Ford Super Duty (1999-2016) :: 2003 F250 4x4 - Left Rear Caliper Sticking After Replacing
Jan 9, 2017
Two weeks ago did a road trip to NH from RI and i heard a slight dragging only at low speed (10-15mph) in my left rear tire. figured the caliber was dragging a little, it was. Before arriving in NH the brake light came on. Long story short i get back to RI and the left side noise gets worse and starts to lock up. I finally replace the rotor which was warped, pads, and caliper which was bad.
Was driving it same day and still here the same dragging and screeching noise and the brake light is still on. On my way home the left side locked up at low speed without hitting breaks and slid the truck, mid you all parts are new on that side. I am not sure what it could be at this point something in side the axle?
View 2 Replies
Advertisement
I have for the 4th time in a little over a year developed another issue with a rear caliper hanging up last year i ended up replacing both rear calipers with reman. from NAPA. 3 months ago i had to replace the right rear again. Now currently i am having the left rear starting to hang up again. I've done a fluid flush and everything. I'm kind of at a loss. I don't normally have this much trouble with brakes. Some of the symptoms that go along with this are a spongy pedal and inconsistent brake feel just like when you have air in a line.
View 1 Replies
2003 F250 V10 4x4. I have a rear brake sticking so I assume I have to replace the calipers. Which brand should I go with?
View 2 Replies
I just hit a pothole on my way home just now and now my front right caliper is sticking. It happen about 10min from my house. As soon as i hit the pothole I can feel my truck pulling to the right and felt like there was some resistance when i was driving. I got home and peeked my head in the wheel-well and i can smell the brakes burning and smoking a little. How would hitting a pothole cause a caliper to stick. Is there anyway to unstick it or am i gonna have to change that caliper out...
View 8 Replies
I know this has been talked about many times and how to solve the issue but thought I would ask some other questions too. Earlier in the summer, I did grease the slider pins as preventative maintenance. I don't drive my truck all that much and when I used it yesterday, (about 30 minute drive) I came home to burning brake smell. I'm wondering if enough heat would cause the caliper to go bad? Should I just grease the pins again or change out some parts?
View 6 Replies
Took truck out for a ride and stopped for gas. I smelled Brakes and upon inspection found the left rear brake pads were not releasing. Any take on what could be holding it? 2008 F-250.
View 10 Replies
1999 F350 4x4 dually. Replacing brakes front and back. Rotors, Pads, and hoses. On the left front put rotor back on and torqued down hub nuts on rotor. Then caliper mounting bracket wouldn't fit back between mounting bracket and rotor. Loosened the hub nuts on rotor, and fit mounting bracket in place. Then torqued down the hub nuts again, and rotor rubs on mounting bracket and rotor/hub won't turn.
View 2 Replies
My 1999 F250 right rear brake caliper will not release. I replaced the caliper, caliper mounting hardware, pads, rotor, emergency brake pads, and I bled the system. For some reason the right rear remains activated when my foot is not on the brake pedal. The other three wheels appear to be functioning normal.
View 6 Replies
I have 2014 F350, was previous flood damaged, the steering keep sticking when I turn it to the left, not always in the same spot, but sometimes it just locks and will not turn right, needs lots of jiggling and then it release, as I say in different places but always when turning to the left, never when turning to the right. Does this indicate steering gear fault or something else?
View 9 Replies
Having a problem with calipers again/still seems like always. Replaced all calipers twice in 86K miles on a 2000 f250 crew 4x4 because of stuck calipers. Replaced brake hoses and all hard lines in the rear about 2 years ago. My problem now is the left front caliper is not squeezing hard enough to stop the truck evenly. (pulls to the right) The rotor had some rust from sitting and after driving a for a while the rust is not completely gone as you would expect. Replaced caliper bled a couple of times. Caliper looks to be getting pressure enough to bleed and can see it move when brakes applied when engine not running. I don't have experience with Proportioning Valves but do you think that is the problem and how do I fix it?
View 8 Replies
I have a 2002 Ford F250 Superduty with a 7.3 diesel. Brakes started sticking on it. I replaced all the calipers cause the boots were starting to crack but not leaking. All four brakes are still sticking. I can drive a little ways and then the brake peddle feels funny and they start dragging all four. I can loosen the bleeder and brake fluid will spray out and release the brakes for awhile.
View 4 Replies
So I just did my rear brake pads and rotors a few days ago. For the last few months, my e brake hadn't been working well (have to pull it way up, and still weak).
While doing the brakes, I noticed the park brake arm was more or less seized on the left rear. I worked it a bit, and then my park brake worked perfect - 4 or 5 clicks, right on.
Then I noticed it isn't disengaging (brake smoke). I figured the ratcheting mechanism in the piston must be kaput.
So today I got a new (reman) caliper & bracket, installed it, and... still sticking. Cables are fine, the arm is moving fine. I'm now certain that the problem must be hydraulic, but what?
I would think that a master cylinder or booster would cause all the brakes to drag, or at least one axle worth, but that isn't the case. After a short spin on the freeway with little brake use, 3 of the brakes show 40 - 45C or so, and the sticking one shows 150C. (with an infrared thermometer).
During the brake job I noticed the left side was harder to turn in than the right, so I guess that could have been hydraulic back pressure somehow. Didn't seem to notice any damage to the hoses, they look pretty mint. master cylinder still?
I did the rear bearings at the same time. The bearing on the left was bone dry, probably from overheating in the past - I'm sure this POS stuck at some other time too, overheated and lost its grease. right side was fine but I figured might as well do them both.
View 18 Replies
About a year ago, I had my right rear brake caliper lock up on my F350 dually. The shop said it can happen and replaced both rear calipers. Last week I started to hear something from the rear and within less than a a few days, before I could get to a shop the noise increased and when I looked the rotor had been gouged on the right rear.
I cannot see the left rear rotor to compare as the wheels don't line up on that side to see through. So my question is this. Could it be the caliper failure was a symptom and not the cause. Maybe a proportion valve or something that could affect the pressure on that one wheel.
View 11 Replies
I have a 2010 F250 V10 4x4. about every 3-4 times when you start the truck....it seems as though the starter "sticks". If I catch it and shut it off and then turn the key right back it fires up and does not stick. Its as if the gear is staying kicked out into the flywheel. Are we thinking the starter itself? I'm thinking starter...but looking for input before I crawl under it.
View 1 Replies
I just recently purchased my 1999 ford F-250 superduty V8 5.4 5 speed with 144,00 miles and I'm having a issue with the clutch pedal sticking in and then it will pop out after a couple seconds. It will stick more when I come to a light and have my foot on the clutch but the pickup drives fine and there is no slipping of the clutch. I have never experienced this issue before in any rig I've owned. so I'm a little lost at the moment.
View 2 Replies
I have a 2000 f250 4x4 with 4 wheel abs. The front passenger side caliper keeps locking up while I'm driving and won't release and when I hit the brakes it pulls hard to the drivers side. I have put two calipers on the passengers side and put new brake lines on.
View 8 Replies
one of my f350 super duties has had the right rear brake caliper and slider replaced 4 times in less than a year. it has just gone for the fourth time today. i called ford who, after a long phone call, said it could be the metering valve. i have looked everywhere for this valve.....no luck. so i called them back and he said it was part of the HCU. after a few minutes, he finally told me it was also called the ABS module.
my question is..........can i just replace this metering valve or do i have to replace the whole unit?
View 1 Replies
Ok so I think I have sticking calipers on the rear passenger side of my truck, not 100% sure but ill be getting under the truck tomorrow to check. My question is how hard is it to fix this and how long do you think it will take? I have all the right stuff to get the truck jacked up and I have enough money to do this, time is just the issue. It gets dark around 4:30-5:00pm here and I get home from school at 3pm, and have work also but not until saturday this week.
I'd prefer to do this after school if possible because I've stopped driving it so that way I don't wear down my brake rotors and pads for no good reason. I have to drive the work truck that has many of its own issues but its driveable, headlights are very dim due to oxidization and is dangerous to drive in the snow due to the tires (no money to replace right now). How hard and how long this would be? What else it could be shoot! The problem is, it slows down if i let off the gas as if i was breaking, high heat from rear passenger side brakes/burning rubber smell.
View 14 Replies
My 2003 F-250 5.4l gas started making a recurring clicking sound from under the dash on the left side. It started last summer and would repeat numerous times each time I had the truck out. It's the kind of sound the turn signal makes. Always 5 clicks. It stopped happening when the weather got cold here in Canada, but started again this week (maybe because of the the warm weather we're having). How do I troubleshoot what the issue is? If the headlights are off it also flashes the lights in the instrument cluster five times.
View 4 Replies
Took the truck out the other night, got to town felt the slight drag but nothing alarming, got out of the truck and could smell it, rear drivers side rotor glowing red, pass side not glowing, pressed park brake then released, driver side freed on its own, pass side sticking, replaced pass side rotor and pads, found nothing out of the ordinary... Ford F250 4x4, 2005 ....
View 14 Replies
I just replaced the head lights on my 2001 f250 it had the sealed beam one-piece glass headlights and I replaced those with regular headlights and when I went to get bulbs I found out after I get home the connector is different from the new bulbs. the new bulbs fit correctly but I can not hook plug them the plug has 3 connectors that have two connectors level and one is higher than the other two and the new bulbs the three prongs are level.
My question is. is there another bulb that will fit and plugin and if so what is the part number? is there a adapter that I can get that will allow the factory plug to work? or will I need to cut the old plug off and splice a new connector on?
View 8 Replies
