I have an 03 F350 4x4 dually. Was pulling hard left at low speed when braking (front). Replaced pads, calipers, rotors, hoses and tires. Still the same problem. You can feel the abs activate right before it almost locks up the left front brake (basically will pull the steering wheel out of my hand). BTW the abs light does not come on.
View 2 Replies'08 F350 6.4l 4wd, I had the truck come in with a exploded transfer case. (See pics). Ive read all about this happening to many others. The truck still drove, hubs not locked, plenty of fluid in the TC, pretty sure it was the double Cardan that did it. Anyways I replaced thwith TC, replaced the front driveshaft, filled the TC with recommended fluid. Test drove and drives great, shifts fine. Only until I turned left.
At slow speeds turning hard or 15-20 taking a turn, it sounds like a ratchet clicking from somewhere on the left side, right around the drivers door, from what I can hear from the cab. Does it in 2wd, 4wd hi/low, hubs locked or not. I changed the vacuum pump, no leaks, changed the IWE solenoid, pulled out both locking mechanisms, tightened crossmember, checked everything from the hours of research I did on the internet. I cannot find the problem. I don't know what else to check. Front axles free spin and lock when they are supposed to. I'm at the end...
My Superduty has been pulling to the left when I hit the brakes for a few months now. In the past it's done it, like within a year or two after buying it brand-new off the lot, but that was because one brake pad had rusted itself to the bracket and was not doing a darn thing. Once or twice more, it was a stuck caliper pin, which was quite obvious when working on it.
Last year, around August, I replaced the rotors and pads with Advanced Auto parts stuff. Rotors are still great, pads look brand-new, and it wasn't pulling up until the past month or two.
But this most recent pulling has been a problem that I can't find. It's not the pins, it's not the pads, and now I find out, it wasn't the calipers
This past weekend I went so far as to replace the calipers with Napa rebuilt "semi-loaded" calipers (all hardware and pins and bracket, except for the pads) and pressure-bleed the entire system. The old fluid was green, not black, but now that it's been bled, the pedal is a bit firmer than it was.
I wasn't going to replace the calipers without checking them first, but I broke both bleed nipples off and I wasn't about to wrestle with an easy-out and try to get the darn things out. Per side, rebuilt caliper with hardware and bracket, can't go wrong. (Checking the calipers would have involved using a C-clamp to compress the caliper slightly, then backing off the C-clamp - if the pistons come back out a slight degree, they are free and the seals are still "grabby" and resilient).
While bleeding it, I saw a piece of black crud (rubber?) about 2-3mm in size come out of the left side. Didn't think much of it, figured it was just built up crud from somewhere.
Today, the first commute after doing the calipers and bleeding, it's still pulling just like it was before the calipers. However, I did notice at one point when I hit them, they pulled like they normally do, but seemed to go straight a few seconds into it. It does seem that if I keep my foot on the brake, the pulling is much less after the initial second or two, but if I stab them again, it pulls like crazy.
And by "pull" I mean the steering wheel actually moves in my hand. So with that in mind, it's actually a front-brake problem. If it was the rears, the wheel wouldn't pull like it does, and if it was something loose in the suspension, I would have found it already after checking everything, and it again, wouldn't pull the steering wheel like that.
Now, given that black piece of whatever that came out of the left side, I'm beginning to wonder... if it was rubber from the inside of the hose.
Is the right brake hose causing the pulling because it's coming apart just like the left one might be?
I've gone over and over this in my head this morning, and thought about the ABS unit possibly dumping pressure from the right because of a leaky valve (see side note below), but I would think that once the pedal stab was over, it would even out and not pull at all.
However, this thing pulls left quite a bit, even after the pedal has been held down for quite some time. Usually. Sometimes, it subsides and doesn't pull. But mostly it does no matter what I do, keep pressure on the pedal, let up and reapply, whatever.
Does this really sound like a bad hose? It's intermittent, but usually pulls like 90% of the time.
Side note: The ABS unit in my truck, and most Fords of the time (not sure about later than 2004 or so) is a Kelsey-Hayes three-channel unit like this:
Kelsey-Hayes RWAL Antilock Brakes
It's the same system found in Chevy Suburbans and light-trucks, which I have worked on before and know a bit about.
In my case, it can't be a dump valve leaking, because it would effect pedal-height and not PULL to one side like it does. The only way that could happen is if the isolation valve was closed, AND the dump valve were leaking at the same time.
I haven't, however, gotten the ABS to activate just to see if it changes anything. On my way home tonight I will see if I can find some dirt or sand and get it going
I have a 2003 F350 6.0 King Ranch. My first diesel truck. Bought it in March 2016. One owner with 102000 miles on it. Has a Bullet Proof oil cooler and 4 inch exhaust. Truck ran great until a week ago. Now, under any hard acceleration it blows out blue/gray smoke and does not seem to have as much power. Coolant level is constant and I cannot find any traces of water and oil mixing.
View 2 RepliesWhat this clunk could be?? in my truck in signature, 2003 F350 CCLB 4x4, 4" lift. its only low speed, on very light bumps. really does it when the truck flexes, like turning into an elevated driveway or something. driving me absolutely insane the last few months. it sounds like its coming from right under my feet
-removed front shocks and drove
-removed front sway bar and drove
-front wheel bearings are new and tight
-front leaf spring, rear upper shackle bushings are new (thought that was problem..no)
-front leaf springs and bushings are new, although i suppose its possible to have a bad bushing already
-removed traction bars and drove
-removed front track bar and drove, but going to try this again.
-all cab mounts look ok
-took out cab mount under drivers foot, and cut down the metal piece a little...read about it on another thread on here. no change
-made sure my gooseneck ball couldn't rattle
-steering box is new...thought that was it
-steering shaft is solid
-transmission mount bushing and crossmember feel tight
-lubed front driveshaft slip joint and it doesn't have any u joint play
-rear shocks seem ok but haven't removed them yet
-fuel tank is solid
-rear driveshaft has new carrier bearing and u joints, all is tight
-exhaust is not hitting anything
-u bolts all tight, spring bolts are tight
As you can see, I've been through damn near everything. my only thoughts right now is a possible bad cab bushing, or bad leaf spring bushing...as it sounds like its right under my feet. and when you flex the truck, it makes all sort of popping and clunking noises. i had the truck on my buddies lift and we went under it for an hour yesterday looking around with no luck. only thing i found was a bad traction bar bushing but we removed them and it still does it..
Most noticeable at the end of the video...it sounds exactly like a bad sway bar bushing but that's not it...
Front end clunk - YouTube ....
I'm looking at purchasing a 2003 F-350 from a Ford Dealer, Drove the Vehicle last night and the Gear shiftier was very tight and hard to pull down. Is this a real concern? The Sales guys said its better to be stiff rather than sloppy. But they will say anything, right. The vehicle is a deal and so I'm looking to find out why.
View 1 RepliesDriving on a paved road(some potholes but nothing bad) came to stop sign. After waiting for trafffic to clear, made right turn onto state highway truck began to pull to left, at first I thought i had a flat tire but every thing looked okay. Drove two miles to home, if let the steering wheel go, the truck would change lanes in about 25 feet...
2002 ford crew cab 4x4 7.3 power stroke 20k on Michelin.
My 2003 F250 6.0 pulls to the right when driving at any speed. In order to keep it going straight the steering wheel must be slightly tilted to the left, not much but a little. When the brakes are applied hard it will go to the left slightly if you are not holding the wheel good. Neither of these are terrible, just a nuisance. I'm worried about uneven tire wear too. One front wheel bearing was replaced a few weeks ago. It had this problem before that and still does after. Does this sound like an alignment or maybe something more?
View 13 RepliesI need fixing my 2003 f350 6.0 diesel, I have been working on this truck for a while and still am having problems, here was the original symptoms:
-Hard start or no start on a sunny day
-Rough idle for 10-15 minutes
-Rough shaking in the low RPMs (35 mph)[/COLOR]
-Slow response from the gas pedal
-boost would only get to 14
My dad and I then did many things to the truck in the shop, those things are:
-Air test and replacement of coupling going into oil branches (next to HPOP)
-Replaced EGR valve (no good)
-Replaced ICP sensor (leaking oil)
-Replaced ICP sensor and IPR valve piggtails (due to frayed wires)
-Cleaned Turbo
-Cut MAP sensor hose and reattached it (spliced on the end)
-New battery
-Performed a bubble test and found two bad injectors on passenger side (injectors #5 and #7)
-Cleaned and lubed tops of injectors
-Replaced O rings and copper crush washers on all injectors
-Replaced nipple cup O rings (tight)
-Blew out injector cups
-Bubble tested after injectors put back in (no more bubbles)
-New FICM, EGR cooler and oil cooler were already installed
-Ohm'd main engine wiring harness (good to go)
-Taped up frayed wires on fan clutch connection
-Increased wire gauge on the positive jumper between both batteries
-Sanded each ground on the batteries and engine, cleaned battery clamps, lithium greased connection points.
-Checked fuel for air (no air)
-Checked fuel psi (85 psi, plenty)
-Oil changed
After doing all of this (diagnosing as we fixed each thing) we now fixed many things including the hard/no start problem. Now, for the first three to five minutes:
-It starts right up
-Runs perfectly, no shake and instant response from the gas pedal and turbo
-Boost goes to 28
-ICP is 800-950 on idle
-IPR is 25-26.9% closed
After five minutes however:
-Starts to shake
-IPR % starts to raise
-Received no response from gas pedal (absolutely no power)
This truck has been torn apart like 8 times and I have to do it on my spare time.
Best truck I ever had but around 200k would occasionally blow a bunch of smoke when pulling a heavy load.
My 2000 f 350 xlt triton v8 has done the same thing a couple times (about 200k miles).
The (cough) "truck expert" at my local dealer has never seen that before but its happened in 2 different trucks for me. It never caused a problem other than scaring me.
I sold the 02 last year when i got a 2011 f 250--it was 12 years and 300k miles old and never was hospitalized except for a fuel pump due to my negligence of filter.
I've noticed that my 06 f350 will pump the ABS when pulling in muddy spots, mostly in 4x4? It will even start to cook the pads after a bit of spinning. I'm not doing any serious off-road stuff, just trying to pull random farm equipment/trailers. Do these trucks have some sort of traction control that I don't know about or dose my ABS think I have my foot on the brake all the time?
View 9 Replies.I just changed out all the steering linkages due to a lot of slop and worn out tie rod ends. This problem existed before I changed them but I thought for sure changing the linkages would fix it. When I brake hard my front tires wobble very bad. I haven't ever experienced the death wobble that is common in these trucks, but the symptoms seem the same, its just only when I brake hard. I can look at my front left tire while braking hard and see it wobbling. The wheel bearings and ball joints only have about 15k miles on them. I can't tell if the front wheels are moving independent of each other back and forth, or if they are both shaking back and forth together. What might cause this? it's a super uneasy feeling when it happens, especially because whenever you are braking hard there is usually a reason.
View 14 RepliesI'm having trouble finding the source of a vibration in the front end if my 1999 f350 super duty 4x4. The vibration is felt all the time but worse when under 40mph, while braking, and especially when turning.
I have replaced the rotors and brakes, tie rods and Drag links since the issue started but no change. In the vibration. What should I check next?
When braking the truck shakes terribly, enough to toss a drink out of the cup holder almost. Sometimes there is a slight feeling in the peddle but not always. The shudder feels like it is timed with each revolution of the wheels.
It developed from a perfectly stopping truck over the course of maybe a month. I don't drive the truck that much either.
Things I have checked:
1, all u-joints, they all look and feel good, no play or slop in them
2, air pressure in all tires, even rotated them, no effect
3, brakes-front and back all looked good but I went ahead and replaced front pads and rotors, cleaned caliper pins, zero effect.
4, shudder exists whether in gear and slowing or in neutral, 2wd and 4wd
What the heck else is there to check? My first thought was, front brakes/warped rotors, but after pulling them apart there was so much life left on the rotors and pads and replacing all that with new did nothing! Could bad back brakes cause this much of a shudder? They look fine as well.
I tow 10-15K; 6-10x per month with this truck. I can feel the braking ability starting to drop off so I want to get them done pretty quick. I am more or less happy with OEM performance but if there is a better value, and with my SO starting to haul the horse trailer around.. I wouldn't mind upgrading.
What is worth the money? I'm fresh out of school trying to figure out what the best value is.
Calipers?
Rotors?
Pads?
Brake Lines?
What would provide me with a noticeable improvement without breaking the bank?
Last question, could worn rotors cause vibration/shaking in the steering (primarily when turning ramps) at 50-60mph? Tires are brand new, problem showed up before they were replaced.
First off I want to say I love my 11 f350 6.3 srw she's a awesome truck. I pull a small 7x14 trailer for my biz..
(3600-400) is the usually weight, I always use my tow feature. One day last week I start out hit my button in go, but I notice the engine braking/down shifting wasn't working. The trans still shifts smooth n normal the light is on the dash but no tow engage.
I check the transmission wire plug to make sure it'd getting a good connection, it does. I take the rubber boot off next to the shifter look at those wires they look ok not pinch or nothing, so I'm stumped.
I have a 1999 f250 sd with the 7.3. I'm not sure what is going on with my pickup. When I turn to the right i can turn with one finger, but when I turn left i have to put some muscle into it. Power steering fluid is full. I raised the front end and it turns both ways easy. My ball joints feel fine, there is no tire shake when i have it off the ground. My tie rods feel fine also, nice and tight. I was thinking about replacing the steering sector to see if thats the issue but wanted to get a second opinion first.
View 2 Replies2014 F450. Front end and steering wheel shake violently when braking while towing a 20,000 pound trailer down a long and steep highway grade. It does not happen when towing my 12,000 pound trailer down the same highway. Could I be setting off the ABS braking system?
View 14 RepliesI replaced both front bearings, calipers, brake pads, now I have a grinding noise on the left side front stops sometimes when you step on the brakes? 1999 F350 ...
View 6 Repliesi have a f350 superduty with a 7.3 turbo diesel and I pretty much hafta keep it plugged in to get it to start, i have installed all new glow plugs and both relays have been changed and the problem is still there, only other option i have not tried yet was changing the pcm controller but unsure if that is the problem ..
View 14 RepliesI have a 2011 F-350 6.2L that has extremely hard shifts from 3 to 4 going up and 2 to 1 going down. Sometimes on downshifts it feels like something has ran into the back of the truck. I had the computer updated when the truck had approximately 40,000 miles on it and he assisted a little bit. The truck now has 140,000 miles and it is back to shifting horribly. I put it in the shop at the dealer on 30 December 2013. The dealer says that the problem is that the shift solenoids need to be replaced but that they are not available. The truck is still sitting at the dealer and I am being told that the parts should be available mid February.
View 10 Replies