Ford Super Duty (1999-2016) :: 2003 F250 - How To Replace Back Seats
Aug 22, 2013
I'd like to replace the back bench seats with something that has a headrest. Can I swap out the benchseat from a 2004 model and place it in my 2003 model?
View 4 Replies
Advertisement
I am needing to replace the front hub wheel bearing assemblies on my 03 F250 4x4. I know Ford changed the studs from coarse thread to fine thread in between the 02 and 03 model years. Mine has a build date of 08/02 and I haven't been able to find the exact date they switched over. I'm ordering the parts online and want to get it right the first time.
View 3 Replies
2003 f250 crewcab 6.0 auto 4x4. I all of a sudden started feeling a vibration under the truck near the back when I accelerate and when I let off the gas no other time. No noises or clanking just vibration. I can wiggle the driveshaft inside the carrier bearing do you think that could be it or is it the rear end.
View 14 Replies
We have a lot of snow and a lot of ice up here at the moment and my 2003 ford F-250 SC Fx4 isn't performing so well. The truck is stock other than a pair of 285/16R BFG A/T's
I have been noticing that my rear tires will spin while trying to go up hill on some ice or snow covered areas and my front tires just sit still while in 4x4 or 4x4 low. In the case I just described I remain stuck in place until the rear tires can get a grip then I continue up hill. I don't understand why my front tires are not spinning as well, to me this seems just like 2 wheel drive not 4x4. I have been using ESOF most of the time. I have mentioned in other threads that I do plan on upgrading to warn premium hubs, but I am wondering if its that my truck isnt actually shifting into 4x4 or if there is a reason why even in 4x4 my rear tires would spin while my front tires do not?
I am confused because when I shift on the fly while driving I can feel the 4x4 kick in because it just feels different than driving with 2 wheel drive, but then something like I described will happen and I start second guessing myself. What might be happening? It's not that I am opposed to switching to the warn premium hubs, but is that actually going to fix this issue or is my truck acting normally??
View 13 Replies
2012 f250 diesel Lariat 4dr 4x4. He called me today cause he knows I do all the work on my own F250 diesel. He has heated seats in the back and he said that they turn on by them selves and they won't turn off. He had to actually disconnect the wire harness to get the heating elements to turn off so his wife's friends wouldn't burn their bottoms in the middle of august is Texas.. Any ways, he said both sides are staying on and wouldn't turn off using the switch.
I'm not very familiar with the heated seat wiring, especially for the back seats. I told him their may have been a relay that went bad, but now I"m thinking that they much have a controller or something that is acting up. He said that the front seats are acting normal. Also, he has the touch screen and navigation upgrade as well as auto climate control, not sure if this stuff matters for the back seats though...
View 2 Replies
I have an 2002 F250 super duty that has leather seats. The seats are power but not heated. I bought seats out of a Harley Davidson edition that are electric and heated. They have an extra plug that my truck don't have. How can I make the seat heaters work?
View 4 Replies
I have a 03 250 gas 5.4 trying to find out the cooling system problem. I've found what I've read to be common oil leaking from back of passenger head. I had never noticed this before but it started very slight now overflow started bubbling over.
There is no coolant in oil no white smoke. My cooling system leak is just head gasket and gasket change could solve the problem or should I did deeper?
View 9 Replies
I needed to replace the intake manifold gasket on my 2002 f250 v10. Tore everything apart put the new gasket in which was the same as the old one lyrics to notice something isn't right. I have been driving the truck for over 10 years like this. Is it OK to just continue bolting everything down and go on like this? I am guessing the prior owner 10 plus years ago put the wrong intake on. I keep looking up intakes but they all look just like the one I have. Also that port exposed is on the back passenger side.
View 3 Replies
I have a 2001 F250 Super Duty 5.4 Triton motor with a Transmission Leak. I have drained the Transmission, replaced the Transmission pan gasket and filter. The auto parts store also had me purchase the Torque Converter bearings/seal along with enough transmission fluid and a bottle of Lukas Transmission fix. Do I really need to replace the bearings/seal if I have everything else already ?
View 2 Replies
I have a 02 F250 V10. When I am pulling a trailer and began to travel over 50 MPH the truck feels like its moving left to right almost like its sliding on ice. Its worse the more weight I am pulling. When I am not pulling anything there is no issues. The trailers I am pulling are gooseneck trailers. What would cause this.
View 11 Replies
I have a 2003 F250 5.4L crew cab with the 156"wb. She has just developed a hole in the stock muffler so it will need to be replaced.
I want something that is an easy-fit, has better flow, and maybe better sounding.
View 1 Replies
First tech post for my new truck. I just bought a hold-over but new 2015 F250 XL Supercab 2wd and love the simplicity of no unwanted options. That said, there are two features I am adding. The first is perfectly straightforward, cruise control (swap button cluster and have the function turned on by the dealer). The second is a tiny bit more involved, back-up camera, in mirror display with bluetooth hands-free (I like the simple AM/FM radio because I can work it all with gloves on).
So I basically need three things from the truck and my research has been inconclusive on a couple of things because most of the threads are for 2014 or earlier. I think I can pull switched 12V and ground (pin 1 and 4) plus reverse lights (center, or pin 7) all from the the trailer wiring harness. It appears these are not affected by the canbus load restrictions of other places to tap reverse signal (remember, XL so likely nothing in the overhead console for the auto-dimming rear view mirror). Are there any challenges with this when I do hook up my enclosed trailer or when it is not hooked up regarding the trailer brake controller/anti-sway?
I already found a good youtube video for how to route the wires so I think this is my primary challenge at this point.
View 14 Replies
I bought my first vehicle last October, a '99 F-250 with a 6.8 V10. I later found out (AFTER hauling a big load of rocks in a dump trailer) that one of the bottom leaf springs was broken. So this winter I have been thinking on what I want to do about it when it warms up. This is pretty much on top of the "to do" list for my truck. I did make a thread about putting 1 ton springs under it, but I think I'll just stick with the regular 3/4 ton springs. So now this is where I have another question, and I think this pic will tell some of it:
Now I'm not sure if those rear springs are stock, but that rear end is way the heck up there! The truck itself is not level, the front looks to be correct height, but not the back. A buddy at school and I were talking about a leveling kit for the front. But the more I look at it, I think the rear end should come down. I don't want to get bigger tires, as I just put brand new Transforce AT's on the back and plan to put new ones on the front in the near future.
Another question of mine is, would this have been a truck ordered just for pulling a camper? It has holes for a fifth wheel hitch in the bed, the rear end sits high, and it didn't come with a tow package. The PO told me that he put the receiver hitch on it. I'm fixing up stuff on it one thing at a time. Springs just happen to be next on the list.
View 14 Replies
1999 F-250 LD 5.4... There is a hole on the back of the upper intake manifold, just below the back of the throttle body, is a vacuum hose supposed to be attached here? Have a serious vacuum leak, no coolant loss, no overheating, just had cop's and spark plugs done, now she backfires, stalls and will not stay running, mech. says its an intake gasket but the gasket and lower intake manifold look new.
View 7 Replies
1999 F250 extended cab back doors won't open. The passenger side stopped opening right after I purchased it a few months back (168K miles). I removed the door panels and reached my hand in feeling around. I know the latch releases are activated by cables but cannot figure out how they work. While feeling and pulling on the cables one became dislodged from its holder. The driver's side stopped opening yesterday . Do the cables stretch, break, or what? Or are the holders the issue? Is there an illustration that shows how the cables are run and connected?
View 14 Replies
I've got a 2014 f250 xl super cab and can't for the life of me figure out how to remove the back seat back.
View 2 Replies
I have a 2002 Ford F2 50 that has a diesel leak on the back of the engine. I've already replaced the drain valve that was leaking. Then I noticed that the front of the engine was dry now but the back of the engine still has some pooling With a very small drip off the back of the engine between the transmission housing and engine. Not as bad as it was of course But still a small drip. Where this may be coming from? And how to fix it?
View 4 Replies
I replaced my my front hub assemblies on my 2003 F250, 4x4, about two years ago and my driver side hub is leaking. I first noticed it the other day when I tried to shift into 4 wheel drive and my hubs would not lock in the ESOF system.
I used a vacuum pump and it leaked down pretty fast so I assume the knuckle/axle seal is the culprit.
I plan on ordering these three seals:
Amazon.com: f81z-1s175-hca
I am also noticing another # for the axle seal. It is 3C3Z-3254-CA. Which is correct for my 2003?
Are my questions would I actually need to replace all three? The dust seal is not leaking at the moment. Should I go ahead and replace it anyway?
What type of grease do I need to use the seals? I have some disc brake bearing lithium grease in the cabinet. Will this work or do I need to get a specific type
Lastly, I've seen a post where members have made their seal seating tool out of the galvanized pipe, cap, and a flange. The flange is said to be too large and it would have to be ground down for the right diameter.
View 14 Replies
I have a super duty with the 5.4 in it. it just quit while off road n wouldn't start back up. pulled it back to camp, wiggled wires around cam n crank sensors n it fired up n stalled numerous times then just wouldn't even fire back up. loaded on trailer n brought home, buddy put his tester on there n said there was no rpm reading so I replaced the crank sensor, it fired up n stalls still. wires seem to be good to crank n cam sensors. don't have a manual to tell me what relays are what.
View 11 Replies
Ok truck shut down wouldn't start back. Put fuel filter o. Frame cranks but won't start. Was told has high pressure oil leak in engine?
View 8 Replies
The flashers and blinkers work, the taillights, brake lights and back up lamps do not.
The truck is a 2004 F250 4x4... Checked all fuses. What am I missing?
View 9 Replies