Ford Super Duty (1999-2016) :: 2004 F250 6.0 - Missing At Idle?
Mar 10, 2016
I have a 2004 F-250 with a 6.0 and a 6-speed with 140,000 miles. It has been studded, and has upgraded injectors. ( Not sure on the size, they bored them at at the diesel shop that studded my heads.) Also have an EGR delete, with the EGR turned off on the SCT as well. I also have a SCT Livewire set on the 65HP tow tune.
Truck has always ran great in the year and a half I have had it. I changed the oil three days ago, and now I am getting a miss at idle. The trucks cranks right up and drives normally. Once it is at operating temperature, when I stop at a light it has a very noticeable miss. There is no surging, or change in RPM's at all. Just seems like it is cutting out every few seconds. This is also somewhat intermittent. FICM shows 49 volts always, even when this is occurring.
Also, this may be unrelated, my oil temperature seems higher since the oil change. Was around 192 water/197 oil while cruising 70 on the interstate. Now, its' more like 192/202. I've always ran Motorcraft 15w-40, and that is what I used for this oil change as well.
I see some people have a similar problem, but all the posts I've read involved fluctuating RPM's or surging, or both. Other than this, the truck cranks and runs just like normal.
View 2 Replies
Advertisement
I have a 2007 F250 4X4 6.0 diesel. When first started it idles extremely rough to a point it sounds like a old gas engine missing. But after it warms up for about 15 minutes it runs and idles like a new truck. I'm thinking it's the injectors if so is this something I can change/clean ....
View 2 Replies
I have a 1999 F250 Super Duty 5.4L, 118,000miles...engine seems to idle somewhat rough but tach doesn't seem to move off 1000rpm & when giving slight acceleration seems to act like its missing, shaking . But under acceleration moderate or high purrs like a kitten! Always starts good , few cranks. Any hints on the what issue might be?
View 2 Replies
I have recently purchased an 04 F250 crew cab with the 6.0 power stroke, it has a cold air intake, 4inch exhaust from the turbo back and has a program in it but programmer didn't come with the truck. When I sit at a traffic light and go to leave on a green light the truck kind of hesitates or acts like it's missing out( maybe loading up) shoots out black smoke then runs fine, it doesn't do it at all the stop lights but does get irritating. If I get it flashed back to stock settings will the truck run normal with all the upgrades?
View 4 Replies
My v10 has a cold miss when i start it in the morning no matter what the temp. It misses until it gets up to operating temp.then it runs fine all day with a slight miss.
- Changed plugs,
- Changed pcv,
- Changed iacv,
- Cleaned map sensor,
- Changed tube to pcv,
No codes. Its running as if it had a carb and the choke is closed. No smoke, tach. idles between 750 down to about 500, until it warms up then tach. Stays steady.
View 4 Replies
I was washing my 2004 F-250 today and I looked down by the front passenger wheel well and I noticed a small chuck missing from the bottom of the frame. The other side in the same spot doesn't have it and at the spot in question, I noticed some sort of crack had been welded before. I never had any of that done to the truck. What about getting it fixed? get it fixed right away or keep an eye out for cracks. so far its just that hole and what looks like a welded crack above. everything else seems fine. I know a repair would be inexpensive and easy just to weld a steel or titanium plate on the spot.
View 11 Replies
I have a 2004 ford f250 5.4 and ithe makes a Humming noise only at idle. I have checked the fan clutch. it seems to be good and does not spin freely. I was thinking maybe idle air control valve but the truck idles like normal and does not stall. the sound does go away when squeezing the air hose doing today the IAC but comes back as soon as you let off. can it still be the idle air control valve if idles fine and doesn't stall?
View 5 Replies
I have a 1999 ford f250 with a 6.8 liter v 10 engine. At about 40mph the truck will start missing and lacks power to accelerate further. This problem is intermittent. Some days it runs great and others the miss appears. Well I scanned and the code reader said that I had a misfire on cylinder 7. I took a chance and replaced the COP and the boot for that cylinder . Ran great for a day and then the miss came back. Same code again. What else might cause this? Are plugs difficult to change in these engines?
View 6 Replies
Just got a 2008 F-250, truck has the center console jump seat and the console lid is missing. Can you just buy a new lid or do you have to buy the whole thing? Cost? Places to buy?
View 4 Replies
I have 2005 f250 5.4l 3v that was having miss problems between 1200 and 2000 RPMs. Changed VCT solenoids which worked, but then could hear chain hitting cover when powering down throttle on left side. Figured chain tensioner was bad, so tore down and removed timing cover. Found left chain was tighter than what seems normal, and right side had huge amount of slack. While taking off tensioner on left side, something happened to fast for me to see it, and still not sure if what happened wasn't just my imagination. I thought that the chain moved very fast for an inch or two. Anyways, I watched how to video on timing the 3v, but I am very confused about it. The left bank seems to line up on timing marks perfectly, but the right chain is off by at least 2 1/2 links. Not knowing any better, I removed three rockers on left bank (2 intakes and 1 exhaust) but only removed two intake rockers on right side. I don't know what I am doing and getting scared.
View 1 Replies
I bought a 99 f250 super duty with v-10. Ran great then I decided to hose off engine compartment. No pressure washer just running water trying to get all the dirt off now the engine sounds like its missing. Could I have a coil pack that got wet or is something else wrong.
View 3 Replies
So, I have a 2007 f250 with the 6.0. When she's cold she starts fine but runs rough like she has a miss. When she warms up the miss goes away and it runs pretty good. But if I shut it off it won't start for about an hour or so.
ICP sensor has been replaced.
FICM is putting out 50v
View 11 Replies
I have a 2008 f250 superduty with the v10. Just today I was driving and engine picked up.slight miss it's rainy. I thought coil pack, but it left me on side of road. Got fired limped home won't go more than 40mph. Runs rough, no power, checked codes and get P0340, p0357, p1336, and P2195.. Where to start.. My daily driver and have to get back on road.
View 1 Replies
I've got a 2006 F250 5.4l Super Cab. When I bought the truck the rear interior door trim panels were missing. I tried to order them straight from ford but it turns out they no longer carry them, and I can't seem to find them anywhere online. I've also looked at the salvage yards in my area- nothing. Where I would be able to find these elusive creatures?
View 3 Replies
My truck is a 2003 f250 / 2wd automatic, 7.3 powerstroke, 284000 well maintained miles.
Just last week I sprug a large oil leak and had to replace the hoop outlet o rings..problem solved. This week I can drive 15-20 miles on the freeway and the truck starts to act like ota running out of fuel. Bogs down to 40mph then starts missing. I pull over, and when revving I have un burnt fuel and oil smoking out of my tailpipe. I let it sit for 5-10 minutes and it will be fine for the rest of the drive and this happens intermittently, there is no pattern.
The truck has a ton of power, starts great hot or cold. I did a ton of research and found a IPR could possibly cause this, as could plugged screens in the fuel pickup. Then I read about all the injector harness issues but I don't think that I my issue.
View 8 Replies
I just had the bed and tailgate on my 2004 replaced with a 2015. The body shop took my old lock cylinder out to put in the new tailgate. The old tailgate is only a year old and I wanted to sell it. The issue is that the latch will not open the tailgate. I can manually unlatch it by pulling the rods. Does the lock cylinder not being installed somehow affect this and need to be installed for it to function properly or do the rods simply need to be adjusted?
View 4 Replies
I have a 2001 Ford F250 V10 with about 70,000 miles on it and now the gauge indicates low pressure when my warmed up truck idles around 1000 RPM.
I went off road the other day into some mud and since then I have had my oil pressure gauge reporting low at idle and normal when moving.
I was a quart and 1/2 low on oil which I filled and the next day I changed the oil. I then had taken it Ford shop who replaced the oil sensor and said all fixed. It wasn't and I took it back in ... now the mechanic indicated it is probably the crankshaft bearing based on his experience and I should replace the engine.
This seems drastic? Wouldnt' the next step to go check/replace the oil pump?
View 6 Replies
I have a 2000 F-250 V10 that misses (cylinder 10) at the idle, once you give it gas it runs correctly again. I am at a loss. I have replaced the plug, tried moving coils from one cylinder to another to see if it shifts the miss, and it has new injectors. What this could be?
View 9 Replies
I have a 99 f250 sd with v10 that has no power. Will crank, idle and die sometimes. Getting codes p0351 - p0355. No power when driving.
View 11 Replies
I recently purchased a 1999 6.8L. Runs great when cold but after warming up the idle gets rough. Truck has new plugs and coil packs and fuel filter. Checked the fuel pressure and the idle is right at 30 psi. I read that the good pressure range is 30 to 45 psi. Is 30 psi acceptable or should I replace fuel pump or regulator? Any next step to solving my idle woes.
View 3 Replies
Having problems with no heat at idle or low heat in the cab. I just bought this truck a couple weeks ago and have a limited warranty on it. The truck makes no heat at idle. I start it and let it just run, engine temp gauge goes up to normal operating temp in 15 min or so, still nothing from the vents but cold air. If I drive it I get a "little" heat, at idle, cold air again. I believe the thermostat is working because like I said, engine temp stays right in the middle.
Brought it to local ford dealer, their diagnosis was heat core clogged and needed to be flushed, had that done. truck has been running 40 minutes in the driveway now, engine temps nice and warm, no heat. What could be the issue? I took a picture of what I believe are the lines running to the heater core, just barely warm to the touch, not hot by any means. It looks like there is a vacuum actuator on the line running in but there is no hose attached to it, what this it, should it have a line running to it?
View 14 Replies
