Ford Super Duty (1999-2016) :: 2003 - Replaced Steering Wheel And Box - Lock Out - Pulled Itself Across The Center Line?
Sep 12, 2014
I have an 03 F-250 4 wheel drive with the 6.0. For the last 3 months or so I have been having some issues with the steering system and I am not quite sure what it could be or what too look for. I have already replaced the power steering pump due to the shaft seal leak on my old one. After that I noticed that the truck would never really center the steering up on its own like it used to and that it pulled in either direction depending on which way you steered it. I then decided that I would replace the steering box on the truck. I replaced it with a Napa one. Right after that I had it on the alignment rack and the guy said it was not even out of alignment. As I continued to drive the truck it continued to pull in either direction whenever you took a hard turn in either direction. Then one night coming home from work, I was pushing it a little hard, the truck pulled itself across the center line. The steering wheel and all turned to the left. It did this 5 or so times in a row. I am also noticing some issues with my lock outs but don't know if it is tied to the same issue with the steering.
View 3 Replies
Advertisement
06 F250 6.0 CCSB 4x4 163K Truck was in a pass side wreck about three weeks ago. Aside from bumper, head light, etc I had to replace the track bar and then I had the alignment done. Mech said the steering was loose and was either the steering box or column.
PROBLEM: Truck drove and parked fine last night, I went to leave the driveway this morning and I had to turn the wheel full right while backing up. The wheel locked up and wouldn't turn back to the left to straighten out. Hood wouldn't pop either to check anything
I crawled under the truck, the belt was in place and I didn't see any power steering fluid leaking. Thinking it was a PS problem and the hood not opening, I basically floored it and yanked on the wheel and it broke loose. Also, for what ever reason the hood opened after that
Now the steering is heavy and the wheel doesn't center on it's own. It will stay turned when I let go of the wheel. Scared that it would happen I didn't try turning it full lock on the way to work. but it happened again exiting the parking lot, again full right lock and the wheel stuck.
I managed to yank the wheel to the left again and I heard a distinct pop from what I'm sure was the pass side wheel area.
The PS fluid is dark and I'll figure out how to change it. I've read issues from the U-joints, ball joints, Steering box, steering stabilizer, and failing PS pump could all lead to this. Being the truck had a pass side fender bender, and I'm pretty sure the pop sound came from the pass side how do I check all of these items.
View 13 Replies
Today I put a new shifter tube in a 02 f450. Everything works well, but the key won't come out and the steering wheel won't lock. Was told there is a button to push by the turn signal side but don't see any. Looked around top and bottom of column and didn't see anything out of place. Also found a black wire with a pink strip not connected to anything. Touched the wire to the column and key dinger sounded. Where should this wire be connected?
View 14 Replies
2001 F250, 5.4, Replaced the clockspring and now my steering wheel feels very tight. After cornering, it doesn't come back on it's own, like something is rubbing. The face of the clockspring is slightly different than what was there.
View 1 Replies
On my '97 F250 the rear brake line going to the rear right wheel has a rusted hole. It measures 50" total. Instead of bending a new metal line. I see they have a "poly armor" line that can be bent by hand( no tools needed). I see Autozone has them.
View 14 Replies
I'm wanting to get a single in-line steering stabilizer for my '05 F250 4x4, but I can't seem to find any that include brackets.
I don't need a dual setup because I'm not running a big lift or big tires, but I want an inline stabilizer so that I can just leave the stock one in place.
What is the part number for one that comes with the mounting brackets?
View 7 Replies
I blew a power steering cooler line yesterday and lost a bit of fluid. Removed and replaced the line, consequently losing most of the fluid in the system (during line replacement). Re-filled the system and now i have great power steering when driving but none at idle. If I bring my RPMs up about 150-200. I get it back in full force. Could my PS pump be on the way out or might this just be air in the system?
View 3 Replies
I got a 2011 250 SD 6.2, I have what feels like a catch in the steering, on center, when you turn the wheel feels like it just gives and stay's there, either way you turn, Checked front end, ball joints tie rods etc., the hubs are unlocked, feels like when the u-joint on the steering shaft goes bad and you get that bind. But this truck doesn't have them anymore, just a rag joint at the box. It only binds at center, and wont return, took steering stabilizer off and road tested same thing, air in tires good all the way around, has about 58,000 miles on it.
View 6 Replies
Just bought this '08 F250 CCSB 4X4 5.4 Problem is the steering seems heavy, it tends to wander at higher speeds and won't return to center after a turn. I've searched on here and found a few possibilities (axle u joints, ball joints, steering gear, etc). I have an appointment with the dealer on Friday to fix it under warranty but he is convinced it's the u joints in the steering shaft seizing. When my F150 steering shaft began to seize, it would be hard to turn then break free then be hard then break free and this is not what is happening on the SD. I haven't had a chance to check the front end myself but not sure how you would check the axle u joints if there was no play in them. How would you check to see if they were seizing up.
View 3 Replies
I replaced the power steering pump on my 2000 f250 Power stroke. I bled the lines, and when the wheels are on the ground, I have no steering. When I raise the wheels off the ground, I have no problems turning stop to stop.
View 9 Replies
Have a 2007 V10 and I want to put in a Magnafine tranny filter. Instructions say to plumb it in to the return line. Which one is this, top or bottom?
View 11 Replies
I have a 2001 SD 7.3 Manual, in which either the rod or the actuator has broken. I can tell yet which it is. I can mover the lower actuator back and for but that doesn't tell me which part is broken. I have the parts on order to replace. I have been searching without success to find detailed instructions to make the replacement.
I run a small shop away from my day job but have never dug into one of these. Being the various small parts and sequence of disassembly/Assembly I want to do it correctly the first time. It's very strange how you can go to YouTube and search for everything under the sun with great results, except for this.
View 2 Replies
Had the rear passeneger side brake line burst today in rush hour traffic ..wasn't much fun. Is it a easy to do it yourself deal ...it is a 2003 f250 v10 triton .
View 1 Replies
Steering problem... 2005 F250; Four Wheel Drive; Automatic; 93,000 miles; gas engine. The basic description that I have been giving people is that the steering will "stick" or "lock up" to the point that I have to use some force to get the steering wheel past the stuck point, when it releases, it's a " jerk, " THEN it sticks the other direction and I have to force the steering wheel back the other way again. So, in other words, when the truck decides to do this, in order to drive a straight line I am literally turning the wheel back and forth, probably only an eighth of a turn each way, but back and forth. If it's bad enough, I have to pull the truck over.
If I pull over, sit and turn the wheel back and forth a few times, loosening it up (when I'm stopped, I can't say that I really feel it stick at all), I can pull back on the road and be fine. A lot of the time, it happens right after I've turned a wide corner (not specifically right or left. It does it both ways), say taking a corner at an intersection as a yield or turning through a wide intersection onto say, an entrance ramp to the highway. I would say in a lot of cases, even when the truck doesn't have "an episode," I can still feel a stiff spot when I'm driving down the road/highway. This is not a vibration-type problem.
View 4 Replies
I noticed yesterday that my tire on the driver's side has rubbed a flat spot on the rubber brake hose. I bent the metal tubing so that it doesn't rub any more, but should this be of great concern? Obviously I'd hate for it to rupture, but it looks as though it's not too bad.
View 1 Replies
the mechanism that locks the steering wheel is stuck. not the ignition key cylinder (already removed that). how do I release that mechanism to free the steering wheel.
View 3 Replies
I made a bone head mistake and crunched the steel brake line between the rear axle and the passenger side sway bar mount. Truck is a 2003 F-250 with a 7.3. I would like to go to the auto parts store, get bulk steel brake line and bend it myself. But, I don't know what size the line is or what size the fittings are. Whatare the sizes???
View 3 Replies
I just replaced my fuel pump to avoid another tow truck ride and now my fuel gauge is off. I filled up the truck today and the fuel gauge is only showing half a tank. I turned the truck on and off several times to try to reset it, but that didn't work.
Truck is a 2003 with the 5.4.
View 1 Replies
Seems that after a sharp right turn, for instance turning right at a stop sign I'll get a loud pop that I can feel in the floor pan under my feet.
After the pop the steering wheel and whole front of the truck will shift left and right like someone is grabbing the wheel, sometimes violently. If I drive slowly it will cure itself and sometimes not do it again for several days. I've check ball joints and hubs and they are in great shape. I pulled the hubs and greased the needle bearings about 6 months ago. I checked all steering components and the linkage that attached to the steering arm had some play so I replaced it. Then I found that some idiot took the steel sleeve out of the bushing in one end of the steering stabilizer. I bought a new stabilizer and cured a pop I'd had since I got the truck, but the other issues were not solved.
Alignment has been checked too.
View 14 Replies
My truck has developed a wobble in the steering wheel. I don't mean when you are driving down the road, but the steering wheel wobbles around. It wobbles in any position that the Till shaft is set to. How to repair.
View 10 Replies
just bought this f250 seems to walk on the road alot, had it looked at has new balljoints, he says everything seems tight except there is lots of play at the gearbox, is it recommended to have it rebuilt or buy a reman, was told that even the reman seems to be the same way
View 14 Replies
