Ford Super Duty (1999-2016) :: 2003 F250 - Oil Leaking From Back Of Passenger Head / Overflow Started Bubbling Over
Mar 1, 2016
I have a 03 250 gas 5.4 trying to find out the cooling system problem. I've found what I've read to be common oil leaking from back of passenger head. I had never noticed this before but it started very slight now overflow started bubbling over.
There is no coolant in oil no white smoke. My cooling system leak is just head gasket and gasket change could solve the problem or should I did deeper?
View 9 Replies
Advertisement
So I've put about 1000 miles on my 03 F250 since buying it, and just the other day it's started leaking from the rear of the passenger head gasket. Enough to drip on the driveway and exhaust, and have some exhaust smell. 126,000 miles, 5.4
I've checked with my local ford dealer, and It also needs passenger exhaust manifold and studs, so the dealer price to tack that on would be a whole lot more too since there are already a couple studs broke. It would be best to get it done when the head is pulled.
I've checked with several local mechanics, and none of them are interested in pulling the head on this engine. That has me concerned about doing it myself too..especially since it fits in my garage with only a few inches to spare..
View 14 Replies
This morning while driving cold a fuel leak started on my truck it's a very heavy leak wondering what are the most common leaks on an 2003 F250 6.0L are so I can start there.
View 3 Replies
Have my oil leaking-passenger side head gasket replaced (along with the drivers side for preventative measures).
To ease my mind at such an expensive repair on a truck I just recently bought, I was wondering what else gets replaced with this repair.
Obviously the head gaskets along with head studs, coolant and oil, but anything else? valve cover gaskets? intake gasket?
View 14 Replies
Here's my problem while replacing brake pads i found that my axle has leaked fluid on the pss,side rear rotor and all over .. I been looking for any info on repairing it myself . I found Everything for every other truck just not for this truck.
It's 2003 F-250 w/5.4L all Stock rear axle has 12 bolts and gears are 7.73 ... I believe its a Dana 60. No tags or markings on the Axle to go by..
I live in the Freak-en woods here so i like to order all the right parts once and do over the weekend .. its my only ride so once apart im stuck here.... I did check the Vent Tube its fine..
View 14 Replies
I have a 2005 f250 5.4 no mods. its got 120k and needs a wake up. the passengers side exhaust manifold is leaking to the point of fixing and would like to get some input before the big purchase. my question is, headers or new manifold, and what brands is preferred for both I really don't prefer one or the other i just want the best fix really. Changing coil pack and getting more performance out of them and if so what brand. I would like a boost in lower end acceleration and throttle response, like a programmer or such. and if so what brand once again.
View 10 Replies
After replacing most of the underside of my Super Duty, Complete front end, backing plates, brakes, rotors and shocks, I have a misfire code on cylinder #4. I replaced the plugs, cleaned the MAS and filter and rotated the coil to cylinder #1. Still have a misfire on #4 and noticed the coolant slightly low and some condensation on the oil cap. Could this be the intake gasket? My mechanic is away for 2 weeks and I think the price at the dealer will kill me. I have 63K on the truck, don't tow and plow mostly family members. It's getting a little rusty but is still in good shape.
View 13 Replies
2003 f250 5.4 86000 miles. When I start the truck, "especially after it sits a day or more" it starts to fast "Rushes". Like the gas pedal is all the way to the floor. I have taken it to the Ford dealer and they say they can find nothing wrong. They say all fords start up fast but I know this cannot be right. If I start it and let it run awhile then start it again it starts much slower. It only rushes like that a second or two and slows down. Today I noticed that when it started all the gauges pegged out. The speed indicator went up past 100mph sitting still in park. Then they all dropped down to zero then back to where they should be.
View 3 Replies
I'd like to replace the back bench seats with something that has a headrest. Can I swap out the benchseat from a 2004 model and place it in my 2003 model?
View 4 Replies
2003 f250 crewcab 6.0 auto 4x4. I all of a sudden started feeling a vibration under the truck near the back when I accelerate and when I let off the gas no other time. No noises or clanking just vibration. I can wiggle the driveshaft inside the carrier bearing do you think that could be it or is it the rear end.
View 14 Replies
To all those folks that said I had a head gasket putting pressure into my cooling system and causing it to overheat, you were right. It is a 2003 F250 with 80000 5.4 l. I have had to replace mexhaust manifold bolts on left side (horrible job, couldn't get one out). Back fenders are rusted out, under the extended cab rusted, doors are rusting at the bottom. My friend/mechanic said it was time to get rid of it. I don't really have thousands of $$ for a different one, but also, replacing the head gaskets are in the thousands for a repair bill. I have looked at used 2008 250 4 door and they are 20000+++ sheesh, but a new one is out of the question. Do I get the gasket situation repaired?
It does not act up all the time, some times it never overheats, sometimes it will. Somewhat infrequent ( I had one mechanic look at it and he tried 3 different times, and it did not overheat. Temp gage will peg, coolant resevior will overflow, but is not hot (100 degrees). I dont have the really have the money to put into a newer model, but I am worried about being nickeled and dimed to death after dumping a couple of thousand into a head gasket, plus I suppose I need to have the other side manifold gasket/bolts checked too. It seems like low miles to be having issues, yes I realize all will rust, but this year, as evidnet in our area, was really suspect-able to rust.
Not worried about the body, is it worth it to spend 2500 for head gasket repair, or trade up a couple of years, less miles, etc. My worry is, I already had to fix 1 exhaust manifold gasket, know head gasket to fix a cooling issue, do I cut my losses and move to another truck, or spend the money for repairs. I don't really have money for either but want to make a good decision. Truck has not been abused and has been serviced as scheduled. Had to put on new brakes and rotors, as would expect, and ball joints too. Oil looks fine, no contamination, and coolant is clear. Will the head gasket get worse? As I said before, it is intermittent, but I don't trust it for long trips.
View 9 Replies
My mechanic cannot figure it out nor can a Ford mechanic. About every one to two weeks, only in the morning, after I drive about a half mile it starts running rough and stalls at idle. It behaves like it is flooding out. When I can get it started black smoke pours out until it clears. I can hold it above 2000 rpm but, as I lower the revs, it starts stalling again until it stops. I've tried blowing it out on a long stretch but at normal speed it does it again. After repeating this several times it suddenly runs right and won't happen again for a couple weeks, the longest being four weeks. I thought it might be the remote start but that theory was busted. I've searched here and in other sites and replaced the IAC but it still did it. Replacing the O2 sensors did not work. I don't want to keep throwing parts at it.
'03 F250 FX4, 5.4 gas....
View 14 Replies
03 F250. Passenger window is stuck up. When I have the door panel off, I can feel the motor trying to move up. Won't go down at all. When I connect test light to the plug, it lights up correctly for both up and down. Thought maybe it was the motor so I got a new one but it only tries to go one way. It's like the switch isn't sending the signal for the window to go down even though the plug appears to be getting the correct signal.
I took apart the driver's side switch and nothing looks crimped, bent, etc. From some reading, it sounds like possibly the regulator is bad, does that somehow send a signal back to the switch? Is there a relay or something that could be bad? I find it odd that test light seems to work but when connected to a motor, it doesn't.
View 1 Replies
We have a lot of snow and a lot of ice up here at the moment and my 2003 ford F-250 SC Fx4 isn't performing so well. The truck is stock other than a pair of 285/16R BFG A/T's
I have been noticing that my rear tires will spin while trying to go up hill on some ice or snow covered areas and my front tires just sit still while in 4x4 or 4x4 low. In the case I just described I remain stuck in place until the rear tires can get a grip then I continue up hill. I don't understand why my front tires are not spinning as well, to me this seems just like 2 wheel drive not 4x4. I have been using ESOF most of the time. I have mentioned in other threads that I do plan on upgrading to warn premium hubs, but I am wondering if its that my truck isnt actually shifting into 4x4 or if there is a reason why even in 4x4 my rear tires would spin while my front tires do not?
I am confused because when I shift on the fly while driving I can feel the 4x4 kick in because it just feels different than driving with 2 wheel drive, but then something like I described will happen and I start second guessing myself. What might be happening? It's not that I am opposed to switching to the warn premium hubs, but is that actually going to fix this issue or is my truck acting normally??
View 13 Replies
I recently purchased a 2003 F-250. The door locks don't work properly, the passenger side will lock the entire truck all 4 door locks actually lock. The unlock on the passenger side does not work and neither does the entire switch in the driver side. I attempted to switch the actual switches from the driver to passenger side thinking that it could be a switch that is broken.
After doing that still only the passenger side would lock and the rest of lock unlock buttons did nothing. I have checked all the fuses in my truck and actually took the door panels off today thinking I might find an obvious problem. I know the actuators are a common problem but because all the locks lock in the vehicle I was thinking it might be something else.
View 1 Replies
I've been trying to figure out what is going on with my '99 F-250 V10, you can check out this thread for the back story
[URL]....
I did a compression check and the results seem inconclusive to me- see image.
Before I did the compression check I started to take the intake manifold off to change the gasket set and it's about 50% done. I'm at a crossroad now. Do you think I should finish switching out the intake gaskets or do you think it's more than likely a head gasket? I would hate to put it back together, it still smoke and have to take the intake and everything else back off to do the head gaskets.
Someone had mentioned a possible small crack in the cylinder wall that is closing up when the engine gets heat in it and obviously doing the intake and cylinder head gaskets would fix it if that's the problem.
View 14 Replies
I have a 2003 F-250 6.0L 2WD and I recently noticed a rattling thumping noise under the front end on the passenger side. I noticed the rattle shortly after I got new tires, which are a hair bigger than the tires I had on it before. I thought it might be my new tires rubbing since they were bigger but then I noticed the rattle when I had my wheel straight and also when not moving at all. I've been driving it for a couple of weeks now with this rattle and I've been able to determine that it rattles most when I am going downhill and turning to the left putting more of the weight of the truck on the front right suspension components.
After reading several threads my first attempt to find the problem lead me to the discovery of a worn sway bar bushing. I thought this was for sure the problem and replaced both bushings and end links. But the rattle didn't go away. Then I thought maybe it was a bad wheel bearing so I replaced the wheel bearings in both front wheels. Still no change. Lastly, I happened to find a loose ABS line in the front right wheel well that was no longer secured and was banging against plastic. I secured that and still no change. All the bushings seem to be in good shape so I am considering taking it to a mechanic since I don't want to just replace everything hoping that it solves the problem piece by piece.
View 12 Replies
I am replacing the head gaskets on a 2006 Ford F250 6.0 .... I have heard that I should replace the head bolts with studs. Do I torque the studs just like the bolts?
View 5 Replies
I just bought myself a 2003 F250 XLT with the V10 in it. Low miles, not beat, 6 speed, very happy with it. I noticed today that there was an inconsistent tapping coming from the passenger side valve cover. I searched online and was pointed towards the PCV baffle. I pulled the breather hose off and stuck my finger in the hole, and the baffle is indeed detached. Now I know that I need to pull the valve cover now to at least remove the baffle; is there anyway to reattach the baffle, or do I need to buy a new valve cover?
View 8 Replies
(The truck is a 05 f250 with a 5.4l). The problem first started out with the engine temperature gauge spiking and then resetting itself when the truck is turned off and then turned back on. If I drove the truck for any distance it would go into limp mode and the CEL would come on. The code was p1299, which is the cylinder head temperature sensor, and I replaced the sensor but no luck. Then the shop and I went through all accessories hooked up and couldn't find a short until I remembered that my prodigy break controller would occasionally read "ol" or "sh" which both readings are from shorts. I tow a enclosed trailer about 85% of the time and the past week I have been towing it with a different 250 and the same break controller without a problem so I have eliminated the trailer. But the shop just said the problem was the controller and unhooked it.
Now the next day it threw the same code with the controller unhooked and the trailer hooked up. after thinking it seemed that it was happening when i accelerated so I took apart the 7 pin and sure enough there was a little water in it, but after driving it around for a little and no code being thrown I hooked my break controller up and it still was showing ol or sh so i believe there is still a short. Also I noticed that my voltage is reading right at 13v instead of the 13.8-14v it was reading before this issue arose. I think I have narrowed it down to the 7 pin harness and/or electrical in the break components, but do not know what would loop back to the temperature sensor.
View 2 Replies
I replaced a rear rusted brake line a couple of years ago. It rusted where the line met the bracket. I'd never done this before but bought a flare (flaring?) tool and fixed it.
This week the longer line that runs down the length of the truck started leaking. It looks like the line was once held in place by a small bracket just in front of the rear wheel but it wasn't in that bracket anymore. I guess it rubbed against the metal and water/sand rusted it out.
A local garage said they'd need to drop the fuel tank and estimated that it would be several hours (and hundreds of dollars) to do the job. It looks like I might be able to cut the old one out and then fish the new line up through there and replace it.
Also, what is the diameter of the line? It is a 2004 F350. I can certainly cut it out first and then take a piece of it to the local auto parts place to get the replacement line.
View 9 Replies
