I bought a 2004 F250 Crew Cab LB 4x4 with the 5.4 Motor and when I turn left it has some Tight Spots and I can't figure out why, I checked the Drive axles to make sure the locking hubs were unlocked and they spun freely, I Also have a lot of play in the steering wheel, Could this all be Related to the Steering Box? What else should I check for ?
View 3 RepliesI had some steering issues with my truck so took it for an evaluation at pep boys. They recommended a new steering gear box and tie rod that hooks to the pitman arm so I had them replace them. Steering was improved but now the wheel is canted to the left or right depending on when I make a turn. When I make a left turn, the wheel is canted about 10 o'clock. When I make a right turn, it's canted about 1 o'clock.
I looked under and had my brother turn the wheel and didn't really notice any thing loose. I lifted the front and noticed the left wheel bearings need to be replaced. I also noticed the shocks were shot and replaced them but it didn't make a difference in the crooked wheel.
Do you think it's the wheel bearing that can cause this? How about the ball joints? The truck has 407k miles and I bought it a month ago. Previous owner said he never replaced any steering components. Should I just replace all steering components with the Moog kit? I'd like to hold off on the $600+ kit for now as I just bought a a boat and the boat needs some stuff. I hope to find that one thing (hopefully not more) that's loose.
2007 F250 SD Crew Cab Long Bed 4X4 with 6.0. Bulletproofed, leveling springs, 5k firestone airbags, upgraded brakes, new front driveshaft and new universals and carrier bearing on rear u joint.
The issue: When accelerating from a stop or a slow rolling start, turning right or left, I get a shimmy (vibration) that seems to be coming from under my feet. Not a violent shimmy, but enough to make me certain that something is loose or out of alignment in the drivetrain. IT IS NOT THE REAR END as friends have constantly told me. Rear end was serviced and cluth packs lubricated with no change in issue.
What I've done: Changed transfer case fluid, new front driveshaft, new u joints and carrier bearing on rear driveshaft. There has been no improvement after these repairs, if anything the vibration is a little worse and easier to induce.
I've been chasing this problem for over a year. Going to be pulling a Toy Hauler out west this falls and really need to repair this for my piece of mind..
I have a 2002 F250 diesel, the key will turn to acc. but not on. It feels like it is hitting something in the column. I tried moving the shifting lever back and forth with my foot on the break, as I turned the key but it would not turn. I am thinking the tumblers are OK because it goes into acc. It feels like their is some lever that is not releasing the shift lever, because if I turn the key hard the shift lever jumps. What is wrong, or how the interface between the lock tumbler and the shift lever works?
View 4 RepliesI have a 2008 F-450 Lariat 6.4 4x4. I recently started noticing the front driver side wheel (best I can tell) wheel makes a noise as though it's binding uo when turning either direction, and I can feel it as well. 4wd is not activated and the hubs are in auto. When the front end is off the ground, I rotated the wheels and they spun independently unless the hubs were locked. I noticed what appear to be seals on both the driver and passenger side hanging loose (see pics). What this might be? I recently used the 4wd when we visited White Sands National Monument while pulling a 5th wheel RV.
View 9 RepliesMy 2005 has the ESOF system which has worked flawlessly. Recently I had upper and lower ball joints done and after that repair I had no auto locking hubs. ( independent shop messed up seal install ) they redid the job and it now seems like my front hubs are locking automatically because I am getting binding while turning. So this is the problem.. the front wheels do not "pull" only the rear wheels spin. If I manually lock the hubs I have 4x4 and can get out of being nearly stuck and everything works normally. What is wrong here? Does the shop need to redo the job again?
View 2 RepliesI replaced the steering gear box in my 06 F250 CCLB 6.8 over the weekend with a reman Cardone. The old gear box had what I can best describe as a chatter/binding if you rocked the wheel back and forth, that's gone now. I sucked out as much fluid as I could, then filled the reservoir several times while the fluid ran out, what came out was very cloudy and gritty, guessing the old box was chewing itself up.
Can't seem to find a straight answer - what fluid SHOULD this have in it?
Sounds like I should have used Mercon, looks like I grabbed Type F instead. Could that cause the steering effort to be extremely light? I mean like ridiculously light, tip of your pinkie barely touching and turning the wheel light?
I'm looking at a 2004 F250 XLT super cab 4x4 with a 5.4L with only 50k on the clock. It looks to be in great shape and drives good with only a few issues. Cruise doesn't work, it pulls to the left a little, and it has a slight roar coming from the left front wheel. Other than that it seems to be a nice truck. Its blue and grey two tone. Anything else I need to look at before pulling the handle on this one?
View 11 RepliesI've got an 04 f250 4x4 crew cab. I just replaced the upper and lower ball joints on both sides and also the drag link. My alignment was off from the bad ball joints so I had it aligned after I did all of this. Now the steering is really weird. Its like something is to tight. I can barely keep the truck straight because every time I barely move the wheel I seem to be going one way or another and getting it straight is nearly impossible to the point I look like a drunk driver. I can turn the wheel to go around a curve and let go of it and it will stay that way until I turn it back. It won't return itself. I'm kind of lost.
View 3 RepliesI have a loose, binding, metal on metal sound on my steering wheel shaft. I have removed the steering wheel, replaced the clockspring, because when I removed wheel clockspring was in pieces and I thought that might be the issue. Guess not, because I'm still having problem. Other than having to remove or replace the whole steering column...
View 2 RepliesI have a 2004 superduty 250 4x4 with the 6.0. I am having a violent shake in the steering wheel mostly and can feel it in throttle at about 45 to 60 and at 72 there is s growel. Have changed tires, wheels checked all ball joints tie rods wheel bearings ujoints. Don't matter brakes on or off, od on or off nothing changes it. I really don't know what else to check.
View 10 Replies2004 F250 SuperDuty 6.0L Diesel. The turn signal (left or right), it would make a buzzing noise, so I located the relay under the steering wheel (by putting my hand on it and seeing which one was buzzing) and replaced it, I bought a replacement at Schucks, then the buzzing noise went away, and the clicking noise is back.
But.... I don't see the turn signal lights in the dashboard and the turn lights are not working, I checked, what could be the problem ? I read the owners manual, in the fuse box under the steering wheel, fuze #18 is used for turn lights, but it is not blown.
I have a 2004 F250 with 5.4 Triton engine. It stalls when tapping on Power steering reservoir! This is the oddest thing I've ever seen! I did not get time to look into it today but will sure do so tomorrow.
View 2 RepliesI have a 01 Chrysler Sebring 4D Sedan. I have been working on cars many years, never done tie rods. This my first attempt, I messed something up I believe. I replaced both inner tie rods and outer ends. I followed what I thought was correct procedure., counted turns on ends coming off. Installed new ones the same amount of turns. Before I did this the steering was fine. Now when I turn sharp to the right or left, like turning in to a driveway, I get an awful binding grinding noise, and I can feel it shimmy in the wheel. It will even stop the car going hard right. I can see evidence of rubbing on the CV boot closest to the wheel on the pass side. I assume I messed up somewhere with setting the steering when I installed the Tie rod ends to the wheel hubs.
View 19 RepliesLast couple drives I have noticed some front end noise on the left side. Back in May I also noticed grease all over behind the rotor. I believe this is the grease inserted via ABS hole into the unit bearing. I do not hear the needle bearing crunching while driving and did not here it in May either. I also attempted to move the unit-bearing up and down thinking the axle seal was toast but it seemed solid at the time.
Today I hear some noise while turning left which lead to the pictures below. Wet side is Driver side, dry side is passenger. Tomorrow morning I should have some time to take a look at this more in depth. Passenger needle bearing was changed last year and no issues since then......
I have a 2000 F-350,7.3, 6 speed. Just the other day I made a turn and my passenger got her feet wet. It had been raining and I also had the ac on. A couple of days later the same thing happened, but it had not rained, just the ac on. What is causing this. I do see condensate discharging under the truck.
View 7 RepliesAn odd noise just started recently where as I'm turning left, a popping noise happens seemingly right under my feet. I don't have a video, but I can probably try to take one later. It sounds like something is loose and when the weight shifts off of the left side of the truck, something is shifting and groaning.
I lifted the truck up yesterday and there is no play in the ball joints, wheel bearings, sway bar/end links, or tie rod ends. There is no play in the shock or in the spring, nor is there any movement in the radius arm or where the axle mounts to the body.
I should probably add some info on the truck. '00 V10 CCSB 2wd. I can't see anything out of the ordinary, and can't reproduce the sound unless the truck is in motion.
My dually has started to make a rubbing or grinding noise just about every time I make a turn, left or right. What this could be, truck has 8500 miles on it.
SD Dually
Ok i have a 99 f250 with a 6.8 v10 that is not turning over at all. I have checked the battery and its good. I have replaced the starter and the starter relay and have tested the starter and its good too. I have also used a volt meter on the batter, starter, and relay and looked at the relevant info and they are all in the correct volt range. I have also taken the starter off and looked at the flywheel and it has good teeth so thats not an issue. I am completely stumped now as to what it could be?
View 5 Replies'08 F350 6.4l 4wd, I had the truck come in with a exploded transfer case. (See pics). Ive read all about this happening to many others. The truck still drove, hubs not locked, plenty of fluid in the TC, pretty sure it was the double Cardan that did it. Anyways I replaced thwith TC, replaced the front driveshaft, filled the TC with recommended fluid. Test drove and drives great, shifts fine. Only until I turned left.
At slow speeds turning hard or 15-20 taking a turn, it sounds like a ratchet clicking from somewhere on the left side, right around the drivers door, from what I can hear from the cab. Does it in 2wd, 4wd hi/low, hubs locked or not. I changed the vacuum pump, no leaks, changed the IWE solenoid, pulled out both locking mechanisms, tightened crossmember, checked everything from the hours of research I did on the internet. I cannot find the problem. I don't know what else to check. Front axles free spin and lock when they are supposed to. I'm at the end...
First off my trucks a 2000 v10 f250 with four-wheel drive and 2 wheel abs with about 230000 miles on it.
I Recently replaced my unit bearing on my drivers side because I thought it was the cause of a grinding that only happens on hard left turns but I wasnt the cause it was going bad causing play in the half shaft. I didnt seem to notice and wear on the shaft from bad needle bearings but I have to take it all apart again to be sure. Was just wondering what else could be the cause of this noise. I plan to pull the axel shaft and change all the seals.