Ford Super Duty (1999-2016) :: 2003 F250 - Pedal Slowly Go To The Floor When Hold Down Brake For Long
Nov 5, 2013
I don't know what's going on maybe some body can shed a little light on this. If you hold the brake pedal down for a long period of time you can feel the pedal slowly go to the floor. So no problem I'll change the master cylinder bleed everything brand new fluid. Don't drive it much we let the sister in law drive it we'll I jump back into it the other day to go to Home Depot and once again I notice it still does it. Could the hydra brake booster be bleeding by or what's else could be causing this it's driving me insane. I really can't imagine the hydra booster causing a problem but it's new to me. I was thinking about bleeding the brakes again thinking there maybe there's air but I have run 2 bottles of brake fluid through how much more??
View 8 Replies
Advertisement
The other day I got in my truck and started down the driveway when I realized I had no brakes, I slowly backed up and parked it. I haven't driven the truck for approx. 2 weeks and it seemed fine then. The master cylinder is full, there are no signs of leakage from wheel cylinders or lines. Today I unscrewed the left front zert and no fluid came out. My pedal goes all the way to the floor.... Whats going on, and if its a easy fix?
View 14 Replies
I took delivery last week of a new 2012 F250 with a 6.7 Power Stroke Diesel. This is my third F250 with a Power Stroke Diesel. My first one was a 1997 w/7.3 PSD and my last one was 2001 w/7.3 PSD which I traded in for the 2012.
Now for my problem. The brakes seem spongy to me. When I am applying the brakes I get what seems like a longer than normal pedal travel (to me anyway) and soft. The braking isn't as good as my last two F250's. If I pump the brakes, the brake pedal firms up and the braking really improves. I have not contacted my dealer yet.
View 14 Replies
I was driving, Iput the brakes on then suddenly I heard a loud bang and brake pedal went all the way to the floor. I knew there was something wrong with the brakes, parked went and checked the passenger side rear brake caliper was ripped off which made a hole through my rim and also ripped off the brake lines. I need to get the part but I don't know what its called. See the pictures....
View 12 Replies
First, I am fortunate that I was only going 25 mph when some turned in front of me causing me to slam on the brakes. The pedal went to the floor, but did slow the truck enough to miss the jerk. Had I been on the highway, it would have been very bad.
Anyway, what I found is still hard for me to believe for two reasons. It find it hard to believe it failed, but more important that I am getting the last national inventory of 2 of the 3 lines in this picture (according to my Ford dealer).
The three lines are almost directly under the front end of the master cylinder between the block and frame. These are as I found them. The larger one goes to the rear feeding both rear brakes while the two smaller run to the front brakes. The spring looking part below is just a plastic protector. The line which failed goes to the front left.
I think anyone with a 2005 SuperDuty which uses the same or similar parts should take a very close look at the flex sections. The parts I have ordered are: 6C3Z-2B523-BA, 6C3Z-2263-BA, and 6C3Z-2264-BA (rear, right, and left).
How long a manufacture is required to maintain inventory? I thought 7 years, but someone suggested 17. I'm at 8 years, but I would have expected more than 1 each of the fronts to be available. Do they changed parts on the '06 or '07?
My 350 spent 2 winters in the Chicago area and has been resting in Florida since 2006. No work was done in this area, but the closest work was the main fuel pump (frame mounted) replaced 2 years ago, but that is almost 2 feet to the rear.
View 14 Replies
Pulled out of street this morning and as I was shifting into 3rd my clutch pedal went straight to the floor boards. I was able to keep it in 2nd gear and get it back to my driveway . The pedal will only go straight to floor or goes straight up too the bottom of dash board. It's spring loaded. Am I dealing with a linkage issue?. I had clutch as I pulled out of my driveway and stopped go at the stop sign. Plus I was able to drive it back too my house with the pedal on the floor boards. Where I should look first?
View 4 Replies
My stock 2009 ford f250xl 4x4 with a 5.4 and 6 speed has been giving me a weird sound lately started about a month ago and only happens on a cold start situation meaning if it sits over night it will do the sound. the sound goes away after 3-5 min of warm up in my driveway, the sound happens when i push the clutch pedal to the floor. it has no pronounced abnormal sounds through out the rest of the day when its hot which perplexes me, check out the vid on my u tube site for a sound of it.
MAH00111 - YouTube
MAH00115 - YouTube
View 7 Replies
Today I was going to launch my new boat and when I backed down the ramp, the brake went to the floor almost sinking the truck. Long story short, the brake line that runs along the frame to the rear brakes rusted through at a bend that I couldn't see. Seems the line is about 8 feet long. What I'd like to know is can I replace it without dropping the fuel tank which of course I just filled yesterday and can I obtain one at a ford dealer or will I have to order one. My truck is my only transportation.
View 1 Replies
I don't know whats up with my new truck, its a 04 f250 scsb, 4x4, 5.4l with 61k orig miles on it. Truck will stop on a dime, has NO pedal sinking, but it takes about 3/4 of the pedals travel to apply pressure to the pads and have the truck stop, sometimes if I push the pedal down then let up and push it again the pedal wont travel as far, I just flushed the system today, no air in the lines, is there a bleeder on the abs? truck has 4 wheel abs...
View 14 Replies
I have a 2000 SCrew KR F150. A couple of weeks ago I noticed the brake pedal was slowly going to the floor while at a red light. I pulled over and popped the hood checked the fluid reservoir. It was full, so obviously no wheel cylinder issues or fluid loss. I haven't had a chance to tear into it yet.
View 14 Replies
I noticed last week that my brake pedal seemed more spongy than usual. The next day the pedal would go down about half way to the floor before I had pressure. And then the next day the pedal would go straight to the floor. Pedal comes back up once released. I still have brakes pressure about an inch before the pedal bottoms out. Its been like this a couple days now. The vaccum pump works fine. I'm gunna try bleeding the brakes on it tomorrow.
View 5 Replies
I'm having issue with my brake lights. Checked for voltage and nothing. Checked the fuses under the dash. Checked the brake pedal switch and have power going out when the pedal is pressed. Is there a relay or something somewhere else? 1999 f250 7.3 superduty....
View 2 Replies
I just bought my first Ford. Its a 2003 F250 SD with 5.4L, 5 speed manual, extended cab, 2WD. The truck is experiencing intermittent problems with the clutch pedal.
If I depress the clutch pedal for a long time, then sometimes it does not retract all the way. It does this, for example, when I am at a traffic light waiting for the next opportunity to make a left hand turn.
The truck runs and operates as it should even when this does happen. The easy response is to place your toes under the clutch pedal and pull it aft to its completely released position.
The master and slave cylinder and the booster spring attached to the clutch pedal assembly have been replaced and this condition still continues.
View 2 Replies
I have a 1992 F250 7.3 diesel 4x4 My brakes wont hold pressure I replaced master cylinder and calipers had the system pressure bled. I don't have any fluid lose and vacuum is good. Can the proportioning valve let fluid bypass, or the rear anti-lock braking system valve let fluid to bypass.
View 14 Replies
I have 03 f250 v10. just replaced the engine and got everything all connected and started it up and it idles great...the problem is that when you press the gas pedal it starts to drive but then it looses power and acts like its missing. cant get it to go 30 mph. While keeping it floored eventually it gets up to 2000 rpm and then starts to pick up speed.
View 14 Replies
While in Tow/Haul with my 5th wheel when slowing down probably at 5 or 10 mph the last downshift is very hard and the brake pedal gets real soft until full stop. Afterwards the brake pedal is firm. Tow/Haul without the trailer is fine. It's an '06 F250 Supercrew 4x4.
View 6 Replies
I have a 06 f360 PSD 6 speed. On a road trip and the clutch pedal is getting very close to the floor. No Slippage but the longer I leave the pedal pressed the worse it gets. Are there any good descriptions how the clutch in this truck works?? Slave cyl??
View 14 Replies
Can get up to speed about 55-60 in my 2003 f250 6.0 4x4 truck and hit the brakes hard and the pedal gets hard almost like you cut the truck off and the truck doesn't stop well I can let off the pedal and hit it again hard and it works like it should. Also when it does this the power steering doesn't work. I was on an exit ramp and almost wrecked when I exited off the interstate I hit the brake pretty hard and couldn't steer I let off the brakes then hit them again and it worked fine and so did my steering. It would seem that the two are connected somehow. What's wrong?
View 2 Replies
I Have a 1999 f250 7.3 diesel with the zf5 manual transmission and to shift gears I need to push the clutch all the way to the floor. Could this possibly be the slave and master cylinder or is it the clutch?
View 14 Replies
I have a 2009 f 250 5.4 v8 trition motor my coil packs are slowly failing. I want to replace all 8 of them. Which coils and plugs I am going to need. I guess I'll replace the plugs also, how are the accel coil packs and ngk plugs....
View 1 Replies
Had the rear passeneger side brake line burst today in rush hour traffic ..wasn't much fun. Is it a easy to do it yourself deal ...it is a 2003 f250 v10 triton .
View 1 Replies
