Driving to work the other day my transmission shifted down and the transmission light started blinking. It felt like it geared down like it was in 4x4 I was doing about 55 at about 2600 RPMs. This has happened twice now and lasted around 2 minutes then stopped and ran great.
View 2 Replieshad a problem with their OD light blinking and shift problems. This past week my od light started blinking and when I shifted into drive, it was stuck in overdrive. When I shift into 1st it would go to 2nd and stay there. So basically I had 2nd and overdrive. I started replacing sensors like the VSS, and checking the wiring warness. Took it to a transmission garage and they told me it was toast. Then I decided to bite the bullet and buy a new tranny. After replacing the tranny it did the same thing with the same codes showing. Then I got smart and checked the fuses. Of course it was as simple as a blown fuse causing all the trouble. In my truck it was fuse 23 under the dash. A 20 amp fuse that was listed as engine control. Im not saying that in every case if the OD light starts blinking it's as simple as a fuse but in my case it was, so lesson learned. Always check the fuses first.
View 13 RepliesThe problems that I am having at the moment are that the abs light is on from the speedometer, odometer, also the blinking overdrive light that comes on at around 25 mph. After some research I had purchased a ford factory sensor for the rear dif. I then replaced the old sensor with the factory one. Started the truck and not a single thing had changed, both the meters were not working as well as the od light was still flashing.
View 4 RepliesI am new to being an F250 owner. Just recently purchased a 2000 F250 SD 4x4 with the 5.4 and a 5 speed trans. Got a pretty good deal on it, because I knew some work had to be put into it, and do plan on dropping the trans. Currently, if the truck has been sitting for a little bit, not cool, but not running for a little bit, when I start it, whether it is in gear or in neutral, there is a noise coming from what seems to be the clutch area.
After a couple minutes of driving, this noise goes away and all sounds as it should. A little bit of researching turned up the possibility of the throw out bearing being bad, however, I found other posts online that doubt this. Another symptom that I assume is connected is that if I go to put it in reverse at 0mph from neutral, it grinds.
In order to go into reverse, I have to press in the clutch, put it in first, then put it in reverse, at which point it goes in no problem. I had already planned on replacing the clutch because it seems to me that would be the logical choice as to where the problem originates, so no issue there. But perhaps I'm wrong??
I have a '99 F250 SuperDuty Diesel with an Automatic Transmission. There is a button on the end of the gear shift which allows you to turn off overdrive -- in other words the transmission won't shift into overdrive once you press the button.
Here's my problem. I start off driving normally. I've not done nothing to the overdrive button and the truck shifts normally into overdrive. 10-15 minutes down the road, the overdrive light (which indicates the state of the overdrive button) is FLASHING. Pressing the button doesn't stop the flashing. Once this flashing starts, the only thing I notice is a much more abrupt shift from 1 -> 2 gear.
Experiencing a melt down with one of my trucks. One of our trucks is an 06 F250 SD with 80k on a 5.4L and the other day the tow/haul light started to flash. I took it to a buddy's repair shop (who is an experienced Ford tech and tranny guy) any way, it shifted fine until about the last 1/2 mile before I got to his shop, then it started shifting in and out of different gears. He found solenoid "A" pressure solenoid failure and one other solenoid failure, he replaced all 7 solenoids and also found the pigtail from the transmission to the wire harness bad as well and replaced that. I pick it up and get about a mile down the road and the light starts to flash again so I took it back, he ran his scanner and now found something with the coast clutch and through all his testing it told him the coast clutch needs replaced. He removed the trans. and tore it all down and found nothing wrong with anything, in fact he said everything looked in great shape and thinks the pcm failed.
View 12 RepliesMy v10 has a cold miss when i start it in the morning no matter what the temp. It misses until it gets up to operating temp.then it runs fine all day with a slight miss.
- Changed plugs,
- Changed pcv,
- Changed iacv,
- Cleaned map sensor,
- Changed tube to pcv,
No codes. Its running as if it had a carb and the choke is closed. No smoke, tach. idles between 750 down to about 500, until it warms up then tach. Stays steady.
Had a front seal leak on my 2000 F250 V10 with 122000 miles. Since I've towed for years and the tranny had to be pulled I opted to just rebuild the whole tranny. I had problems from the beginning where it wouldn't shift into third and when I took my foot off the gas it would just go out of gear completely and just rev. After I stopped and started over, it would shift fine for the rest of the day.
Finally the O/D stem light started flashing and the mechanic did something to fix it. Since then it has shifted fine but when it went into overdrive the rpm would bump up and kind of slide into overdrive. Left the truck with the mechanic again for two weeks and it's better, sometimes revs and slides into overdrive not every time though.
My problem, besides the overdrive shifting, is it now takes forever to shift in to 4th gear. I have to take my foot off the gas to make it shift into 4th and overdrive won't kick in until 45 MPH. My gas mileage, while bad enough before all this, has now dropped another 2 mpg to around 7.5 to 8. I was thinking about taking it to a Ford dealer for some kind of analysis.
I have a 05 f250 with a 5.4 I'm having issues with I was driving along the truck started chugging along and the check engine light came on so I checked it with my bully dog the codes that came up were p0192 which is fuel pressure sensor circuit low the next one is p0452 is evaporative emission pressure sensor switch low also came up with p0191 tonight haven't dug into that yet.
I change out the pressure sensor switch from a buddies truck didn't make a difference put my sensor in his truck his worked fine I clean the throttle position sensor and The maf also put a new air filter on not throwing a misfire code but seems like it may be. A little background on the truck it's a 5.4 3valve with a bully dog tuner, mufflers been removed added straight pipe mechanically that's all that's done
A few months ago I had a battery go bad. When I started the 2004 F250 6.0 it barely started. After that my transmission gauge became the engine coolant gauge and the engine coolant gauge became the transmission gauge. I tried disconnecting batteries but that did not work. I have the Scan Gauge tool and confirm the gauges are reading correctly but just swapped. So I'm wondering if the is a reset procedure for instrument panel.
View 7 RepliesSo I was driving my 2004 6.0 auto on the freeway today when the tow haul light randomly started flashing, nothing felt wrong until I stopped, then when I went to pull away it wouldn't shift down from 5th according to my livewire ts says under the commanded gear gauge. It shifts into 6 and overdrive fine. I turned the truck off, the light went off but as soon as I put it in drive it jumped around from 1-2-5 and back down until it locked in 5 again and the light started flashing again. What this could be?
View 1 Replies2006 F250 Diesel 125000. Got truck back from dealer pulling out noticed blinkers blinking fast. Figure classic burnt bulb. But upon further inspection no tail lights when headlights on. Ooh and a driver side mirror with blinker that has a crack over the lower light which is side the marker/running light, the light does work. After I Google the issue and see that the MFS is a big culprit I replaced it and have same issue. What I do have working and when:
Brake lights work when headlights off - no key in ignition
Brake lights work when headlights on with blinker on - no key in ignition
Brake lights do not work with headlights on - koeo, koer
Blinkers (rear) when selected both blink
Ignition switch?
2004 F250 v10 xtl 260xxx. Started off by using my remote start, truck started up ran for about 5 sec then shut off, then restart itself and shut back off. When I manually started it, it ran fine. I noticed my battery light was on and as I was driving it would flicker. First thing I did when I got home was clean all my connections to see if that worked. Battery light still on, checked my volts on my battery and they were at about 11.8 with a slow but steady drop while truck was idling.then checked my alt, that too was at about 11.9 with a stead drop.
Alt was only about 7 months old and I had a warranty on it so I had it replaced at Napa and had them test it there. Good alt. Installed the new alt charged up my battery and turned it over. Battery light still on and flickering. Checked all my wires for corrosion, checked all my grounds. Everything checked out. Checked my battery again 12.4 with the truck off, cranked it over and it was back at 11.9 with a steady drop and almost the same reading with the alt. I replaced the battery as well yesterday, seeing how it was about 7 years old.
I was driving and all of a sudden the radio died, battery light came on, Power windows and interior lights died, gauges died speedometer went all the way up to 100. The Head lights, turn signals and heater work. When I got home I opened the hood and the battery was boiling.
View 14 RepliesThe light on dash for 4X4 stays on no mater where the switch is placed I have it in 2 wd and it stays on. Where I need to start looking.
View 4 RepliesI have an 04 F250 4x4 king ranch with a 6.8 V10.
When I first bought this truck it had a problem of stalling out at stops. You could sometimes hold the brake and gas and push your way through it but it would sputter for a second and try to die and then it was fine once you got going. The OD light would flash, check engine light would come on and it would throw a P0720 code for the OSS. I did some researching and I pulled the sensor in the pumpkin before that because I read that could cause the same problem, so I cleaned it and put it back but it didn't solve the issue. Then found that an K&N air filter can often times clog the MAF and cause the issue so I pulled my air filter and sure enough it was a K&N, I swapped it with a normal filter and sprayed some MAF cleaner and its been running like a top for months... until now.
It started again, gradually at first. It would die when I started to back the truck at a very low speed to load my 4 wheeler. I fired it up and it was good again for a couple more weeks, then I went to hook to a horse trailer and I was having to back up a hill to get to it, and it just kept dying, OD light would flash, check engine light came on. I was in a bind so I just tried wiping off the MAF with a rag, that didn't work, my girlfriend was using the truck and said it kept dying whenever she stopped. I got it home and cleaned the MAF with cleaner really well but the problem persisted. I went ahead and changed my oil, spark plugs(gaped at .052-.054), replaced the IAC(which looked like it had been installed once before so I am guessing someone tried it and when it didn't fix the problem they returned it) and changed the fuel filter. I drove it around and it ran fine, drove it to work and it ran fine, my girlfriend took it for about 15 minutes to run an errand for me and it was fine until she got back in the parking lot and liked to never got it parked again it stalled so much.
So I went back to the drawing board and read that it is rarely the OSS that is the problem but that often times the issue is a bad coil pack. I don't have a scanner nor do I know how the heck to use one. I plan on going out of town at the end of the week and the truck has 194k miles on it so rather then take it to a shop and try to find out which COP was bad I just decided to replace all of them(I know, I know, you should never just start replacing parts). I only had time to replace 5 of them, I took the truck out and again it dove fine for an hour, went through traffic OK. It sat for an hour and when I left it started to die again, I could drop it in neutral and it would fire back up and as long as I gave it just a hair of throttle it stayed running fine, take my foot off the fuel and in a minute it would die again. After I drove for a bit it was fine again. Now I know the problem may yet be in the remaining 5 COP that I must change tonight but in case it is not I wanted to get input on this.
I've read the problem can come from a bad ground, so I took every ground point that I could find under the hood and I cleaned the connectors and took the paint off at the connection site just for good measure. The problem persists. I've read that sometimes a diode can go out on the alternator and cause this problem, I did use my amp meter and I'm checking out at 13 volts while running. I'm not the best with meters so I'm not sure how else to check the diode?
I've also read that taking it to a dealership is hit or miss for them diagnosing the problem, sometimes they find the issue, sometimes they just change the OSS. The only mechanic I trust closed his shop and is now service manager of the Dodge dealership. I'm thinking since this seems to be a common problem that maybe ford might have more knowledge of it then dodge but I trust the dodge dealership more because of who is over it. Either way I know it will sit in a dealership for awhile before it ever gets looked at and if they have to chase any electrical problems then that starts racking up $$ fast.
So what am I missing? I've thought about replacing the MAF since cleaning it the first time solved the problem. When it did this the first time I still had my 01 F250(it never gave me problems like this) and so I took the MAF off of it and swapped them and sure enough it fixed my problem so I switched them back after I cleaned the MAF and like I said it's been running fine until recently. I'd rather not throw money at this by replacing parts and hoping for the best. I've also read about tracing the harness that runs from the sensor on the pumpkin to the OSS and on. That harness runs through all kinds of stuff so I'm dreading that but it will also be a next step. I haven't pulled the OSS because its in a very awkward position on my truck.
I've got an '04 F250 4x4 gasser with a 4R100 tranny. I was driving home from work earlier when I noticed the overdrive lockout light was on. Not flashing, but steady like I'd accidentally locked out the O/D. I pressed the button to turn it off, but it stayed on and the O/D locked out for real. WTF?......I pressed it again, the light stayed on, but the trans shifted back to 4th like it's supposed to. I was near freeway speed, so I kept an eye on the tach for a few miles. Everything looked normal, except maybe the converter lockup seemed a bit sloppy whenever it downshifted/upshifted on a hill. That could be my imagination, though. I was in full AWACS mode by then, watching everything like a hawk.
Then I started wiggling the shifter a bit. I pushed the lever down against the detent, and the light went off. I let it go and it came back on. I did this a few times with the same results. It didn't affect the tranny operation. I pulled the lever back toward me like I was going to shift, and the light went out. I let it go and the light came back on. By this point I think I can rule out any major tranny problems as it seems the problem is in the wiring to the light, not to the O/D lockout circuit itself. I was thinking maybe a short to ground somewhere. What controls the lockout light, never had to deal with one before. I'm hoping for a easy answer before I tear into the steering column and start poking around in the harness.
My 1999 f250 superduty with the 5.4 was sitting in front of my house, and started all by itseft, did not have keys in it either and the doors were locked. I ran out thinking someone was stealing it but nope,? As far as I know it does not have a remote start either,i have owned it for the last two years and it has never happened before. It is a lariant edition also .
View 14 RepliesMy 1999 F250 V10 has started to lose power off and on. It will run fine then when I stop at a light or sign, then when I take off it runs like I pulling something heavy. If I stop again it goes back to normal sometimes. 161000 miles. No check engine light is on. Motor idles perfect and sounds great. I don't know anything about motors...
View 4 RepliesI have a ford f250 with a 5.4l 2v engine and lately it started to shake when it idles. i have changed all the ignition coils and spark plugs, the injector are fine, but i cant seem to pinpoint the problem. the weird thing is that there are no codes. the fuel trim on bank 1 is around -8 and bank 2 is at almost positive 20 and higher.
View 14 RepliesTruck : 2000 F250 XLT A/T 6.8L v10 4x4
Issue : O/D off light is flashing on the shift lever. In a drive gear (R, OD, D2, D1) there is very low power when giving it gas, more so from a stop. In P and N, I can rev the motor with no obvious issues. In O/D, I can't even get forward momentum going from a stop when on a slight incline. When on flat ground and in O/D, flooring the gas only gets me going a few MPH and RPMs don't go above 1500ish. When selecting 1st or 2nd, the truck still struggles a bit from a stop but does get up and going.
What happened leading up to the issue : I was on the freeway driving about 80MPH without cruise control se,t and with O/D on as usual, when the blinking O/D off light caught my attention. Not knowing at the time that this was a transmission problem light, I started pushing and holding on the O/D on/off button to try and get it to stop. Probably about a minute later, I realized I was losing speed even when giving more throttle so pulled over to the shoulder. I shut the truck off and restarted it, noted the Service Engine Soon light was now on, then I put it in O/D and gave it gas but only got going a couple MPH which it sounds like the engine was choking/struggling. I then tried D1 and D2 and, while still struggling a bit from stop, was able to accelerate up to 35+ MPH.
OBDII Codes:
P0743
Torque Converter
Clutch Solenoid
Circuit Electrical
P0750
Shift Solenoid A
P0755
Shift Solenoid B
P1747
Pressure Control
Solenoid A Short Circuit
P0443
EvaPorative Emission
System Purge Control
Valve Circuit
P0135
O2 Heater Circuit
(Bank 1. Sensor 1)
P0155
O2 Heater Circuit
(Bank 2. Sensor 1)
Troubleshooting : Transmission fluid check looks good (full and red)
Checked fuse 23 of the Central Junction Box
Held a ground wire to bottom of Transmission pan and to the frame while I started the truck, O/D light still flashing
Wiring looks good coming to the plug on the driver side of the transmission
More info:
- No "Service Engine Soon" or blinking O/D off light prior to all this happening.
- I don't believe I'm getting 1st gear. I don't recall if I got my speed up to 30+ MPH while in D1, but while in D2 I never noticed a shift from stop to ~35MPH. At 35MPH, my RPMs were around 2500 I believe.
- While cruising at 35MPH in D2, shifting to O/D results in lost power. I had to stay in D2 all the way home.
To do (I believe):
1. Check shift solenoids (looking for DIY info)
2. Check shift solenoid pack (looking for DIY info)
3. Check TCC solenoid (looking for for DIY info)
It sounds like there are a couple shift solenoids to check as well as a solenoid pack (how best to check these out, I'm still looking for)?