Ford Super Duty (1999-2016) :: 2003 F550 Truck Died While Running / Temp Gauge On Dash Dropped To Cold
Aug 21, 2015
The truck I'm working on is a 2003 f550 with a 6.0, and 382000 kilometers. My service truck died on me couple days ago, while running. As I rolled to a stop, I noticed that my temp gauge on the dash dropped to cold. (Truck was hot). Tried starting, and I have a crank, no start situation.
After towing it to my shop at work, I hooked it up to my scanner, and found that the pcm will not communicate with the scanner (otc genisis). I have no injector buzz with key on, wait to start light comes on for an abnormally long time. I have 48.3 volts on the ficm,(4 screw), and haven't been able to find any chafed wires as of yet.
View 1 Replies
Advertisement
2002 7.3 powerstroke, no info about service or work done, looks to have a new hpop, know for sure that there was a new lpop installed, claims no gouging in front cover, died going down road oil pressure gauge on dash dropped and was taken to a shop and did not get complete diagnosis, where should i start? Shop drained oil to take sample and no metal shavings or flakes were present according to them...
View 3 Replies
I have had this issue with the truck 2008 F-250 6.4L since I bought it a year ago. At first it seemed as if the truck wouldn't start whenever the water temp gauge was working while she was hot. When the gauge wasn't working she would start right up like a champ. Well a year later ( have only been driving it for 6 months) a full engine rebuild, new high pressure fuel pump ( injector pump on top the engine below the turbos) she still won't start when she is hot. What the issues are.
Right after the engine rebuild I was getting the p088 code which is for the hpfp but since I cleared the codes right after the engine was rebuilt I haven't gotten the code again. I replaced the high pressure fuel pump this last weekend hoping that it would solve all of my issues and she would be like brand new again, but it didn't do anything. When I ran codes right after I installed the high pressure fuel pump I got a few codes p0684 which is the glow plug control module p0284 ( google said) gear lever y position correct but I'm unsure if that's right.
P0528 which is the fan speed sensor circuit ( that was unplugged during the removal of the hpfp and power steering pump or the radiator) p0480 cooking fan circuit ( also unplugged ) p174e out put shaft wheel speed correlation ( not concerned about that one) p008c fuel pump control circuit p008d fuel cooler system ( taken out and unplugged using installation of new hpfp) p115a ( low fuel level forced limit power) that is from trying to start while she had a little bit of air in the system after replacement) p2291 injector control pressure to low- excessive cranking ( probably from the air in the fuel system again). I cleared all those codes once I got her up and running again. Checked for codes yesterday and the only one that came up again was the p0684. Where to check next for this hot start issues,and don't know what to do at this point.
View 4 Replies
I have been having a problem with my 2002 F250 Super Duty 4x4. It started about 2 months ago. I was in traffic (truck hadn't even been on for 15 minutes). The temp gauge spiked, so I pulled over and turned the truck off. I turned the ignition on and the gauge was normal so I started it and all was fine.
Fast forward a little and every so often about every 3 weeks it would overflow (coolant) but not get to the point that it would overheat. I changed the thermostat and all seemed good to go. Fast forward to yesterday morning. Got in the truck and left to go hunting, and I didn't even make it 10 minutes down the road when I turned the heat on and it blew cold.
I started to see the gauge creep up so I pulled over and shut it down. Upper hose was cold, lower is cold and both heater hoses are cold. After some time of waiting, I started it but the gauge kept creeping up and no heat, so I kept shutting it down. After about 5x of this, the heat worked and the upper hose got hot and all was right with the world. SO I drove it home. Coolant is new, flushed about a month ago and was running great since then. Thermostat is new. Do I have a blockage somewhere? Water pump bad?
View 4 Replies
My F250 with V10 has developed an overheating problem. While driving, the temp gauge suddenly shoots to max, and the truck goes into limp mode. Turning off the truck and ignition, waiting a few minutes, and all seems to be well again - sometimes for only a minute, sometimes for several days. No steam leaking, the water in the reservoir seems to be normal temperature, the radiator is not overly hot, and the AC keeps on blowing ice cold. Me thinks it is not really overheating, it just thinks it is. So where to start? Change the temp sensor first, or the thermostat? It seems the hoses are fairly firm, I don't believe they are collapsing from suction.
View 14 Replies
I have an 03 with a 6.0 diesel, going down the road and started losing power and then died. Won't start, and I don't have a scan gauge. Several sources said ipr valve, and from videos on youtube I thought may be a good place to start. I bought a socket and pulled the valve, to check the screen. There is no screen whatsoever on the ipr. The oils clean, as I had changed it about 200 miles ago, and I ran a magnet in the hole looking for a screen, couldn't find anything so I used my fluid pump in the hole. No trash, screen or anything. Do some ipr valves not have screens? What would be my next step??
View 2 Replies
Recently purchased 2006 F-550. Noticed the brakes seemed a bit squishy and weren't stopping the truck as well as I thought they might. Looked under the car and saw this at the right rear tire. Give it to me straight, doc.
View 14 Replies
I am trouble shooting my temp gauge. I have a 1997 f350. I brought the truck a year ago and i have still not fix this problem. I install a new temp gauge and nothing changed. When ever the truck is running it reads cold and doesn't budge. Ive read that the gauge can be broken its self but during a few hot times over the summer. The gauge began to rise slower, never reaching normal temperature. A few times i messed with the heat and the gauge would shoot over the normal temp. The truck seems to run at a good temp sometimes hot though. The tube on top of the radiator is hotter than the bottom also.
View 3 Replies
I have a 01 F550 Super Duty with a dynamic wheel lift system. One of my drivers was driving the truck when it just stopped running. I can't figure out what's happened. I think I have checked everything and yet it just turns over but won't start...
View 1 Replies
My 2003 6.0 truck lost most of its power. It has the SCT programmer. It used to run great it would roll coal really well then it slowly started to run worse. Now it runs really sluggish especially when its cold. IT takes forever to warm up. On the freeway when ur going a constant speed it bucks and jerks a lot. It won't roll coal anymore and just runs like crap. A mechanic said I had 3 bad injectors. But I don't believe it.
View 2 Replies
I bought a 2006 F250 6.0L a couple of months ago, from a dealership. It's been bulletproofed already, has an intake, coolant filter kit. Has 95k (mileage). Today, my fuel gauge dropped to empty from 3/4 of a tank for a couple of miles and set off the CE light. I hooked my scan tool to it, to clear the code (P0460).
After just checking other things out with the scan tool. I cleared it and went on... I had to run to the store, later on... I was pulling out of the neighborhood and the gas pedal was a lot more "touchy" and the truck, responded to it and it launched pretty good and blew a good amount of black smoke.
Do any of you think this has/or had a tuner on it and I may have activated it with my scanner?
View 6 Replies
Just got done with a ball joint replacement on my 2003 F550, everything went together great, just as it should. Until I got to the drivers side hub lock.
I have Mile Marker 449s/s manual hubs. Turn from free to lock and theres this loud clicking sound about halfway to LOCK (passenger side doesn't do this). Hub will stay locked for about 2 rotations, then it unlocks and makes a clicking sound. You cannot turn the hub back to FREE, it gets halfway and stops. I tried forcing it and broke the spring fingers inside. Have a new set on order.
Is this a locking hub issue or an assembly error? I was going to take these steps.
- Take passenger side hub lock off and see if it operates normally or same on drivers side.
- If same, remove axle and re-seat/re-assemble everything again
Anything to specifically check? All the parts went back in, washers were in correct order, outer snap ring is in groove.
View 11 Replies
I have an 03 f250 6.0 150k milage and lately my A/C has not been working at its best. Its intermittent, and for some reason it will work fine until i get on the highway and it just blows hot air. Would this be a leak or clutch issue? One thing I have noticed if my oil/coolant is above 200 the A/C will blow hot air but not return to cold when the temperatures return to normal. I haven't done any trouble shooting so my first thing ill check are the fuses. As far as the compressor goes its an alien object to me I have never had A/C issues with any vehicle i have owned.
View 6 Replies
I have an 02 F250 V10. Ive always wondered about the transmission gauge. It seems to always point to the middle of the gauge range. This weekend I was pulling my car hauler up and over the Ozark mountains, and when I stopped for fuel I noticed the transmission was vomiting fluid underneath the truck (and on my exhaust creating a nice smoke bomb for everyone around me). The gauge indicated normal temps. It kind of gave me a sick feeling. I have ordered the 6.0 Trans cooler from Rock Auto and a new temperature sending unit. Do the trans temp gauge is supposed to move or is it pretty much useless?
View 14 Replies
I had a mechanic replace the temp sensor on the top of the intake in my 2001 f350 v10 and since then my temp gauge doesn't work. He replaced the sensor again and still nothing. Is there a different sensor/sender that controls the temp gauge???
View 4 Replies
Driving down the highway, battery gauge read fine power, but battery light came on. In a remote Alaska situation so I couldn't diagnose, plus truck is new to me. Kept driving towards civilization. All gauge dropped. Then lights dimmed, then truck died. This was over about 15 miles. At night with lights on. Truck has a plow with plow lights, aftermarket cranking stereo which I was using, heater on (Alaska). It sits 70 miles up the highway from where I'm at getting ready to go back and work on it. So...
Of course first thought it is the alternator, not providing enough power for all this. Looked inside, it is a newer looking reman. Belt is fine. My question is, if not this, what else could it be? I'm hoping to haul the alternator and whatever else out there and get it going without having to drive back and forth for more stuff I need. I can always return stuff I don't use. Probably I'll throw a new battery in it as well. But after that, anything else I should be thinking/ready for?
View 4 Replies
I have a 2003 F550 6L diesel flatbed truck. Last week, the overdrive button would activate by itself. I'm assuming there was a loose wire so I taped the button to keep the overdrive off. Two days later, the overdrive came on while the button was pressed in and then smoke came out of the steering column/lever area. I pulled over and turned off the truck. The smoke stopped after 10 seconds and I restarted the truck. The overdrive light/functionality no longer worked and the instrument cluster also wasn't working.
The next day I was driving, and the truck died at a stoplight. I got it towed home, and opened the steering column and noticed that the overdrive button wire had burned. I removed the harness clip and charged the batteries. It started but the instrument cluster still didn't work. 2 minutes later the truck died. I replaced the alternator but still it won't charge the batteries. The truck dies 2 minutes after getting a battery boost to start the truck. The instrument cluster also doesn't work. What could be causing this issue?
View 1 Replies
My truck threw a code p1299 last night on my way home from the lake. I was towing on a huge grade and all the sudden my engine temp gauge pegged out on me and check engine light came on. I pulled over and noticed a bunch of coolant had overflown the cap but the engine didn't seem to have over heated. When I restarted the truck the engine temp was immediately normal range. I drove for another 30 min or so and the engine temp started to climb and then come back to normal then climb and stay pegged. I pulled over again and noticed the coolant level was low and coolant had overflown the reservoir. I restarted the truck and once again it was normal. I just drove surface streets the rest of the way with no issue. I suspect blown head gasket. This is a 2003 F-250 6.8L with 100000 miles.
View 8 Replies
I got in my 06 f250 tonight and my digital read out on my temp control not working. My heater and A/C works but when I turn it off my outside temp is not on. Whats going on?
View 3 Replies
My truck ran and drove then I changed my Steering Gearbox. After all that, I went to go start it, the trucked cranked and the batteries died. Hooked up the charger then and nothing, No start no crank. F250 2006 diesel 6.0 ...
View 14 Replies
Ok so my fire station has a 2003 f550 rescue truck with a rescue body with the round tail lights, we recently upgraded them to the LED ones that are much brighter but of course it flashes at the speed of sound. The question I have is:
1. the relay {flasher} is located on the driver side inner fender? I think....
2. does the same EP-27 relay/flasher fix the problem?
View 1 Replies
