Ford Super Duty (1999-2016) :: 2003 - Rough Idle / Takes Longer To Crank
Apr 20, 2014
I just got an 03 6.0 and a few days ago it developed a rough idle, it takes a little longer to crank and idles fine for 30 seconds to a minute then the rough idle kicks in also I noticed when I drive it the low rpm range is a little choppy and when I come to a stop it goes a little below idle then resumes the rough idle issue. I had it die on the road a day prior to this after it lost complete power at a red light, it started to idle low so I tried to counteract with a little throttle and with the throttle all the way it did nothing, a few minutes it died on the road and took a few minutes to start back up I did a set of filters and it hasn't done it again but I still have the rough idle, I checked the icp sensor and wiring no oil so I cleaned it up a bit and it runs a little smoother.
View 2 Replies
Advertisement
I have a 2013 F250 with a 6.2L gas motor, 50k miles.
Recently, I've noticed it takes longer to start. The motor will crank at regular speed but will take longer to start. It's always taken longer than a single rotation from day one but lately it's gotten really bad.
Even more recently, I hear a ticking noise under load, or even sometimes at idle. It sounds like an exhaust leak or worn lifter noise. Could these somehow be connected? What this could be?
View 2 Replies
It used to be, if I remember correctly, that while turning the key on a cold start the oil pressure gauge needle would show pressure prior to the engine starting, now it takes longer to start and the needle doesn't move until after the motor has started. I had the O-ring kit replaced due to oil leakage, and I wonder if there is an issue with the system. N to watch as they deedo their cold start today...
View 4 Replies
I'm having a problem with my 04 f250 6.0. I replaced my brakes rotors and calipers yesterday along with my fuel filters and after I took out my air filter to check it and put it back in my truck will no longer crank. When I put my key in the on position all of my lights and dings happen but I don't hear my fuel pump and when I go to turn it over I get nothing at all.
View 8 Replies
I've got a 2003 6.0 that's got a rough idle and low power situation. Doesn't matter hot or cold it has a hard start issue but when it finally starts it has a rough idle, sometimes it has low power on take off but not always. FICM has 48.8 volts coming out, exhaust just had a new y-pipe (had a cracked bellow) absolutely no smoke coming out. When I drive it hard it's like a rocket no rough spots just did oil with filters and fuel filters, blue spring upgrade, and cleaned out the turbo.
View 2 Replies
Been driving my 2001 f250 7.3 4x4 with no problems then started noticing it lacking power so I changed fuel filter and air filter. After a week goes by I was at work and I was leaving to come home so I started truck to let warm up and it cranked longer than normal but started. Let run about 10 minutes idle nicely when I punched it it bogged down and had no power never died. I idled over into parking lot and power came so I took off again loss all power again, still never died. Got it right back to my work sat there a bit and tried again this time I took it easy and was able to get my truck home 30 so miles.
When I got home I ran codes p1211 came up for the icp sensor I changed it did not change anything still had same problem. This was a Saturday afternoon to evening issue. So sunday I played around with it just checking out info online and test driving it seem to run ok but still lacking power. Let it sit till Monday I went out to start it had to cycle key 3 time before it started idle nicely then died would not restart changed ipr valve nothing changed cam sensor nothing changed some how 10 quarts low in oil just changed dec. 30th don't know ? Now will start if I pump throttle and has all its power back?
View 1 Replies
The 2003 F250 5.4 Superduty has no power and keeps stalling. If I floor the gas it just stalls. I've replaced the pcv valve and line, the fuel pump relay, the fuel pump, and cleaned the tank, changed out the gas, added Lucas, and it just won't run right. Desperate, and no codes are coming up...
View 5 Replies
I have a 99 f250 sd with v10 that has no power. Will crank, idle and die sometimes. Getting codes p0351 - p0355. No power when driving.
View 11 Replies
My F53 motorhome has a rough idle and hard misfire but is not setting any codes. I've put new plugs in it and not change.
View 7 Replies
I have a 2000 F250, SuperCab, 5.4 triton, 100,000 miles. It's been a great truck - got it at 63,000 miles. Once engine warms up, it has rough idle, and shift rough. I can give it gas to RPMs up and it smooths out some but is low on power. If this was my 76 F150, I would guess the vacuum hose off the intake manifold to the transmission came loose.
View 6 Replies
V-10 running rough at idle, chugging. a problem has developed with my 2004 E-350 V- 10 after having a new fuel filter installed and the induction service done . Picked it up from a local shop and it was running rough after bringing it in when running great! I figured maybe it fouled a plug or something so I drove it home but it didn't improve so I brought it back and had new plugs installed. It is still running rough and wanting to almost stall when accelerating from a stop and the shop cant figure it out , not showing any codes.
I'm thinking maybe they caused some type of vacuum leak that is so far undetected. The killer is it came to the shop running great !!
No other problems with the vehicle, I drive it every day and have owned since new. 278,000 on it now and it has been the best vehicle I have ever owned.
View 8 Replies
I recently purchased a 1999 6.8L. Runs great when cold but after warming up the idle gets rough. Truck has new plugs and coil packs and fuel filter. Checked the fuel pressure and the idle is right at 30 psi. I read that the good pressure range is 30 to 45 psi. Is 30 psi acceptable or should I replace fuel pump or regulator? Any next step to solving my idle woes.
View 3 Replies
Last night, I left it running while unloading a trailer and come back to notice it was idling abnormal. I jumped in it and tried to move it and there was a noticeable loss of power. I unhooked the trailer and tried to get it home. I only made it 1/2 mile down the road when it started spitting and sputtering (surging ever now and then) to a level that it died completely. I was able to start it back and get it out of the road but had to be pulled into a drive. It got to a point it wouldn't start back at all.
Today it started up however still had a rough idle and really has no power to speak of. The more I messed with it the less power it seem to have.
I have searched the forums and tried these things:
1) Checked the oil and noticed it was on the low end of the operating range. I put some in it to put it back to normal.
2) Disconnected the ICP
3) Changed the crankshaft position sensor
4) I dumped the fuel bowl after it completely died (in case it had any water in the fuel bowl).
The fuel filter was just changed 2 weeks ago. The fuel pump seems to be operating correctly (or it at least refilled the bowl) and started again with a very rough idle.
It doesn't have a engine light on nor do I have anything to read any codes it may be showing.
View 14 Replies
I am new to the v10 I only ever owned 7.3 this is my father truck it's a 99 with 200k on it. The problem is it will idle fine when cold but when it is warned up very ruff idle no codes and when I go back at the end of this week I will check the O2 sensor with AE but I really don't know much about it.
View 2 Replies
So I have a 2003 6.0L Powerstroke 1 ton. I just replaced the starter thinking the solenoid was the problem. But my luck it wasn't. I turn the key and the ding stops and it's quiet. Dash lights go off. I have the engine light and water in fuel light on. ABS is on I think aswell. I've run out of options.
View 1 Replies
We have a 2008 f250 super duty with the 5.4 triton well ever since I replaced the power steering pump its been running raggedly, it idles rough and when i get up to 50, 55, 60 the check engine light comes on i put a diagnostic reader on it and said something along the lines of ECU bank 1 an Bank 2. What that is and I've been a mechanic for almost 3 years.
View 2 Replies
2006 F53 (motorhome) with 6.8L V10. Rcently noticed rough idle and midrange (under load) mis fire. Had codes on 2 coils. Replaced coils and put new spark plugs in. Did not improve and now detecting mild back fire.
Just completed compression test. 1=207psi, 2=200, 3=210, 4=190, 5=197, 6=200, 7=200, 8=170, 9=202, 10=208.
put some oil in #8 and retested at 225!
Other observations on #8. Engine has ticking noise chased with stethoscope to #8. THE new plug with 200miles, insulator going to electrode tip and everything inside combustion chamber is black. All 9 other plugs still look new out of box.
With the ticking noise I was suspecting valve but the compression test with oil jumped way up.
View 14 Replies
2001 f250 v10 6.8l runs a little rough at idle, low rpm is ok between 1700 and 3000 rpm but around 3 it starts to shudder while driving let off gas get back on its fine, new plugs 1,000 miles ago has throttle body spacer and cold air intake, stock everything else..
View 8 Replies
I have a 99 f250 5.4l 2v with 165000. just two weeks ago i went to start up the truck on a job site to take lunch and it was running really rough. I talked with a mechanic at my shop and he said that it sounded like the aic or that i needed plugs. I went and bought aic and plugs and installed them all in one day. I unhooked the battery before i did any work and have changed the coil packs about 3-4 months ago when it was jerking at highway speeds. I am at a loss.
Read so much on the site about could be this or that and cant afford to through money at it like the govt does. I replaced the ait(air intake temp sensor) and the ect(engine coolant sensor) after i got a code from oreillys that said p0113 which is high input on it. I have read it can be so many things and it seems to be running rich because i am getting about half of mileage i was getting before problem started. i need a fix soon as i must drive the truck to work everyday which is a 52 mile trip total.
View 14 Replies
I have a 2002 F350 with a V10, this just started happening where at times the truck will turn over but won't run... after a few times of trying to start it I pull the key out let it sit for 5 seconds then put the key back in and runs perfect..... now at the gas station the other day it started but ran like it was on 4 cylinders... I turned it off and restarted it and runs perfect. Heading to Kansas next week to pick up my boat and don't need problems....
View 4 Replies
2005 250 5-speed total oil pressure loss ... At 110k mechanic diagnosed failing phasers from noise, rough idle, loss of power under 1k rpm. (Crew cab long box xl bought new for $25k)(first 100k were from carpenters (hard miles) so this truck is barebones and usefulness is much higher than cash value). Truck has 146k
All symptoms typically disappear over 1k rpm so I have limited idle time and manipulated engine speed to try and maintain 1000-1200 and all has been well for past 36k miles. Today noise (valve clatter?) persisted at all rpm and during a scramble to get off the highway all oil pressure was lost (I'm aware that pressure gauge on dash is not 100% reliable). After total pressure loss I cut engine and called tow truck. Out of curiosity, I actuated ignition and motor cranked maybe two rotations, and then appeared seized. After about 45 min waiting for tow I went back to disengage 4wd and take my rifles and skis out of truck. At this time I actuated ignition again and engine fired and ran as it had for past 36k miles. I drove about one mile constantly watching oil pressure gauge, then noise returned followed by instant drop from normal to 0 pressure (dash gauge) I immediately shut of engine.
I am a mechanical engineer, but not a mechanic. I am familiar with the cam phaser system and I understand that their operation is directly related to oil pressure. Today's temp was under 0'F. I have a very skilled mechanic who works for around 30-40% of cost of licensed shop and I know his skills to be on par.
View 4 Replies
