2005 f250 Super Duty 6.0 diesel it is the xlt with leather. So I don't much care for the steering wheels on this truck so i purchase a 05 f150 steering wheel. The splines and everything match up but the plug for the cruise control does not, need a wiring diagram or have done the swap and can tell me what wires connect where.
View 1 RepliesI found one thread in FTE regarding replacing instrument cluster bulbs but the solution was to contact Circuit Board Medics. I have one dark area on the right side of the tach and another dark area on the left side of the speedo. Probably the same bulb that's out. Also, can attempt to replace the bulbs (assuming its a bulb and not a fiber optic of some sort) in the steering wheel volume and fan controls?
View 3 RepliesI have a 02 F250 4x4 5.4. As I drive and when pulling into a driveway I hear a clunk that can be felt in the floor and the steering wheel. I've replaced the wheel bearings and seals, shocks, ball joints, sway bar links and bushings, tie rod ends at the gear box and "right hand inner". The other two tie rods are tight and so is the track bar. I cannot duplicate the sound if I jack it up and move parts around with a pry bar. I can however move the steer box sector shaft upwards about an 1/8. I've adjusted the screw but it didn't do anything. Could it be the steer box or the springs? I've even mounted a GoPro underneath but everything moves and I can't tell why it is.
View 14 RepliesI have a ford f250 with a 5.4l 2v engine and lately it started to shake when it idles. i have changed all the ignition coils and spark plugs, the injector are fine, but i cant seem to pinpoint the problem. the weird thing is that there are no codes. the fuel trim on bank 1 is around -8 and bank 2 is at almost positive 20 and higher.
View 14 RepliesBought a new touchscreen head unit to put in my 06 lariat f250. I have all the controls on my steering wheel for heat and radio and I don't want to lose them with a new radio. This head unit does not have the 3.5mm jack for the axxes unit but has 3 wires labeled swc1 swc2 and swc ground. It supposedly has the converter built in. any views on using a headunit with these wires?
View 3 RepliesI have a 2011 f250 6.2 cclb and it shakes around 70 to 75 mph. Not terribly but enough to annoy the crap out of me. Now I have put new tires on it recently, new Rancho 9900 adjustable shocks, I have it aligned regularly and tires rotated and balanced every 5000 miles or so. I have had two dealerships look at and my local shop and they can't see anything visibly wrong with it.
View 7 RepliesI was driving my 99 f250 superduty and out of no where it sounded like i had blown a tire started to shake for at least 3 or 4 seconds pulled to the side of the road got out and check tires were good, got back on the road with no more problem.
View 1 RepliesHaving issues with rear wheel wells rusting, mine is a 2004 f-250. I wax at least 10 times a yr. Can't believe I have rust there...
View 13 RepliesSo I have to replace the front unit bearings on my 2004 f250 4wd. My question is, which thread pattern I have, fine or coarse? I have read that the early models, 99-02 have coarse threads. Afterwards they are fine. I am going to order online as they are cheaper than the local parts store. I have the Timken part numbers for either thread pattern.
View 4 RepliesI bought a 2004 F250 Crew Cab LB 4x4 with the 5.4 Motor and when I turn left it has some Tight Spots and I can't figure out why, I checked the Drive axles to make sure the locking hubs were unlocked and they spun freely, I Also have a lot of play in the steering wheel, Could this all be Related to the Steering Box? What else should I check for ?
View 3 RepliesI have an 04 lariat f350 and after cleaning the steering wheel it is a bit sticky.... What the material is?? Or how to resolve the sticky issue??
View 8 RepliesWhen my truck is parked, I go to the rear tire and shake it back and forth and hear a slight clunking noise from either the tire or rear end. Its like the axle is making the noise?
2000 7.3 Power Strke Super Crew 4x4