Ford Super Duty (1999-2016) :: 2004 F250 - Clunk In Reverse When Clutch Is Pressed
Jun 1, 2013
My issue, just purchased f250, 2004, v 10, manual transmission, state vehicle with 32,000 miles but was a plow vehicle for localRMV lot, that said, great shape and runs strong but I get a clunk and shutter when I am in reverse and only when I push down clutch before stopping. Doesn't do it starting forward or reverse, only reverse and when I push clutch in before stopping. Did have a friend drive and looks like the transfer case is moving, as if mounts or bolts are loose. Does this make sense and could bad slip joints be putting excess torque on ?!?!?
View 4 Replies
Advertisement
Ive got a 04 f350 that after u shift into 4hi or 4lo when u accelerate it it makes loud clunk noise in fwd or reverse hi or lo. With hubs unlocked it still clunks. Have checked, wheel bearings, axle U-joints, and driveshaft joints all good. So I am thinking I've got issues in t-case. Popped drain plug out and wow that dex merc 4 looks nasty. So thinking I need exploded view of transfer case.
View 4 Replies
Had a No start issue.Turn the key and nothing. Could hear the relays click so knew it wasn't the ignition. Could jump the starter via the wire on the passenger fender so starter good. Replaced the clutch position switch last night. Still have no start but now when I press clutch I have a tow haul light come on dash.If I press it again it turns off. Truck doesn't have tow haul option installed. I hear a relay clicking under the dash too. This is a 2004 Superduty (F550). Replaced the ignition switch today and still same.
View 3 Replies
I'm having issue with my brake lights. Checked for voltage and nothing. Checked the fuses under the dash. Checked the brake pedal switch and have power going out when the pedal is pressed. Is there a relay or something somewhere else? 1999 f250 7.3 superduty....
View 2 Replies
On a cold crank the engine idles rough until it warms or the accelerator is pressed down. Also runs rough going up hills or towing. Check engine light is on and is throwing the code for bank 1 to lean and cat performance below threshold. Cats have been tested, good. Fuel trim tested, good. One mechanic said noth8ng is wrong with it well, there is. 2011 f250 6.2 gas...
View 5 Replies
New truck 11000kms ago thats done medium amount of work but nothing heavy or sustained for long periods of time. I get the feeling of clutches slipping especially when truck is cold but also when normal temps. Doesnt make any weird noises or anything. I can really notice the difference in torque if in manual mode being much better, but still not perfect if i stomp on the gas pedal and go through the gears in manual mode will still slip. Also is really harsh shift if i come to a halt in 3rd manual mode with the brake pedal depressed push minus button the truck makes very loud clunk noise into gear 2 then 1. Took it to ford they couldnt find anything ? Thinking of trying another dealer.
View 2 Replies
Just moved into the 250 from years of 150's. Now have 98 miles and read that the tran would have noise but normal while breaking in.
whats normal, not used to this much Clunk while changing from P to D ect. More noise than used too I guess.
3.73 gears
2014 F250, 6.2 gas 2wd....
View 8 Replies
I have a 2004 f250 with some front end troubles. When turning right once in a while it will make a hard CLUNK noise and then trying to drive down the street it drifts over to the left and I pull the wheel back to the right and when I turn the wheel it feels like I like theres something hitting somthing else in the front end. I have checked ball joints and tie rods and they are all nice and tight. Some stuff I have done that probably isn't related to my problem is shocks and sway bar end links. What this could be? Hopefully not the steering box!
View 7 Replies
I continuously read that people with 6.2 F250s averaging 13 mpg or so in a combination city/highway driving. This 2014 4x4 barely has enough power to move itself (honestly, I'd rather have my Ram 1500 back) and barely gets 10mpg. Basically have to give it about half-pedal to even get up to freeway speed and floor it if i want to pass anything. Is it just that much of a POS or does this not sound right? Other than a massive "clunk" sound when shifting from reverse to drive or vice versa, no indication of any problems.
View 14 Replies
Have an 06 F250. When I slow down to make a turn then accelerate it's like the drive shaft spins half a turn before it catches. Been doing it for awhile now. Now I'm get a clunk when I come to a complete stop. When you stop then truck settles there is a little clunk. Does this sound like the slip yoke problem?
View 1 Replies
I have a 2005 f250 that has a wander and a clunk what feels like under the drivers seat. The driver side bushing in the radius arm has no dirt and looks like wear on it compared to the passenger side which is completely covered in dirt. My question is, bushing wear out will cause wander and a clunk. Is it hard to replace?
View 3 Replies
When I go over good size bumps, I hear a clunk in the front tire area when my driver's window is down. It's a metal noise, like something loose.
2011 F-250 with 203K miles. Replaced shocks last year. Did this with stock wheels/tires. Something in the front suspension or axles. What should I be looking at?
View 8 Replies
I Have a 1999 f250 7.3 diesel with the zf5 manual transmission and to shift gears I need to push the clutch all the way to the floor. Could this possibly be the slave and master cylinder or is it the clutch?
View 14 Replies
As the title says are my front leaf springs bad? I got this truck 2 years ago and replaced all the ball joints, shocks, sway bar links,front hubs, rotors and brakes along with all the seals. I have a clunk in the front and I can't figure out what it's coming from. Could my leaf springs be clacking together? Truck
is a 2000 F250 SD v10.....
Driverside front
Rear spring
View 10 Replies
My rear wheel bearing are a little loose. This afternoon while diagnosing a squeak in the back I found this. While pushing the truck side to side there is a clunk and when you lay your hand on the tire you can feel it, bearings are loose. Nothing during the operation of the truck to give this away, truck runs and drives as it should but I need to check it our before something does go wrong. What I'm looking for is a torque / preload that the rear wheel bearings need to be set at.
View 2 Replies
I have a 02 F250 4x4 5.4. As I drive and when pulling into a driveway I hear a clunk that can be felt in the floor and the steering wheel. I've replaced the wheel bearings and seals, shocks, ball joints, sway bar links and bushings, tie rod ends at the gear box and "right hand inner". The other two tie rods are tight and so is the track bar. I cannot duplicate the sound if I jack it up and move parts around with a pry bar. I can however move the steer box sector shaft upwards about an 1/8. I've adjusted the screw but it didn't do anything. Could it be the steer box or the springs? I've even mounted a GoPro underneath but everything moves and I can't tell why it is.
View 14 Replies
2007 F250 4WD 5.4l ... when I turn sharply in either direction I am getting a light clunk sound similar to when you are in 4WD on blacktop and try turning. The engine also seems to wanna stall when I cut the wheel too sharp.
View 4 Replies
2002, F250, 5.4L, ZF-6 trans.
Ok...today by accident turned the key with the truck in gear and clutch not depressed...much to my surprise the truck tried to start and lurched forward.
Is this a sign of a failing clutch safety switch or Could it be an ignition switch problem? Anything else that I am not thinking of?
View 5 Replies
I just bought my first Ford. Its a 2003 F250 SD with 5.4L, 5 speed manual, extended cab, 2WD. The truck is experiencing intermittent problems with the clutch pedal.
If I depress the clutch pedal for a long time, then sometimes it does not retract all the way. It does this, for example, when I am at a traffic light waiting for the next opportunity to make a left hand turn.
The truck runs and operates as it should even when this does happen. The easy response is to place your toes under the clutch pedal and pull it aft to its completely released position.
The master and slave cylinder and the booster spring attached to the clutch pedal assembly have been replaced and this condition still continues.
View 2 Replies
I have a 06 6.0 with 340000 miles on it believe it or not still pulls great. The problem is my clutch fan keeps roaring when I press the gas it's extremely loud all my gauges are fine so the truck isn't overheating? Also not a bad fan clutch I wasted 300 bucks on that and it's still doing the same thing.
View 6 Replies
I have a 99 f250 sd truck that came as a auto and I am changing it to manual. I bought a slave cylinder unit setup and got it put in and as I was installing rod from pedal to slave I must of broke plastic fingers that hold rod. So is them fingers replaceable or must I buy another unit? with no foot on pedal it sticks up close to bottom of dash now. I tried pushing clutch all the way to floor and still rises too high. What can I do????
View 1 Replies
