My 2003 Ford F250 V10 seems to have a vibration, sometimes at all speeds and sometimes at freeway speeds. I replaced front hub assemblies and ball joints and rear calipers last year. When braking i have a vibration in rear as well, which I think is from uneven rotor but can it be causing my vibration? Also sometimes I can smell hot brakes from the rear.
View 2 RepliesI have an '04 EX with 6.0. When braking at highway speeds the rear end shudders until I get the truck slowed down some. Around town speeds of 45 or less the problem is almost non-existent. It almost seems to be hydraulic instead of pads/rotor issue. Wouldn't a warped rotor show up at slower speeds as well? I have some good mechanics around, but have never found a great brake shop that I can trust. Go in needing pads and they try and upsell saying this or that is going out.
View 9 RepliesI have a 02' 250 4x4 with 250000 miles on it. While driving between 55 to 65 mph there is a roar and vibration that seems to be coming from the rear. I have about 35% tire tread left and have had the rear tires balanced and it still does it. Having issues with drive shafts unbalanced or rear ends?? I am not sure where to start....
View 1 RepliesI have an '03 F250 Super Cab, 7.3L PSD, 4WD. I've started getting a large vibration between 40 and 60 mph. Started after driving on the PA highways towing a trailer with a car and hitting several deep pot holes.
I have had the wheels balanced, rotated, balanced a second time by a different shop and had them perform an alignment - Still No change.
The garage I took it to said the hubs were shot so I had them replaced - supposedly with Moog, lifetime warranty hubs. Still - No Change.
The tie rods and steering linkages are a year old, so unless something was damaged (visually, they look good, and feel tight) it probably isn't them.
I replaced the ball joints around 80,000 miles and now the truck has 155,000 miles. They appear to be ok, with maybe just a little movement in the Passenger side upper.
If there is any movement at all in the ball joint, will it cause a vibration?
I plan to rotate my full size spare through all 4 corners this weekend to eliminate the possibility of a bent rim.
I have another set of ball joints and seals on order which should arrive next week. Probably next weekend's project.
I noticed a moaning from the front end a few weeks back and it seems to be slowly getting a little worse. It is only noticeable when I'm accelerating or maintain speed, but as soon as I let off the accelerator and start to decelerate, it goes away. Sometimes, when the truck hasn't been driven for at least a couple hours, I pull away and there is a really noticeable sort of "clunk clunk clunk" but then it goes away and it just moans. I can also hear some noise from the front end at highway speeds, but of course it is hard to hear much else other than engine and road noise from the cab. It's a 2003 F250 with a 7.3 and four wheel drive.
View 8 RepliesI have a bad wobble/vibration coming from front end i think i replaced hub locking hubs u joints truck dont feel safe at all took it to ford they say its normal no way its not just starting doing it few month feels like the 4x4 is in use when hitting bumps when driving if you go slight left or right it seems too make act up more.
View 2 Replies2003 f250 crewcab 6.0 auto 4x4. I all of a sudden started feeling a vibration under the truck near the back when I accelerate and when I let off the gas no other time. No noises or clanking just vibration. I can wiggle the driveshaft inside the carrier bearing do you think that could be it or is it the rear end.
View 14 Replies2003 in sig. when going around corners slow I can feel and hear a chatter or vibration coming from what I think is the rear end. I am running amsoil 75/140 in it and added some friction modifier. Do my clutches are shot and making noise or do I need to add more friction modifier ?
View 7 Replies2004 6.0L Excursion Limited 4x4.
I recently developed a "rumble" with vibration while braking. I describe it as a rumble because I associate it to a similar sound, cadence, and feeling as if you were slowing down on the rumble strips you find on the side of the highway.
It is mostly only noticeable at lower speeds. I know the sound and feeling of warped rotors, but this seems different. If it makes any difference, one issue I've been dealing with is that the front transfer case does not release when 4x4 is off and hubs are in AUTO.
My 2003 F250 6.0 pulls to the right when driving at any speed. In order to keep it going straight the steering wheel must be slightly tilted to the left, not much but a little. When the brakes are applied hard it will go to the left slightly if you are not holding the wheel good. Neither of these are terrible, just a nuisance. I'm worried about uneven tire wear too. One front wheel bearing was replaced a few weeks ago. It had this problem before that and still does after. Does this sound like an alignment or maybe something more?
View 13 Replies2003 F250 V10 4x4. I have a rear brake sticking so I assume I have to replace the calipers. Which brand should I go with?
View 2 RepliesI'm having trouble finding the source of a vibration in the front end if my 1999 f350 super duty 4x4. The vibration is felt all the time but worse when under 40mph, while braking, and especially when turning.
I have replaced the rotors and brakes, tie rods and Drag links since the issue started but no change. In the vibration. What should I check next?
New, 2 month old 2015 CC, gas 4x4 with standard bed. At 50-55 I have a rolling vibration, or it can even be explained as a slight growl. Seems worse since I upgraded to 285/75/18 Toyo AT's and new wheels. If i speed up to about 60, goes away. If I pop it down to 5th gear, it seems to go away, however, I need to try this a few more times to make certain.
View 9 RepliesI am yet another sufferer of the 40mph vibration syndrome I commonly read about on this site. I have had my 2006 f350 club cab sd to the dealership about 7 times for this, and now am being told it is a normal characteristic of this truck. They have replaced wheels, tires, vibration machine analyzed, put on a vibration damper, etc., but nothing fixes the problem. It has done it since the day I drove it home.
How many of you out there are upset about their super duty that jumps up and down at certain speeds? Lately, my dealership has had my truck more than me. From the amount of posts I see about this problem, I am certainly not alone. Ford is now trying to brush me under the carpet, yet I have a truck with a built in gyrator that is totally unacceptable. The truck now has about 20,000 miles of bouncy misery on it, and it isn't getting better.
Two weeks ago did a road trip to NH from RI and i heard a slight dragging only at low speed (10-15mph) in my left rear tire. figured the caliber was dragging a little, it was. Before arriving in NH the brake light came on. Long story short i get back to RI and the left side noise gets worse and starts to lock up. I finally replace the rotor which was warped, pads, and caliper which was bad.
Was driving it same day and still here the same dragging and screeching noise and the brake light is still on. On my way home the left side locked up at low speed without hitting breaks and slid the truck, mid you all parts are new on that side. I am not sure what it could be at this point something in side the axle?
Here's my problem while replacing brake pads i found that my axle has leaked fluid on the pss,side rear rotor and all over .. I been looking for any info on repairing it myself . I found Everything for every other truck just not for this truck.
It's 2003 F-250 w/5.4L all Stock rear axle has 12 bolts and gears are 7.73 ... I believe its a Dana 60. No tags or markings on the Axle to go by..
I live in the Freak-en woods here so i like to order all the right parts once and do over the weekend .. its my only ride so once apart im stuck here.... I did check the Vent Tube its fine..
So I've put about 1000 miles on my 03 F250 since buying it, and just the other day it's started leaking from the rear of the passenger head gasket. Enough to drip on the driveway and exhaust, and have some exhaust smell. 126,000 miles, 5.4
I've checked with my local ford dealer, and It also needs passenger exhaust manifold and studs, so the dealer price to tack that on would be a whole lot more too since there are already a couple studs broke. It would be best to get it done when the head is pulled.
I've checked with several local mechanics, and none of them are interested in pulling the head on this engine. That has me concerned about doing it myself too..especially since it fits in my garage with only a few inches to spare..
I made a bone head mistake and crunched the steel brake line between the rear axle and the passenger side sway bar mount. Truck is a 2003 F-250 with a 7.3. I would like to go to the auto parts store, get bulk steel brake line and bend it myself. But, I don't know what size the line is or what size the fittings are. Whatare the sizes???
View 3 RepliesWhen braking the truck shakes terribly, enough to toss a drink out of the cup holder almost. Sometimes there is a slight feeling in the peddle but not always. The shudder feels like it is timed with each revolution of the wheels.
It developed from a perfectly stopping truck over the course of maybe a month. I don't drive the truck that much either.
Things I have checked:
1, all u-joints, they all look and feel good, no play or slop in them
2, air pressure in all tires, even rotated them, no effect
3, brakes-front and back all looked good but I went ahead and replaced front pads and rotors, cleaned caliper pins, zero effect.
4, shudder exists whether in gear and slowing or in neutral, 2wd and 4wd
What the heck else is there to check? My first thought was, front brakes/warped rotors, but after pulling them apart there was so much life left on the rotors and pads and replacing all that with new did nothing! Could bad back brakes cause this much of a shudder? They look fine as well.
So yesterday I drove across town and back to pick up a piece of lawn equipment. About a 30 min hwy drive each way. On the way there I was in stop and go traffic for about 15mins and noticed toward the end the truck would pull hard to the right when stopping hard and sudden. I figure it was my steering. Been having issues with horrible steering since my last alignment and adjusting the caster. Truck wanders, steering feels loose, will not fully recenter, and feels like it binds then releases toward center position. That's a different issue, I assume. I stop on the way to get some cash and everything is normal. Pick up the equipment and drive back. When coming to a stop the truck will pull towards the right and when I suddenly stop it now pulls to the left.
I get home and get out and smell something burning and hot. Grabbed my IR thermometer and hit both front wheels. Passenger is 150f brake rotor is 175f, drive is 280f brake rotor is 580f. So im assuming my caliper seized up or started to stick. I plan to jack up the front and look at the hubs and calipers. Any other test I can do to narrow down the culprit. I am thinking the hoses may be collapsing especially since I had to disconnect and flip them during the lift. Just weird that the hard pull would switch sides if only the drivers was sticking. Could my bad steering and brake issue be related? I have also noticed my braking power has dropped recently. Brake fluid looks good but power steering smells like brake fluid and is orange.
Pulled the tire when I got home today. A little resistance when spinning by hand, more than there should be. Pulled the caliper and greased the slides. Found out my hub is bad so those are on the short list now. Reassembled and had my wife hit the brakes while I spun the tire. Progressively got harder and harder to spin. Was looking at the brake hoses, how much should they move and ''shrink'' when the brakes are applied? Also if I hit the brakes repeatedly while rolling down my drive way the pedal gets harder and the truck doesn't want to stop and the pedal will slowly push all the way to the floor. Now I am just lost at what is causing my braking issue.
I have an 05 F250 Super Duty 6.0 V8 Turbo Diesel. This is my first diesel so don't know my way around it too much yet. I just don't know what could cause this problem. It sounds like a faulty sensor to me. But no engine light has come on. My oil pressure drops down to in the red zone when I brake while driving, then once I return to driving again it returns to the normal pressure. It's almost as if it has something to do with the tilt of the vehicle.
View 8 Replies