Wipers/washers didn't work on 2003 f250. No blown fuses in system, supply fuses are 106 and 33, removed wipers and found no voltage on dk/grn wire of connector (fuse106). Turns out that the wire bundle had chafed a wire near the inner fender liner to the point that it cut the wire and broke the connection.
View 3 Replies2004 f250 wipers and fluid not working Done the usual stuff checked the fuses in the cab and the 15amp fuse is good and the 30 amp fuse is good. Is there something under the hood i should look at?
View 3 RepliesI have a 2003 F250 Lariat 6.0L Crew Cab. My wipers, radio and power windows don't work. I have painstakingly checked every one of the fuses to see if there was one or more blown. All were OK.
I removed the fuse panel under the dash and have disassembled it to look for obvious clues, burnt wires/heat damage etc. but everything looks fine. Have pushed all of the fuses in to make sure they were seated properly. No joy.
I recently replaced one of the back windows in my truck and had to detach the rear dome light and I remember one of the wires sparking. Where to start diagnosing this problem?
My 01 F-250's wipers would not shut off. As soon as the key was turned on they would come on. No delay but high and low only. Had to pull the fuse to drive it. I replaced the multi function switch as well as the relay with no fix. I did some reading on this problem and it is related to the "park" switch in the wiper motor itself. I took the black plastic cover off the motor which reveals the worm gear driving the plastic gear which acts as the switch.
The contacts for this switch are hard to get to as they are on the backside. I blew compressed air into every little crevice and removed most of the grease. I regreased and put it back together. Sure enough the wipers work just fine now. I am assuming the compressed air trick may be only temporary. Need to reveal the contacts for the park motor switch without destroying the plastic housing?
I am having some issues with my 2003 f250 6.0l 4x4. I cannot get the 4x4 to engage. There are no lights on the dash and no power to the switch other than the light. It doesn't matter if I have the hubs in lock or auto. It just seems like i have no power to the system. I have check all the fuses and they all check fine. I also check the transfer case motor and it seemed fine. I must be missing something. This truck is worthless without 4x4.
View 14 Replies03 F250. 5.4 2v ... I purchased it a month ago.
Squeak under the hood. It appeared to squeak in relation to the movement of the tensioner......simple right? Replaced Tensioner and Belt..... Still squeaking.
AC not working at all. Compressor never kicking on.....replaced compressor, accumulator, and orifice tube. AC works now!.....squeak still there....
Notice fan wobbling.....shut truck off.....fan clutch shot... replaced....STILL SQUEAKING!!
Obvious answer....sound still on that side of the engine....Idler pulley....I just replaced it and the dang truck is still squeaking!!!!!!!!!
All that's left is the harmonic balancer, alternator, and power steering pump.......What could it be?
Love my 03 lariat Super Duty, King Ranch. Just found out 4 wheel drive is not working. Checked fuses, next going to look at the vacuum system, make sure its working. New to the Diesels but going to work at it and learn at the same time. 2003 F-250 4x4 ....
View 5 Replies1999 F250 5.4l base work truck. My problem is wipers, washer do not function. It all started with my wipers staying on. I removed the fuse to stop them. When i put it back in nothing. I have bench tested all relays, checked fuses, put in a new mfs, put in a new/used gem, checked all wiring i can seem to find, refreshed grounds etc. I am starting to lose my mind with this thing.
I have gone through all of section A and B of these tests [URL] .... except for the NGS scan tool.
Tonight checked the pins at the central junction box relays to see what was going on. This is where things got interesting. i have constant power at pin 5 of the run/park relay. if i jump this to pin 3 the wipers run. Pin 5 of hi/lo and washer show no voltage, however show continuity to ground. pin 5 of run/park also shows continuity to ground.
With the key on I have 12v at pin 1 of the hi/lo, run/park, and washer sockets. when cycled through the switches show i have continuity to ground on pin 2 of all sockets as they should. However, when relays are in place they do not "click" over.
What am I missing here? As much as I'd hate to do it, I may end up just throwing a switch in to "jump" the run park relay for temporary single speed wipers.
2009 F250 lariat. While driving down the highway my wipers came on when stalk was in the off position. They would not shut off. Had to remove the relay to get them to shut off. Also, during middle of a sunny day the headlights would temporarily come on and shut off when it was in the automatic position. They would not come on if I put it in the off position though. Since both the wipers and high beams are part of the multifunction switch is it likely that the switch has gone bad vs. a more major issue with the computers. No other issues identified.
View 1 RepliesMy overhead display quit working earlier this week. The truck has 120k miles. Is this display on it's own fuse? I only used it for the outside temperature readout but I would really like to get it working again.
View 3 RepliesI have a 2003 F250, 4x4, 5.4L and today my fuel gauge stopped working. I don't know if it had anything to do with a stall, I was on an exit ramp and the truck cut off, I quickly restarted and no issues after that. Other than the fuel gauge not working at this point.
I looked at the fuse panel diagram and there is no fuse for just the fuel gauge. The only thing I see is #35, instrument cluster. The rest of my instruments are working, so what else would cause the fuel gauge to stop working? It had a little over a half of a tank before the stall, after the stall it went down to less than half. I filled up shortly later and it's just stuck at less than half.
I have a 2003 F250 Super Duty 5.4 crew cab. Cruise light comes on when engaged but does not work. I did some research on why its not working checked wiring at the throttle body it seemed ok, Fuse is ok. Also did the self test and everything passed with just one flash but cruise still does not work. I read about many problems with the brake pressure switch but would it pass the self test if that pressure switch was bad? Also what should a switch cost. Local dealer wanted $125.00 for a new one and I have read where they cost around $15.00 - $20.00.
View 12 RepliesI have a 2008 f250 with 6.4. Was sitting my truck with key on and motor off listening to radio on lunch and my wipers came on by themselves. Switch was in off position and we're in slow speed. If I turn switch they wouldn't change speed til high position. Turned key off and back on and they came on still. Pulled 30 amp fuse in battery junction box to shut them off.
View 3 RepliesMy windshield wipers aren't working. I can hear the relay click and I've checked the fuse. I found this ground wire, what it goes to?
View 1 RepliesI have a 7.3l 02 f450. The wipers won't work on any low speeds and only on the fastest will they work. And if you switch it from the fastest to any other speeds, the wipers stop right where they are.
View 1 Replies I was driving my truck and my power windows quite working I figured it was a fuse so I wasn't to excited about it I stopped and unloaded some scrap metal and then when I started my truck back up I couldn't shift it out of park unless I unplugged the brake pedal sensor or turned the key just out of the off position then shifted to neutral then started then I could put it in gear and go so I got home and started looking checked all my fuses all good then I realize the windshield wipers are not working either and the door beeper, if you have your keys in the ignition also isn't working the horn, isn't working the lights on the window and lock switches isn't working either so I'm kinda lost now gonna barrow a relay tester in the am but I'm kinda thinking maybe the computer ?? For all this to happen at one to,e doesn't make any sense to me that's a lot to all go in one shot it makes more sense to me
No horn
No power windows
No accessory lights on the window and lock switches
No wipers
No buzzer/beeper (like when you open the door and leave the keys in the ignition
Won't shift out of park without doing it with the engine off or the brake pedal position sensor unplugged
I've gone thru with a test light and got power to the fuses for everything but still nothing
I'm having trouble with my '99 F-350 7.3L 4X4. One day, my power windows, cruise, dome light, horn, wipers, and 4 wheel drive stopped working. After checking all of the fuses, I have found no bad ones.
View 3 Replies2002 F250 SD 4x4 crew cab, v10. 4x4 not working. Replaced switch on dash, not the problem. Some of told me it was the vacuum control module. Not sure where to start.
View 4 Replies1999, F250, SD, v10, Auto, 4x4.
My light on the overdrive is not coming on and the overdrive does not seem to be working. I had a new transmission installed a few weeks back. Wasn't working prior to this.
2000 f250 7.3. Today I tried using the 4x4 and no light or anything. Here is what i have tried so far. Swapped the relays and also swapped them with the towing relays with no change. Not getting any voltage to the t-case shift motor at the selector switch testing between pins 2 and 3 there is 4.3 volts with switch in 2wd 2.4 volts at 4 high and 1.09 volts at 4 low. Where to go from here? it worked fine 3 days ago.
View 2 RepliesI have a 2008 Ford F250 with 6.4. Having alot of problems with the 4X4. Went to put the truck in 4 wheel drive one day and noticed the light on the dash never came on to engage 4X4. Of course we had a big snow storm coming and I didn't have 4 wheel drive. I drove the truck across town and decided to just try 4x4 again and it worked that time. I got the light on the dash and could hear the transfer case shift motor engage. Came out a little later and tried it and it wasn't working again. Took truck to shop where they replaced transfer case shift motor with a remaned motor from oriellys.
4x4 worked for a few weeks then just started doing the same thing again. We thought maybe that motor had problems also so had it replaced too. Truck is still doing the same stuff. Sometimes it works sometimes it doesn't. Figured out that if its not working and I leave it in 4x4 and unhook power to shift motor then plug it back in it will engage 4x4. I've seen some post on here but sounds like everyone i've seen their motor just stops and doesn't work at all.