I'm wanting to grease the center spline on my drive shaft. I got the 4 bolts off with a 12mm 16 point boxed in wrench but can't get the drive shaft loose from the rea rend. I don't blindly want to go beating it out of the yoke with a hammer to try to knock it loose (but I will if I have to). What am I missing to get this shaft out?
View 3 RepliesMy elderly neighbor has asked me to re-attach his drive shaft on his F250.
Said his wife was driving and it broke the u joint or something, and he has gotten it repaired and wondered if I could put it back on. Has been sitting for a bit from what he said.
Just need to know, how I should clean up and or grease? the end with the boot on it. before I put it together. The boot looks to be zap strapped, is that standard?
I have a 2014 4WD Super Duty. It has a squeak that is coming from the drive shaft area. I had someone listen to it as I drove slowly next to them. It is a repetitive: squeak squeak squeak squeak squeak. Not loud. The frequency increases as speed increases. I could believe it may be a U joint based on the frequency, but seems hard to believe with a new truck. I heard this sound when I first got it, but the sound was so slight that I thought it was just some sound associated with a newer engine. But now it is becoming a bit louder.
View 4 RepliesI have a 2004 F350 with a broken drive shaft.
Got the original shaft off and it has the following part number (2C34-4K145-DNA)
but I've since learned that the part number has changed but the only info I could get was 2???. 4R602DQA.
Trying to find the part number so I can find it under 750.00 from the dealer
I have a 2004 F350 Crew Cab DRW 4WD 6.0L.
The front drive shaft is making a high pitched metallic squeal while the truck is in motion. I thought it might be the universal joints but after lubricating the joints, I can still hear the squeal and it sounds like it is coming from inside the drive shaft. I also hear this squeal when I spin the drive shaft by hand.
I have quite a few questions about these drive shafts:
- What would cause a squeal from within the drive shaft?
- Are there any replaceable parts or do I have to get a new drive shaft?
- How do I identify the correct drive shaft part for my truck? Seems like there are a LOT of different models on the web.
- Are any of the aftermarket drive shafts any good? Any to avoid?
- Is this a DIY job or will I need to take it in to the shop?
I have a 1999 Ford F250 super duty 4wheel drive, lifted (really a leveling kit but had to lift rear to compensate), 5.4l. Im having a problem with my front shaft turning while in 2 wheel drive. Hubs aren't locked and its in 2 wheel not 4. I've taken hubs off and the bearing spins free soo I know its in auto. Why is the drive shaft still turning???????
View 5 RepliesI tried searching and googling but came to no results, unless its like similar trucks. How do the 4x4 shift remove? I have an 04 F250 and someone decided to put the shift on sideways so the 4HI and etc read upside down before I purchased the truck. Do I just rip the thing off?
View 1 RepliesI am wanting to take off the center console lid to recover it. The only way I see to remove just the lid from the truck is to hit the rod out that is in the hinge. I was hitting pretty hard with a punch and it wasn't moving. I don't really want to break it so I'm asking if there is a different way or if I just need to use more force?!
View 4 RepliesI have a E99 F350 7.3L 4x4 I know some or most of you have already probably replaced this part and or pulled a front axle shaft out. So here is my question...In the pictures provided you can see what I think everyone is calling a "Dust Seal" and as you can see it is bad and making a very terrible noise when i hit a bump...I was wondering what parts I would need to replace this seal? I tried looking it up and just get lost in all of the other things....I have found write-ups for the axle being removed while changing ball joints but none by it self to just replace this seal.
[URL] ....
I am replacing the ball joints on my 07 f250 4x4. got down to the removal of the shaft itself and it won't budge. What is the secret here. Have to go to work on monday, and the weather in Cleveland isn't going to be very good on Sunday.
View 10 RepliesNot sure what caused it to break but my front driveshaft split in half. I had it in 4wd and was doing a K turn to back in my driveway in a snow storm.
I got underneath in the snow (miserable) and wasn't able to come close to getting it off. The bolts holding the shaft onto the t-case will not budge and the tiny 5/16" bolts stripped all my small 1/4" sockets. I'm guessing I need a 3/8" drive 5/16" for front and the rear just spins. Any tricks to getting this off the truck.
I'm trying to remove the center console from my 2016 f350 lariat cc. I have both drivers and passengers seats out and all the obvious bolts removed. I'm still not able to remove the console. I know I'm likely missing just a few bolts as its really loose.
View 8 RepliesI finally got my lift installed the other day from PMF. My question is how do I get my pinion angle corrected on the front drive shaft? I know Trevor sells a Tcase clocking adapter may have to go that route IDK Unlike the rear there's only so much pitch you can put on the front axle until it causes issues with steering. I was thinking of going with an aftermarket front drive shaft designed to handle harsher angles.
I live in the mountains and after installing the lift and pulling a trailer on some of theses steeper gravel roads I can feel a harshness or something coming from under to front of the truck. I'm unable to post pics since I'm back on the road but I can visually see the front drive shaft angle is definitely not in line like it was.
I'm currently running PMF 2.5 alpha with a 1'' spacer and 3 link kit up front and 5'' progressive leafs and traction bars out back. I was able to fix my rear shaft angle using shims on my carrier bearing ( not really a big fan having 1 1/2'' of stacked shims BTW ) ....
I have a vibration starting at 60mph. Its slight but there. I crawled under and found a very shiny rectangle of metal. Safe to assume I flung a shaft weight? It drives perfect around town just at freeway speeds.
View 14 RepliesAfter installing the lift on my 6.2 F250 I ran into the well known issue where the front drive shaft hits the catalytic converter. The two options I was told that I had was to weld in a slight jog into the exhaust guts to go around the cat or to get a smaller diameter drive shaft... I had the truck down at my local exhaust shop to have a new cat back system installed and I had the exhaust guy throw in his .02 about what to do.
He came up with a super easy/obvious fix. When the left and right exhaust meet up before the collector there is a welded brace that secures both sides together. He cut about .5" out of it and loosened the flanges and shifted the exhaust over. Welded the brace back up... Works perfect.
I have a 2004 F250 Lariat Crew Cab FX4 6-3/4' bed.
What is the procedure to remove the Driver's side Rear Sway Bar Link upper bolt? - the link attaches to the frame. The nut is on the inside of the frame with about 1/3" to 2/3" clearance between the frame and the fuel tank. Of course, the frame's "C" shape faces towards the inside.
I want to install a new front drive shaft in my 2000 F350. I have the new one, and it has a big nut and it is threaded for length adjustment. My old one has a rubber boot which is missing from the new one. I plan on using red locktite but I do not know the torque specs on the front universal caps. Should I take it to my mechanic? I've never owned a 4x4 before.
View 3 RepliesI have a 1999 F-250 super duty 7.3 4x4 and the rear drivers side axle seal is leaking. My question is how do I remove the axle shaft? my last truck a f150 had c clips in the diff that released the axle shaft but I did not see those on this truck. How to remove the axle shaft?
View 8 Replies2003 f350 6.0 diesel, driving on the freeway at 70 mph, all instrumentation went off, the radio went off, the engine was still running fine. While pulling off on the off ramp, when the speed was about 20 mph the rear end jumped up as if the transmission was trying to go into reverse. After traveling about 4 miles at about 15 mph the rear end jumped up about 6 inches and the drive shaft pulled out of the spline and drove itself into the pavement. Why this happened. I have put two new batteries and an alternator in the truck and it has been fine every since, but I am still concerned it may happen again. The truck has a 6 inch lift on it.
View 3 RepliesCheck out the pics. 99 f250 4x4. I have a leak in my front axle shaft. It looks like it is coming out of the dust cap on the end of the front shaft. I am pretty sure it is differential fluid from the smell. Is there a seal before the dust cap? Is the shaft hollow with fluid in it? I thought it was just in the differential and if it leaks it is at the seals where the axle goes into the differential not at the otter end.
View 14 RepliesI have a ford f250 super duty and it wont start I have checked obvious reasons and I think it might be a crank shaft sensor. Just curious, is there two of them one for right bank and left bank or just one on drivers side?
View 2 Replies