Ford Super Duty (1999-2016) :: 2003 - Rubbing Noise While In Reverse?
Apr 30, 2017
I bought a nice 03 F250 V10 with apx 170k on Friday... After I got home (it was about a 4hr drive) I went to back up into the driveway and heard a loud (deep) rub noise.. Sounds like metal on metal... After a few feet or at a faster pace it goes away. I've tried seeing if it changed or went away depending on how the wheels were turned but it did not make a difference. At first I thought it was coming from the hub but now I'm thinking it could be driveshaft related..
View 6 Replies
Advertisement
I drive a 2014 F350 Platinum SRW. No matter how fast i go, there is always a rubbing noise & i can hear it right outside my front window. Its annoying & loud. The mechanics told me it was my dust seal on my front axle but they changed it & its making the same noise even worse than before.
View 1 Replies
My dually has started to make a rubbing or grinding noise just about every time I make a turn, left or right. What this could be, truck has 8500 miles on it.
SD Dually
View 9 Replies
I noticed yesterday that my tire on the driver's side has rubbed a flat spot on the rubber brake hose. I bent the metal tubing so that it doesn't rub any more, but should this be of great concern? Obviously I'd hate for it to rupture, but it looks as though it's not too bad.
View 1 Replies
I only hear it at low speeds, but I guess that's to be expected. I've heard a similar noise before with other cars/trucks, but I can't recall what causes it. Just looking on tips for where to start looking with the front end parts or wheel/caliper assembly.
Also, but not sure it's related, had a lot of front end wobble when I applied the brakes coming down steep hills last week while pulling a big, but empty, gooseneck trailer. I assumed warped rotors, but later, after I had picked up my load, it quit doing it, albeit I had started babying the brakes. Still, there was one instance of very hard braking and it didn't do it at all, but that was on straight pavement.
It's almost as if having that empty trailer and/or going down a steep hill caused it, and not anything on the truck. But the rubbing sound started before that wobbling. Whatcha think?
View 2 Replies
I got an 03 f250 with a 10 inch lift on 40x14.50 tires on 20x10 fuel hostage wheels. They rub my springs pretty bad when trying to make even the slightest kind of tight turn and the sound they make when they rub is even worse than them actually rubbing. My question is should i stay with this tire and wheel setup and try to get some 6061 billet aluminum 2 inch spacers? (I'm not sure about going that route though because of what i heard about spacers) or go down to some 38s with a 20x14 wheel that hopefully would push the tire away from the hub like spacers would do. I'm leaning more towards going to 38s because of the rubbing and also because I feel they might look better on the 10 inch lift rather than the 40s but dont know whats the best thing to do.
View 12 Replies
I have a really loud whining kind of noise found that its the wheel seal rubbing on the inner part of the wheel bearing. I was just curious if its safe to drive with the spindle removed from the axle?
View 5 Replies
Went for a drive today in my Wifes 2003 F-250 5.4 automatic, Parked it and went for a hike, came back, started the truck ,put the it in reverse and it was running real rough.Put it in Drive and still running rough, figured i would put the truck in low and see what happens.It ran fine.Got home and did a visual inspection on the tranny, didn't see anything that jumped out at me.The fluid was fine. What this might be?
View 13 Replies
I have a 2003 f350 4WD that studders or skips only when in reverse. I noticed it the other day while plowing. The noise seems to be coming from the transfer case but only in reverse. If I go real easy it won't happen but it will happen if I gas it a little. Happens both with hubs locked or unlocked. BTW it is a manual shift transfer case and manual hubs.
View 3 Replies
I have a 2015 F250 6.7L and I am having problems with the brakes. When you first start the truck and put it in reverse and hit the brakes there is a continuous popping noise coming from the floor board and it can be felt in the brake pedal. It feels like the brake pedal is kicking back, once you drive the truck a little ways down the road the brakes work fine but if you hit the brakes a few times in a row like coming to a red light the noise is there again and it can be felt in the pedal.
View 3 Replies
I remember seeing a post a while back stating that the reverse sensor would make a clicking noise (when you're ear is up against the sensor) when working properly, I only had one working but I figured I'd replace them all since the 4th one was sure to go out . Fast forward to using two different sets of sensors, and not a single has worked or made that clicking noise like I would assume it should be. Can an aftermarket head unit cause these sensors to not work properly or have I just gotten two bum sets?
View 3 Replies
Installing a back up camera and need to locate reverse lights on driver's side at rear bumper. What color wire is for the reverse lights on a 2003 F-350 (truck in my sig)?
View 4 Replies
Ive got a 04 f350 that after u shift into 4hi or 4lo when u accelerate it it makes loud clunk noise in fwd or reverse hi or lo. With hubs unlocked it still clunks. Have checked, wheel bearings, axle U-joints, and driveshaft joints all good. So I am thinking I've got issues in t-case. Popped drain plug out and wow that dex merc 4 looks nasty. So thinking I need exploded view of transfer case.
View 4 Replies
This is my dads f250 build date of 9/03. I know these wheels are not the factory xl wheels. I also think they changed something with the wheel back spacing somewhere around this time. He is running 285/70/17 bfgs and is rubbing the leaf springs pretty good. He ran this same size on his previous 02 model with no rubbing. Can he get away with 1/4 spacers? What years these wheels are from? And the backspacing differences, if any. His 02 had the chrome large bullet hole style wheels.
View 5 Replies
I had my leveling kit installed today. Bilstein 2" leveling coils, adjustable track bar, 4" rear blocks, and shocks front and rear.
I have 295/70/18 tires on stock wheels that didn't rub anywhere before. Now at full lock to the left the drivers side tire just barely rubs on the radius arm. How is that possible? I was planning on getting 35s soon when these wear out but it seems like those would rub even worse.
View 8 Replies
I have a 2011 6.7L F-250 with the stock 17" rims and need new tires. Would 285/75/17's will fit without modification or rubbing?
The stock tires were 265/70/17 and were too small. I have 285/65/18's on there now without rubbing, but it is close. Going back to the 17" rim with a taller tire makes me a little nervous, as I can't check them before purchasing.
I do not want to have any rubbing or have to do any modifications (lift, spacers, etc...). I would like to keep the vehicle stock.
View 4 Replies
I'm contemplating a 4" lift on my 2012 F250/6.2L. It sits at stock height now with 315/70R17, slight rubbing on the mud flaps near full lock.
View 8 Replies
Got some snow tonight and was driving home from work around 35-40 mph in 4x4. You can tell that everything is engaged by the feeling and noise. Just not sure if this is abnormal. When letting off the throttle there's an extra metallic rubbing sound that goes with the drivetrain speed. Not sure if I'm just hearing the driveshaft from being in 4x4 of if something is up?
View 14 Replies
I have a 2000 F-250 Crew Cab with Lariate Trim package (not sure how that could be relevant to the issue, but it might be?) and auto locking Hubs. Recently, the truck has taken to making an intermittent grinding/Rubbing sound that comes seems to come from the wheels. I can not locate the sound exactly since it only happens when I'm Driving, I have never heard the sound at any speed lower than 20 mph or when the 4x4 is engaged either manually through he hubs or the selector in the cab when the hubs are in auto. All this leads me to think that I need to replace the autolocking hubs, but i'd like a second opinion (or even third) before I go to the trouble of replacing them.
View 1 Replies
I have a 2001 f250 7.3 4x4 today I locked the hubs, put it in 4 low and got threw some mud to go hunting fine. got back out of the woods and took it out of 4x4 unlocked hubs and went in reverse 30 yards.. Now when i drive it makes a weird sound like a rubbing sound near the front axle. What this is?
View 5 Replies
1999 F350 4x4 dually. Replacing brakes front and back. Rotors, Pads, and hoses. On the left front put rotor back on and torqued down hub nuts on rotor. Then caliper mounting bracket wouldn't fit back between mounting bracket and rotor. Loosened the hub nuts on rotor, and fit mounting bracket in place. Then torqued down the hub nuts again, and rotor rubs on mounting bracket and rotor/hub won't turn.
View 2 Replies
